Configuring Motion Cameras For Video Alarm Verification - Visonic PowerMaster-10 Installer's Manual

3.6.6 Configuring Motion Cameras for Video Alarm Verification

If equipped with a GSM/GPRS module, the PowerMaster-10 / PowerMaster-30 can communicate to Monitoring
Stations (equipped with Visonic PowerManage server) via the GPRS network, also image clips captured by
Motion Cameras (models Next CAM PG2 & Next-K9 CAM PG2). The Monitoring Station can use the video clips
for verification of Burglary alarms detected by the Motion Cameras. The system can be configured to capture
image clips also upon occurrence of Non-Burglary alarms (i.e. Fire, Duress, Emergency and Panic). The server
can then forward the images to the management computer of the monitoring station or to 4 remote computers
via e-mail and/or 4 mobile phones by MMS images.
In addition, the monitoring station can log into the PowerManage server and request the system to provide also
image clips "On Demand" and to forward them as defined in the PowerManage application. To protect customers'
privacy, the PowerMaster-10 / PowerMaster-30 can be customized to enable the "On Demand View" only during
specific system modes (i.e. Disarm, Home & Away) and also to a specific time window following an alarm event. In
this section you can program the 4 e-mail addresses and mobile phone numbers to which the images will be
forwarded and to configure the parameters of the "On Demand View" according to your customer's needs.
04.COMMUNICATION
To configure an option enter the
guidance above and in section 3.6.1), then refer to the table below which provides you with detailed
explanations and configuration instructions for each option.
Option
IMAGE FORWARD
1st e-mail
2nd e-mail
3rd e-mail
4th e-mail
1st MMS tel #
2nd MMS tel #
3rd MMS tel #
4th MMS tel #
VIEW ON DEMAND
VIEW TIME WINDOW
"VIEW TIME
WINDOW" menu
appears only if an
option other than
"Disabled" is selected
in "VIEW ON
DEMAND"
64
5:MOTION CAMERAS
5:MOTION CAMERAS
Configuration Instructions
Here you can enter the four e-mail addresses and/or 4 mobile phone numbers to which
you wish the PowerManage server to forward the image clips captured by the Motion
Cameras.
To program:
Press to enter the
of the four e-mail numbers and then each of the four mobile phone numbers. When
done, press to return.
st nd rd
Enter the 1 , 2 , 3 and 4
below) then enter the 1
st
locations (1 MMS tel # etc.)
Note: To enter the e-mail addresses, to move the cursor and clear digits, use the
"String Editor's" keys as described in the table at the end of section 3.6.3.
Here you can enable the "On Demand View" and determine during which arming modes
(system states) the "On Demand View" will be permitted. In the next Option "VIEW TIME
WINDOW" you can determine when during the permitted arming modes the "On
Demand View" will be enabled.
Option settings: Disabled (default); in all modes; in AWAY only; in HOME only; in
HOME & AWAY; DISARM & AWAY; DISARM & HOME; in DISARM only.
If the "On Demand View" is enabled in the previous option, you can further determine
here whether the "On Demand View" will be possible at any time during the selected
arming modes (i.e. "Always") or restricted only to a specific limited time window that
follows an alarm event.
Option settings: Always (default); Alarm + 5 min.; Alarm + 15 min.; Alarm + 1 hour
OPTION you wish
menu, select the option you wish to configure (see
sub menu and then select and program each
IMAGE FORWARD
th
e-mail addresses in their corresponding locations (see note
st nd rd th
, 2 , 3 and 4 mobile phone numbers in their corresponding
D-303222 PowerMaster-10 / PowerMaster-30 Installer's Guide
Means and
scroll select