Advertisement
Wing Tooth Control
Installation
NOTE
2 Hole Strap Stops hold the position of Tooth Tubes.
Left Wing
1. Attach a Tooth Control Bracket on the top of the Front
Tooth Tube by sliding a Clamp Plate into the Tooth
Control Bracket Slot and under the Tooth Tube.
Fasten with 5/8-11 x 5 Bolts and Locknuts, Do Not
tighten at this time. See Figure 2-61.
2. Lay the Cylinder Rod Clevis between the Tooth
Control Bracket Lugs. Position the Tooth Control
Tube over the top of the Cylinder Rod Clevis and
between the Tooth Control Bracket Lugs and insert a
1 x 6-1/2 Pin. Place a 1" Flat Washer on each side of
the Pin against the Tooth Control Bracket. Secure
with 5/16 x 2 Roll Pins.
3. Position a Tooth Control Clamp w/cutout on top of the
Rear Tooth Tube while straddling the Tooth Control
Tube. Insert 1 x 6-1/2 Pins. Place a 1" Flat Washer on
each side of the Pin against the Tooth Control Clamp
and secure with 5/16 x 2 Roll Pins. Tooth Control
Clamps should be aligned with each other.
4. Attach Tooth Control Clamp on the Tooth Tube with
two 5/8-11 x 5 Bolts and two 5/8-11 x 2 Bolts and
Locknuts and 4 Hole Plate.
5. Position a Tooth Control Bracket on top of the Left
Middle Tooth Tube while straddling the Tooth Control
Tube. Insert 1 x 6-1/2 Pins. Place a 1" Flat Washer on
each side of the Pin against the Tooth Control Bracket
and secure with 5/16 x 2 Roll Pins.
6. Attach Tooth Control Bracket on Tooth Tube by
sliding a Clamp Plate into the Tooth Control Bracket
Slot and under the Tooth Tube. Fasten with 5/8-11 x
5 Bolts and Locknuts.
Tighten hardware after positions of clamps and tube have
been verified. See Figure 2-59.
Right Side
1. Attach a Tooth Control Bracket on the top of the right
Front Tooth Tube by sliding a Clamp Plate into the
Tooth Control Bracket Slot and under the Tooth Tube.
Fasten with 5/8-11 x 5 Bolts and Locknuts, Do Not
tighten at this time. See Figure 2-62.
2. Lay the Cylinder Rod Clevis between the Tooth
Control Bracket Lugs. Position the Tooth Control
Tube over the top of the Cylinder Rod Clevis and
between the Tooth Control Bracket Lugs and insert a
1 x 6-1/2 Pin. Place a 1" Flat Washer on each side of
the Pin against the Tooth Control Bracket. Fasten with
5/16 x 2 Roll Pins.
F-982-0223
TABLE OF CONTENTS
3. Position a Tooth Control Clamp w/cutout on top of the
right Rear Tooth Tube while straddling the Tooth
Control Tube. Insert 1 x 6-1/2 Pins. Place a 1" Flat
Washer on each side of the Pin against the Tooth
Control Clamp and fasten with 5/16 x 2 Roll Pins.
Tooth Control Clamps should be aligned with each
other.
4. Attach Tooth Control Clamp on the Tooth Tube with
two 5/8-11 x 5 Bolts and two 5/8-11 x 2 Bolts and
Locknuts and 4 Hole Plate. Ensure that both linkages
don't bind and the Tooth Control Clamps and the
Tooth Tubes are positioned correctly. Tighten the
Bolts and Nuts at this time.
5. Position a Tooth Control Bracket on top of the right
Middle Tooth Tube while straddling the Tooth Control
Tube. Insert 1 x 6-1/2 Pins. Place a 1" Flat Washer on
each side of the Pin against the Tooth Control Bracket
and secure with 5/16 x 2 Roll Pins.
6. Attach Tooth Control Bracket on Tooth Tube by
sliding a Clamp Plate into the Tooth Control Bracket
Slot and under the Tooth Tube. Fasten with 5/8-11 x
5 Bolts and Locknuts.
Tighten hardware after positions of clamps and tube
have been verified. See Figure 2-60.
ASSEMBLY
2-65
Advertisement
