Related Manuals - Omron CP - PROGRAMMING MANUAL 05-2007 Programming Manual

Related Manuals

The following manuals are used for the CP-series CPU Units. Refer to these manuals as required.
Cat. No. Model numbers
W451 CP1H-X40D@-@
CP1H-XA40D@-@
CP1H-Y20DT-D
CP1L-L14D@-@
CP1L-L20D@-@
CP1L-M30D@-@
CP1L-M40D@-@
W450 CP1H-X40D@-@
CP1H-XA40D@-@
CP1H-Y20DT-D
W462 CP1L-L14D@-@
CP1L-L20D@-@
CP1L-M30D@-@
CP1L-M40D@-@
W461 CP1L-L14D@-@
CP1L-L20D@-@
CP1L-M30D@-@
CP1L-M40D@-@
W342 CS1G/H-CPU@@H
CS1G/H-CPU@@-V1
CS1D-CPU@@H
CS1D-CPU@@S
CS1W-SCU21
CS1W-SCB21-V1/41-V1
CJ1G/H-CPU@@H
CJ1G-CPU@@P
CP1H-CPU@@
CJ1G-CPU@@
CJ1W-SCU21-V1/41-V1
W446 WS02-CXPC1-E-V70
W447 WS02-CXPC1-E-V70
W444 CXONE-AL@@C-E
Manual name
SYSMAC CP Series Provides the following information on the CP Series:
CP1H and CP1L CPU
• Programming instructions
Unit Programming
• Programming methods
Manual
• Tasks
(This manual)
• File memory
• Functions
Use this manual together with the CP Series CP1H
CPU Units Operation Manual (W450) and CP
Series CP1L CPU Units Operation Manual (W462)
SYSMAC CP Series Provide the following information on the CP Series:
CP1H CPU Unit
• Overview, design, installation, maintenance, and
Operation Manual
other basic specifications
SYSMAC CP Series
• Features
CP1L CPU Unit Oper-
• System configuration
ation Manual
• Mounting and wiring
• I/O memory allocation
• Troubleshooting
Use this manual together with the CP1H Program-
mable Controllers Programming Manual (W451).
SYSMAC CP Series Provides basic setup information for CP1L PLCs,
CP1L Introduction including the following.
Manual
• Basic configuration and part names
• Mounting and wiring procedures
• Programming, program transfer, and debugging
with the CX-Programmer
• Application programming examples using the
CP1L
SYSMAC CS/CJ- Describes commands addressed to CS-series, and
series Communica- CJ-series CPU Units, including C-mode commands
tions Commands Ref- and FINS commands.
erence Manual
Note This manual describes on commands
SYSMAC CX-Pro- Provides information on installing and operating the
grammer CX-Programmer for all functions except for function
Ver. 7.0 Operation blocks.
Manual
SYSMAC CX-Pro- Provides specifications and operating procedures
grammer Ver. 7.0 for function blocks. Function blocks can be used
Operation Manual with CX-Programmer Ver. 6.1 or higher and either a
Function Blocks CS1-H/CJ1-H CPU Unit with a unit version of 3.0 or
a CP1H CPU Unit. Refer to W446 for operating pro-
cedures for functions other than function blocks.
CX-One FA Inte- Provides an overview of the CX-One FA Integrated
grated Tool Package Tool and installation procedures.
Setup Manual
Description
address to CPU Units regardless of the com-
munications path. (CPU Unit serial ports,
Serial Communications Unit/Board ports, and
Communications Unit ports can be used.)
Refer to the relevant operation manuals for
information on commands addresses to Spe-
cial I/O Units and CPU Bus Units.
xvii