Summary of Contents for Landoll 2511 IN-3-30 2511 N-4-30 2511 N-5-30
Page 1
2512 In-Row Ripper FOR UNITS SHIPPED AFTER DECEMBER 1, 2020 (SN: 25M201237 AND ABOVE) PREVIOUS UNITS SHOULD REFERENCE F-1040-0320 Operators Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-1040-0123...
Page 2
Manuals for 2512 In-Row Ripper MANUAL NUMBER MANUAL NAME F-1039 2512 In-Row Ripper Parts Manual F-1040 2512 In-Row Ripper Operators Manual F-1075 Caddy Parts Manual (ONLY) F-1040-0123...
Page 3
Table of Contents Introduction and Safety Information Understanding Safety Statements ..........1-2 Decal Safety .
Page 4
TABLE OF CONTENTS Troubleshooting Guide Quick Start Guides 2512 Hydraulic Auto Re-Set Shank Clamp ........6-1 F-1040-0123...
Introduction and Safety Information The Landoll Model 2512 Rigid & Folding In-Row Ripper are quality products designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation.
TABLE OF CONTENTS INTRODUCTION AND SAFETY INFORMATION Understanding Safety Decal Safety Statements 1. Examine safety decals and be sure you have the correct safety decals for the implement. You will find various types of safety information on the 2. Keep these signs clean so they can be observed following pages and on the machine signs (decals) readily.
TABLE OF CONTENTS INTRODUCTION AND SAFETY INFORMATION 2. Block implement so it will not roll when unhitched DANGER from the tractor. 3. Store in an area where children normally do not play. • Do not allow anyone to ride on the tractor or implement.
TABLE OF CONTENTS INTRODUCTION AND SAFETY INFORMATION Tire Safety Safety Chain 1. Tire changing can be dangerous and should be 1. Use a chain with a strength rating equal to or greater performed by trained personnel using correct tools than the gross weight of towed machinery, which is and equipment.
TABLE OF CONTENTS STANDARD SPECIFICATIONS General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS - This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
TABLE OF CONTENTS STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing.
Page 13
TABLE OF CONTENTS STANDARD SPECIFICATIONS Shank Mounting Dimensions - Rigid Figure 2-3: 4-Shank Spacing...
Page 14
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-4: 5-Shank Spacing F-1040-0123...
Page 15
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-5: 6-Shank Spacing...
Page 16
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-6: 7-Shank Spacing F-1040-0123...
Page 17
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-7: 8-Shank Spacing...
Page 19
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-9: Folding - 8 Shank Spacing 2-11...
Page 20
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-10: Folding - 9 Shank Spacing 2-12 F-1040-0123...
Page 21
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-11: Folding - 10 Shank Spacing 2-13...
Page 22
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-12: Folding - 11 Shank Spacing 2-14 F-1040-0123...
Page 23
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-13: Folding - 12 Shank Spacing 2-15...
Page 24
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-14: Folding - 13 Shank Spacing 2-16 F-1040-0123...
Page 25
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-15: Folding - 14 Shank Spacing 2-17...
Page 26
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-16: Folding - 15 Shank Spacing 2-18 F-1040-0123...
Page 27
TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-17: Folding - 16 Shank Spacing 2-19...
Page 28
TABLE OF CONTENTS STANDARD SPECIFICATIONS NOTES: 2-20 F-1040-0123...
Page 29
Be sure to return bolts, clips, do not attempt to release the shank. Contact your etc. to their original locations. Landoll dealer for further instructions. A tripped To ensure assemblies are aligned, insert all bolts and shank can release suddenly and cause serious leave the nuts loose until completion of final injury or death.
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Assembly Preparation 3. For transport, remove the jack stand Hitch Pin, and store the Jack Stand Weldment "off the machine." 1. Hook up the In-Row Ripper to a tractor using the 3-PT Hitch. Rear Jack Stands (Rigid and Folding) 2.
Page 31
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS SMV Bracket Installation 1. Attach the SMV mounting bracket at a point where emblem is visible from rear of machine, using U-Bolt and 5/8-11 Flange Head Serrated Nuts (See Figure 3-3.) 2. Attach SMV emblem to top of SMV mounting bracket using 1/4-20 x 1 Hex Head Cap Screws, Flat Washers, and Locknuts (See Figure...
