Ricoh CL1000N User Manual page 2

QUICK INSTALLATION GUIDE
Please read the Safety Information in the "Maintenance Guide" before using this printer.
It contains important information related to USER SAFETY and PREVENTING EQUIPMENT
PROBLEMS.
Pull out the two orange stop tags that have red
UNPACKING THE PRINTER AND
cards attached to them.
CHECKING THE CONTENTS OF
THE BOX
Caution
• The printer weights approximately 31.5 kg (69.4
lb). When moving the printer, use the inset grips
on both sides, and lift slowly. The printer will
break or cause injury if dropped.
Check the contents of the box according to the
following list. If one or some items are missing,
please contact your sales or service ❒ If the printer is used with any of the stop tags still
representative. attached, poor fusing will occur. Be sure to remove
all of the stop tags.
Important
Close the rear cover.
❒ The parallel cable is not included in the box. It is
your responsibility to provide the parallel cable
appropriate for the computer you are using.
Quick Installation Guide (this sheet)
Option Setup Guide
Maintenance Guide
CD-ROM
Photo Conductor Unit
WHERE TO PUT THE PRINTER
Power Cord
The printer's location should be carefully chosen
Ferrite Core
because environmental conditions greatly affect its
Controller Board Screwdriver
performance.
Color Calibration Sample Sheet
Warning
Remove the plastic bag.
• Confirm that the wall outlet is near the printer
and freely accessible, so that in event of an
emergency, it can be unplugged easily.
Lift the printer and move it to the place where
• Only connect the printer to the power source
you want to install it.
described on this sheet.
• Avoid multi-wiring.
When lifting the printer, use the inset grips on both sides of the
• Do not damage, break or make any
printer.
modifications to the power cord. Do not place
heavy objects on it, pull it hard or bend it more
than necessary. These actions could cause an
electric shock or fire.
Caution
• Keep the printer away from humidity and dust.
A fire or an electric shock might occur.
• Place the printer on a strong and level surface.
Otherwise, the printer might fall and cause
personal injury.
AAL007S
• If you use the printer in a confined space, confirm
Important
that there is a continuous flow of air.
❒ The printer should always be lifted by at least two
people.
Remove all tape securing the printer's moving
parts.
Pull the rear cover open lever, and then open the
rear cover.
AAL009S
<G108-8608>
Optimum Environmental Conditions
Recommended temperature and humidity
RH
10 80
80
15
60
40
15
20
10 15
AAL010S
10
Important
RH
50 80
80
59
60
40
59
20
50 15
50 60
Possible operation range
The printer must be level within 5 mm, 0.2" both front to rear and
left to right.
To avoid possible build-up of ozone, place this printer in a large well
ventilated room that has an air turnover of more than 30 m
person.
If you use this printer in a cold area, leave the printer on or severe
cold might damage sensitive components inside the printer.
Environments to Avoid
Important
❒ Locations exposed to direct sunlight or strong light
❒ Dusty areas
❒ Areas with corrosive gases
❒ Areas excessively cold, hot, or humid
❒ Locations near an air conditioner or humidifier
❒ Locations near other electronic equipment
❒ Locations where the printer might be subjected to
frequent strong vibration
Power Connection
Connect the power cord to a power source with the following
specifications:
❒ 120 V, 60 Hz, 11 A or more
Space Required for Installing the Printer
Leave enough space around the printer. This space is necessary to
operate the printer. The recommended (or minimum) space
requirement is as follows:
C
A: more than 25 cm (9.9") (More than 35 cm (11.9") when the
AD460 (duplex unit) is attached.)
B: more than 20 cm (7.9")
C: more than 70 cm (27.6")
D: more than 50 cm (19.7")
INSTALLING THE TONER CARTRIDGES
Warning
27 80
• Do not incinerate spilled toner or used toner. Toner
dust might ignite when exposed to an open flame.
70 27 70
• Disposal can take place at our authorized dealer
32.5 60
or at an appropriate collection site.
• If you dispose of the used toner containers
yourself, dispose of them according to your local
30 27 30
regulations.
Caution
32.5 15
• Do not open the front cover when the paper tray
is pulled out halfway. If you do, it might cause a
20 30
personal injury.
AAL990S
• Do not eat or swallow toner.
80.6 80
• Keep toner (used or unused) and toner
cartridges out of reach of children.
70 80.6 70
• Our products are engineered to meet the highest
90.5 60
standards of quality and functionality. When
purchasing expendable supplies, we
recommend using only those provided by an
30 80.6 30
authorized dealer.
Important
90.5 15
❒ The locations for the attachment of the toner
70 80 90
cartridges are in order from the top: black (K),
AAL991S
yellow (Y), magenta (M), and cyan (C).
Recommended range
The supplied toner cartridge is inside the machine.
Here, the black (K) toner cartridge is used as an
example to explain the procedure of preparing a
3 toner cartridge. Prepare other toner cartridges
/hr/
following the same procedure.
Pull the front cover open lever, to open the front
cover.
Remove the packing material fastening the four
toner cartridges.
B
Remove the top toner cartridge (black).
A
D
AAL276S
Hold the new toner cartridge and shake it well, about
3 to 4 times, as shown in the illustration.
AAL019S
Important
❒ Printing quality may decrease if the toner is unevenly
distributed inside the toner cartridge.
Remove the protective cover.
Remove the tape securing the protective cover
while holding the toner cartridge as shown.
Important
❒ The tape is attached from the front to the back of
the toner cartridge. Make sure to remove all of the
tape.
❒ Do not touch the development roller which is
exposed after removing the protection cover, as this
may lead to a deterioration in the printing quality.
❒ Once the protective cover is removed, toner can spill
from the cartridge easily. Take care to avoid
subjecting the toner cartridge to vibration and
impact after removing the protective cover.
AAL055S
Insert the new toner cartridge (black) in the same
location.
AAL018S
With the seal side surface facing up, align it with position K on the
printer, and then slide in the toner cartridge along the guide rails.
AAL035S
AAL022S
Important
❒ Do not use excessive force to slide the cartridge.
❒ Do not repeatedly install and remove the toner
cartridges. Doing so will cause toner leakage.
Repeat the procedures to to prepare the
other toner cartridges.
AAL036S
Remove the cyan toner cartridge at the bottom
(A).Pull out the orange tape to remove the
protective paper (B), and then install the cyan
toner cartridge again.
AAL299S
Close the front cover until the center of the front
cover locks securely.
INSTALLING THE PHOTO
CONDUCTOR UNIT
Important
❒ Exposing the photo conductor unit to light for too
long can reduce its performance. Replace the unit
as quickly as possible.
Open the top cover using the finger grip.
AAL012S
Remove the pins on both sides of the photo
conductor unit.
AAL013S