AB Quality Allen-Bradley 1394 User Manual page 236

B-4 Interconnect and CE Diagrams
NOTES 8, 9
BLUE
SHIELD
CLEAR
FROM 1746 I/O RACK OR A 1746 RACK
WITH AN SLC 5/03, 5/04, OR 5/05 PROCESSOR
TO SLC RACK OR 1394-SJT xx -T
SYS ENABLE
24V INPUT COM
NOTES 15, 16, 19
SHIELD
HOME 0
POS 0TRAV 0
NOTES 3, 5
NEG 0TRAV 0
THERM FLT 0
24V INPUT COM
SHIELD
HOME 2
POS 0TRAV 2
NEG 0TRAV 2
THERM FLT 2
24V INPUT COM
SHIELD
REG0 5V
REG0 24V
REG COM
SHIELD
REG2 5V
REG2 24V
REG COM
SHIELD
A TEST 0
NOTE 7
A TEST 1
A TEST COM
SHIELD
DATA A
DATA B
NC
NC
TX ENAB
SHIELD
COM
NC
22 KW INPUT POWER
NOTE 25
Publication 1394-5.0 — May 2000
Figure B.2
GMC System Interconnection Diagram
(1394 x -SJT xx -C and -T)
1394 GMC AND GMC TURBO
RIO BOARD
SYSTEM MODULE
A
1
P1 NOTE 17
2
DC MINUS BUS
NOTE 13
SLC IN
Refer to the Wiring System, Axis, and Shunt Modules,
and Motors (for all systems) chapter
for ground jumper instructions.
SLC OUT
Motion Input Wiring Board
TB1
1
2
1394 x -SJT xx -C, -C-RL
3
and
4
5
1394 x -SJT xx -T, -T-RL
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DRIVE O.K. RELAY
25
RATED AT 115VAC, 24VDC,
26
1A INDUCTIVE
27
DH-485 DH-485
J1 J2
1 1
2 2
3 3
4 4
5 5
6 6
7
7
8 8 5 AND 10 KW INPUT POWER
SYSTEM MODULE
GROUND BAR
(Series C)
A
FACILITY GROUND
* INDICATES USER SUPPLIED COMPONENT
TB2
SYS ENABLE
1
24V INPUT COM
2
SHIELD
3
HOME 1
4
POS 0TRAV 1
5
NEG 0TRAV 1
6
THERM FLT 1
7
24V INPUT COM
8
SHIELD
9
HOME3
10
POS 0TRAV 3
11
NEG 0TRAV 3
12
THERM FLT 3
13
24V INPUT COM
14
SHIELD
15
REG1 5V
16
REG1 24V
17
REG COM
18
SHIELD
19
REG3 5V
20
REG3 24V
21
REG COM
22
SHIELD
23
DRIVE OK1
24
DRIVE OK2
25
CHASSIS
26
CHASSIS
27
DS1
SOLID GREEN = BUS UP, AXIS ENABLED
FLASHING GREEN = BUS UP, AXIS NOT ENABLED
FLASHING RED/GREEN = READY, BUS NOT UP
FLASHING RED = FAULT
SOLID RED = HARDWARE FAILURE
(Series C)
NOTE 17
CONTROL POWER
& SIGNALS
DC BUS POS.
DC BUS NEG.
SLIDER INTERCONNECT
NOTES 15, 16, 19
NOTES 3, 5
NOTES 3, 6
START*
STOP*
CR1*
CR1*
M1*
CR1*
5 AND 10 KW INPUT POWER
(Series A and B)
24V AC/DC
or
120V AC,
50/60 HZ