Ikegami HC-HD300 Operation Manual page 100

5.2 Settings from the Menu
■ MENU (2/4)
Menu Item
VIDEO OUTPUT MODE
― SDI OUT
― MON SDI OUT
― MON ANA OUT
― Q-TV ANA OUT
― AUX ANA OUT
VBS CONFIG
ASPECT
MID/HIGH GAIN MODE
― MID GAIN
HIGH GAIN
BATTERY WARNING
BATT WARN VOLT
BARS MODE
― BARS MODE
BARS ON
FAN CONTROL
― FAN CONT MODE
― HEAD TOP
― ADAPTOR
― VF CONT
― FAN CONDITION
― HEAD TOP
ADAPTOR
H PHASE CONTROL
H PHASE
TIME SETTING
― TIME
DATE (YY/MM/DD)
84
Initial
Setting value
setting
ON ON, OFF
VF VF, MAIN, RETURN
MON MON, SYNC
Q-TV1 Q-TV1, Q-TV2, VBS, OFF
VBS VBS, Q-TV1, Q-TV2, OFF Selects the output signal of the AUX output connector.
SQUEEZE, LETTER
SQUEEZE
BOX, SIDE CROP
-3dB -6 to +12dB
+6dB -3 to +18dB
11.0V 10.5 to 13.5V
Destination
FULL, MULTI
setting
OFF ON, OFF
AUTO, SLOW, QUIET,
AUTO
STOP
---
--- (information display)
---
---
(information display)
---
0.0 -100 to +100
--- HH : MM : SS
--- YY / MM / DD
HC-HD300 1412 VER1 (U)
Description, Remarks
Turns the HD-SD signal (mainline) output ON/OFF.
Switches the signals (HD-SDI) output from the MON SDI
OUT connector.
VF : Outputs same signals as VF images.
MAIN : Outputs main line signals.
RETURN : Outputs RET signals.
MON : Outputs micro-analog HD signals for monitor.
SYNC : Outputs tri-level SYNC signals.
Selects output signals from Q-TV output connector.
VBS is the down convert signal of the main line signal.
Sets the output of the down convert signal of the main line
signal.
Sets the gain values allocated to the M and H positions of the
GAIN SELECT switch on the right side of the camera.
Sets the medium gain value allocated to the M position of the
GAIN SELECT switch.
Sets the high gain value allocated to the H position of the
GAIN SELECT switch.
Sets the battery voltage threshold to display warning.
FULL : Displays the BARS signal conventionally used.
MULTI : Displays the multiformat BARS signal.
Turns the color bar signal ON/OFF.
AUTO : Automatically changes the cooling fan speed
according to the internal temperature level.
SLOW : Sets the fan to SSLOW for 5 minutes. After 5
minutes, the mode changes to AUTO.
QUIET : Stops the fan until the external temperature
becomes about 35 ℃ . Above that temperature the
fan is operated automatically.
STOP : Keeps the fan stopped as long as the internal
temperature does not reach a critical level. If the
power is turned on again, it returns to AUTO.
* If the QUIET, STOP modes are chosen, the surface
temperature of the box may become higher than normal.
SSLOW : Fan speed is very slow.
SLOW : Fan speed is slow.
NOR : Fan speed is normal.
FAST : Fan speed is fast.
OK : Normal
NG : Fan is stopped.
Adjusts the horizontal phase when using external sync.
Sets so that the phase of the internal SYNC signal matches
the phase of the external SYNC signal. The internal SYNC
advances in the direction of -100 in relation to the external
synch, and delays in the direction of +100.
*Can only be set during self-operation.
Sets the time and date when saving the file to the memory
card.
MENU DATA
ALL VF
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
× ×
× ×
- -
- -
× ×
- -