Reporting To Private Telephone - Visonic PowerMaxComplete User Manual

SPECIAL FUNCTIONS
B. Executable Commands
Command Keying Sequence
Disarming
[ ] [1] [#]
Arming Home
[ ] [2] [#]
Arming Home-Instant
[ ] [2]
Arming Away
[ ] [3] [#]
Arming Away-Instant
[ ] [3] [1] [#]
Arming Away-Latchkey
[ ] [4] [#]
Arming Away-Instant- [ ] [4]
Latchkey
Activating PGM output [ ] [5] [0]
Deactivating PGM output [ ] [5] [0]
Two-way voice [ ] [7]
communication
(see sub-par. C)
Recorded message [ ] [8]
playback
Recorded message start [ ] [8]
record
Recorded message stop [ ] [8]
record
Recorded message [ ] [8]
erase message
Investigating system [ ] [9] [#]
status
Quit (end [ ] [9] [9] [#]
communication)
C. Two-Way Voice Communication
Perform steps 1-6 in Establishing Telephone
Communication above and continue as follows:
[
1. [ ] [7] #]
2. Wait for 2 beeps
3. [3] or [1] or [6] (see below)
The system will start to function in the "LISTEN IN"
mode, letting you hear the sounds within your residence
for 50 seconds. If the person under surveillance
happens to speak or cry then, you will hear this. You
can switch the system to Listen-In, Speak Out or Full
Duplex, as shown in the next table.
Command
Listen-in (listening to the person at home) (*)
Speak-out (speaking to the person at home) (*)
Full-duplex (listening & speaking) (*)
Note: To prolong the communication session
by 50 seconds, press [3], [1] or [6] again, as
required.
* The 2-way communication can be terminated by
anyone close to the PowerMaxComplete, by
disarming the system.
18
Remark Regarding Listen-in & Speak-out modes
Listen-in & Speak-out modes allow one way speech at
a time. Back and forth exchange of uninterrupted
speech between two parties is a method normally
used in military, commercial and amateur radio
communication. Once you finish talking you should
[ 1] [#]
say "Go Ahead" or "Over" and then switch from speak-
out to listen in. When the person at home finishes
talking he should also say "Over", as a cue to you to
switch back from Listen-in to speak out.
EXAMPLE:
[ 1] [#]
You (at remote telephone):
can you hear me? Are you in any trouble? Over"....
[0] [1] [#]
[3]
[0] [0] [#] Person at home: "Yes, I am. I had a dizzy spell while
trying to get out of bed and fell on the floor. I am
[ #]
unable to get up and my thigh hurts. Can you help
me? Over"...
You (at remote telephone):
[ 1 ] [#]
send someone right away, stay put - over"..
Person at home: "Thanks, please hurry, over".
[ ]
2 [#]
You (at remote telephone):
[ 3 ] [#]
and out".....
Important!
communication
[ 4 ] [#]
command, just press [ ] and then key your user
code followed by the command (see "keying
sequences" in Executable Commands table above).

Reporting to Private Telephone

control
panel
The PowerMaxComplete can be programmed by the
installer for selective transmission of messages to
private telephone subscribers. Messages are divided
by type into 3 groups:
Group Events Reported
1
2
3
Note: In control panel with no-voice option, the
following siren signal will be sent to private telephone
Key
upon event reporting:
* FIRE: ON - ON - ON - pause.... (- - - - - - ......).
[3]
** BURGLAR: ON continuously (
[1]
*** EMERGENCY: 2-tone siren; like an ambulance.
[6]
Group 1 has the highest priority and group 3 has the
lowest priority.
When the called party answers a call initiated by the
PowerMaxComplete, he will hear a verbal message
composed of the "house identity" and the type of
event that occurred. For example, once smoke is
detected in the Smith residence, the message will
be: [The Smith Residence - Fire Alarm].
[1], "Hey, George,
[1], "Sure, I will
[1], "All right, over
[ ] 9] [9] (END OF SESSION)
If you wish to exit
mode and execute
Fire (*), Burglary (**), Panic, Tamper
Arming AWAY, Arming HOME, Disarming
No-activity, Emergency (***), Latchkey
[3].
the two-way
another
...)
D-300886