Configuring Events Reporting To Private Users - Visonic PowerMaster-10 Installer's Manual

Event Reporting Chart
To simplify the configuration of reporting system events to Central Monitoring Stations, the event messages are
divided into 5 Event Groups as described in the following table below: Due to lack of space in the display, the
following abbreviations are used alrm
Event Group
Alarms
Open/close
Alerts
Maintenance
Trouble
Note: "Alarms" group has the highest priority and "Alerts" group has the lowest priority.
The PowerMaster-10 / PowerMaster-30 allows you also to select which event groups will be reported to each of
the two Central Monitoring Stations. The table below describes the available reporting options. The minus (- - - - )
symbol means "but/less/except" e.g. all(
separator between event messages reported to Central Monitoring Station 1 (C.S.1) and event messages
reported to Central Monitoring Station 2 (C.S.2).
Available Reporting Options
"all all backup" backup
all all backup backup
"all
all- - - - o/c all all backup backup" backup backup
o/c o/c o/c
"all all all" all
all all all all
"all o/c "
all all- - - - o/c all all all- - - - o/c all all
o/c o/c o/c o/c o/c
"all o/c "
all– – – – o/c all all
o/c o/c
o/c o/c o/c o/c
"all(
all(– – – – alrt) alrt) alrt" alrt
all( all( alrt) alrt) alrt alrt
"alrm
alrm alrm alrm all(– – – – alrm) all( all( all( alrm) alrm)" alrm)
"disable report disable report"
disable report disable report
Note: "all" means that all 5 Groups are reported including Trouble messages - sensor / system low battery,
sensor inactivity, power failure, jamming, communication failure etc.

3.6.5 Configuring Events Reporting to Private Users

The PowerMaster-10 / PowerMaster-30 system can be programmed to send various event notifications such as
alarm, arming or trouble events, to 4 Private telephone subscribers using audible signals and if a GSM option is
installed, the system can send the messages also to 4 SMS telephone numbers. These reports can be
programmed either instead of or in addition to the reports transmitted to the monitoring company. In this section
you configure:
The specific events you wish the system to report.
•
st nd rd
The 1 , 2 , 3 , and 4
•
The number or redial attempts, two-way voice communication
•
whether a single acknowledge signal will stop the reporting process or an acknowledge signal from each
telephone will be required before the reported event is considered reported.
To select and configure an option follow the instructions below. Additional details and guidance are provided in
section 3.6.1.
04.COMMUNICATION
The configuration and detailed description of the
Chapter 6 section C.11 and therefore will not be repeated here. The detailed menu and sub-menu options are
shown in section 3.6.1 above.
Refers to PowerMaster-30 with voice option only
∗
D-303222 PowerMaster-10 / PowerMaster-30 Installer's Guide
o/c" and all (i.e. all events) – see table below.
alrm, alrt alrt, o/c
alrm alrm alrt alrt
o/c o/c
Abbr. Events Messages Reported
Fire, Burglary, Panic, Tamper
alrm
Arming AWAY, Arming HOME, Disarming
o/c
No-activity, Emergency, Latchkey
alrt
- Low-battery, AC failure
- All other Trouble events not indicated above such as Missing,
Jamming, Communication Fail etc.
all(- - - - alrt all( all( alrt) ) ) ) alrt alrt
Events Reported to C.S. 1
All
All but open/close
All
All but open/close
All but open/close
All but alerts
Alarms
None
th
Private telephone and SMS numbers of the private subscribers.
4:PRIVATE REPORT
means events except
all all all all
Events reported to C.S. 2
All, only if C.S.1 does not respond
All but open/close, only if C.S. 1 does not
respond
All
All but open/close
Open/close
Alerts
All but alarms
None
∗ and your preferred acknowledge method i.e.
OPTION you wish
options is provided in the User's Guide
4:PRIVATE REPORT
The asterisk ( ) is a
.
alerts s s s alert alert alert
Means
scroll
and
select
63