Page 32
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Right Hand & Left Hand Coulter Tube, 4 U-Bolts, Clamp Plate and 5/8-11 Locknuts. Do not tighten nuts until the depth adjustment is Assemblies completed. 1. Assemble Coulter Adjustment Tube to Coulter 3. Use Adjustment Pin and 3/16 Hairpin to set desired Assembly using Roll Pins 1/2 x 4 and 5/16 x 4.
The RSB Clamp has three holes: the top hole has a maximum operating depth up to 14", the lower two holes have operating depths ranging from 16" to 20". Landoll recommends using the top upper holes for optimal machine efficiency. ...
Page 34
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS DANGER OPERATING AT A DEPTH THAT EXCEEDS THE MAXIMUM SHANK TRIP HEIGHT EXPOSES THIS MACHINE TO DAMAGE THAT MAY LEAD TO PERSONAL INJURY OR DEATH. CLAMP WELDMENT SETBACK OPTION TORQUE THE GATE CLAMP BOLTS TO 300-400 FT/LBS The Auto Reset Spring Clamp...
Page 35
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS CLAMP WELDMENT SETBACK OPTION TORQUE THE GATE CLAMP BOLTS TO 300-400 FT/LBS CONNEX WEARSTRIP BUSHING BRACKET WEARSTRIP COVERBOARD KIT SHANK LEG (OPTIONAL) SHOWN: 1-1/4 PARABOLIC SPRING SLOTTED PINS MULTIPLE POINTS AVAILABLE SEE PARTS MANUAL FOR DETAILS Figure 3-6: Auto-Reset Shank Clamp (Hydraulic)
Page 36
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS CLAMP WELDMENT TORQUE THE GATE CLAMP BOLTS TO 300-400 FT/LBS WEARSTRIP BRACKET CONNEX BUSHING WEARSTRIP SHANK LEG SHOWN: 1-1/4 STRAIGHT MULTIPLE POINTS AVAILABLE SEE PARTS MANUAL FOR DETAILS SPRING SLOTTED PINS Figure 3-7: RSB Shank Clamp F-1040-0123...
Page 37
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Coverboard Installation 1. Insert four 1/2-13 x 2-1/2 Bolts into the Coverboard Bracket before attaching the Coverboard Furrower. (See Figure 3-6.) Secure with 1/2-13 Locknuts and tighten only so that locking portion of nut engages the thread.
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Gauge Wheel 1. The Gauge Wheel Assembly comes fully assembled from the factory. (Horizontal Mount and Vertical Mount Options) 2. Attach the Tire and Wheel Assembly to the Hub and tighten the lug nuts to the proper torque as specified inFigure 2-1.
Page 39
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS GAUGE WHEEL ASSEMBLY - VERTICAL MOUNT Used On All Units With Even Number Of Shanks 4 Through 8. DEPTH GAUGE LOCKNUT, 3/4-10 LOCKNUT, 3/4-10 LH, GAUGE GROOVED PLATE-CONTROL TOP LOCK LOCKNUT, 1-8 ROLL PIN TIRE/WHEEL ASSEMBLY SHOULDER SHOULDER WASHER,...
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Electrical Installation 1. Attach left and right (Amber) Light Mount Brackets to frame. (See Figures 3-11 thru 3-12.) 4 Shank: using 3-4-10 x 2 bolts and 3/4-10 lock nuts. Rigid 5,6,7,8 Shank: using 3/8-16 x 1-1/4 bolts and 3/8-16 lock nuts.
Page 41
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS AG FLASHER CONTROL FLAT MODULE WASHER, 1/4W REAR WARNING LIGHTS HARNESS 7-PIN/4-PIN LOCKNUT, HARNESS 1/4-20 BOLT, 1/4-20 X 2 LIGHT MOUNT REFLECTOR BRACKET FLAT WASHER 1/4W LOCKNUT, BOLT, 1/4-20 1/4-20 X 3/4 BRACKET LOCKNUT, 1/4-20 HOLDER LOCKNUT, 1/2-13 BOLT, 1/4-20...
Page 42
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS 7-PIN 4-PIN CIRCUIT WIRE COLOR CONN. TOWER GROUND GROUND – WORK LAMPS BLACK LEFT FLASHING YELLOW & TURN – STOP LAMPS RIGHT FLASHING GREEN & TURN TAIL LAMPS BROWN SWITCHED – BLUE POWER (12 V) LED WARNING LIGHT HARNESS - WIRING CHART 2-PIN 3-PIN...
Page 43
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS General Hydraulic Components - Hydraulic Reset Option Figure 3-13 is provided as a general guideline for the components provided with the Hydraulic Reset Option. It is meant to assist with identifying components on the machine. Each machine size will use a specific quantity of each component during assembly.
