Ikegami HC-HD300 Operation Manual page 108

5.2 Settings from the Menu
Menu Item
― INCOM MODE
― INCOM MODE SETUP
― DATA LOAD
― INCOM1 MIX
― INCOM2 MIX
― INCOM1 -> INCOM2
― INCOM1 <- INCOM2
― AFTER VR MIX
― INCOM1 -> INCOM2
― INCOM1 <- INCOM2
DATA SAVE
― PGM FRONT VR
― PGM SETUP
― PGM LEVEL
― PGM2 OUT PGM2
― PGM2 OUT PGM3
― PGM2 OUT MIC1
PGM2 OUT MIC2
BELT PACK(OPTION)
― INCOM1 B.P
INCOM2 B.P
ENGINEER SET FILE RENEW
DATA RENEW MODE
*4 : Selection switch on the rear panel of the MIC line typically controls only the TALK line, but SW LINK to be selected TALK line and LISTEN line both can be
controlled.
92
Initial
Setting Value
Setting
NORMAL, CROSS,
NORMAL 1LINE ENG, USA,
USER1, USER2
READY, NORMAL,
CROSS, 1LINE ENG,
READY
USA, USER1, USER2,
CANCEL
ENG, PRD, BOTH,
ENG
SW LINK, OFF
ENG, PRD, BOTH,
PRD
SW LINK, OFF
OFF ON, OFF
OFF ON, OFF
OFF ON, OFF
OFF ON, OFF
READY, USER1, USER2,
READY
CANCEL
PGM1 PGM1, PGM2
LOW NORMAL, LOW
ON ON, OFF
OFF ON, OFF
OFF ON, OFF
OFF ON, OFF
OFF ON, OFF
OFF ON, OFF
HC-HD300 1412 VER1 (U)
Description, Remarks
Sets the connection (preset setting) of INCOM line.
Sets the connection for when USER1/USER2 is selected in
INCOM MODE PRESET.
Load the setting that becomes a base of the setting.
Selects the line such that whether TALK line of INCOM1
is linked to ENG line, PROD line, both lines, or SW on the
*4
back side, etc.
Selects the line such that whether TALK line of INCOM2
is linked to ENG line, PROD line, both lines, or SW on the
*4
back side, etc.
Connects TALK line of INCOM1 to INCOM2.
Connects TALK line of INCOM2 to INCOM1.
Connects TALK line of INCOM1 to INCOM2.
Connects TALK line of INCOM2 to INCOM1.
Saves data as USER1 or USER2.
Selects the signal to be controlled by PGM volume on the
right side of camera.
Sets the output level of PGM. (Reduced by 10 dB with LOW)
Sets the ON/OFF for outputting PGM2 signal to PGM2.
Sets the ON/OFF for outputting PGM3 signal to PGM2.
Sets the ON/OFF for outputting MIC1 signal to PGM2.
Sets the ON/OFF for outputting MIC2 signal to PGM2.
Turns on when the belt pack is connected to INCOM1.
Turns on when the belt pack is connected to INCOM2.
Saves the conditions of camera level adjustment and menu.
The saved data can be loaded as user settings data of
"PRESET FILE LOAD" in MENU(3/4).
MENU DATA
ALL VF
× ×
- -
○ ×
○ ×
○ ×
○ ×
○ ×
○ ×
- -
× ×
○ ×
○ ×
○ ×
○ ×
○ ×
× ×
× ×
- -