Page 44
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Closer Platform (Option) and SPACER/BUSHING Features (After 02/2022) LOCKNUTS RETAINING WASHER The Closer Platform allows the user to mount 5 different SLIDE BUSHING features: Closer Wheel, Flat Bar Basket 20", Closer Disc, SPACER/BUSHING Crumbler Wheel, Packer Reel or Treader. REAR SPRING KEEPER IMPORTANT ALWAYS REPLACE PARTS WITH UPDATED...
Page 45
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Closer Platform (Option) and SPRING ROD GLIDE WASHER Features (Before 02/2022) SPACER SPACER The Closer Platform allows the user to mount 5 different LOCKNUTS REAR SPRING KEEPER features: Closer Wheel, Flat Bar Basket 20", Closer Disc, Crumbler Wheel, Packer Reel or Treader.
Page 46
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-18 F-1040-0123...
Page 47
DANGER Do not attempt to manually reset a shank assembly or straighten a bent shank mount. Contact a Landoll dealer or Landoll Company, LLC, immediately for assistance. DANGER Never allow anyone to ride on the In-Row Ripper at any time.
TABLE OF CONTENTS OPERATION AND MAINTENANCE Tractor Preparation Attaching to 3-PT Hitch The 2512 Series Rigid and The Folding In-Row Rippers 1. Carefully back the tractor into place. up to and thru the 2512F-9 can be used on tractors with 2.
Page 49
TABLE OF CONTENTS OPERATION AND MAINTENANCE 2512 RIGID FRAME 2511N CAT II HITCH CAT III NARROW HITCH USED WITH 3, 4, & 5 NARROW FRAMES 4, 5, 6, 7 & 8 RIGID FRAMES 2512 RIGID FRAME 2511N CAT III NARROW HITCH CAT III HITCH USED WITH 3, 4, &...
Page 50
Escaping hydraulic fluid can cause serious If the system continuously loses pressure, contact personal injury. Relieve system pressure before Landoll Company, LLC and request to speak with a repairing, adjusting, or disconnecting. Wear technician. proper hand and eye protection when searching for leaks.
Page 51
TABLE OF CONTENTS OPERATION AND MAINTENANCE step. The Pressure Reduction Valve Manifold is designed to not allow reverse flow. If the pressure gauge immediately reaches 3000 psi, the hydraulic connections need to be reversed. 5. With the circuit running, open the handled Ball Valve (align the handle with the hydraulic lines entering and leaving the valve).
TABLE OF CONTENTS OPERATION AND MAINTENANCE Hydraulic Fold System WARNING 1. The In-Row Ripper is equipped with a hydraulic fold The wing fold hydraulic system MUST be system to raise and lower the wing frames for narrow operated in float once the wings are unfolded OR transport.
TABLE OF CONTENTS OPERATION AND MAINTENANCE Field Operation - 3-PT Hitch Type 9. Install a new cotter pin and the hub cap. 10. Wheel bearing maintenance should be performed at 1. Lower the In-Row Ripper to the ground and pull it a the beginning of every season of use.
Page 54
TABLE OF CONTENTS OPERATION AND MAINTENANCE Table provided for general use. NOTES: F-1040-0123...
Page 55
Chapter 5 TABLE OF CONTENTS Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 2512 Series Rigid & Folding In-Row Ripper. Follow all safety precautions stated in the previous sections when making any adjustments to your machine.
TABLE OF CONTENTS TROUBLESHOOTING GUIDE NOTES: F-1040-0123...
Page 57
Chapter 6 TABLE OF CONTENTS Quick Start Guides 2512 Hydraulic Auto Re-Set Shank Clamp Quick Start Instruction 1. DO NOT hook the hydraulics up to the tractor at this 5. Adjust the gauge wheels: point!!! a. If the top of the gauge wheel is even with the top 2.
Page 58
TABLE OF CONTENTS QUICK START GUIDES Table provided for general use. NOTES: F-1040-0123...
Page 59
Document Control Revision Log: Date Form # Improvement(s): Description and Comments 01/2020 F-1040 Initial Release 12/2020 F-1040-1220 Added: Folding Shank Mounting Dimensions ECN 46468 - Added Depth Gauge and Decal, Added Hose Mount Plate Extension ECN 46650 - Updated Warning Light Bracket, Gusset-Frame Braces Added: Closer Platform and Features 01/2021 F-1040-0120...
Page 60
Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. 2512 In-Row Ripper and Caddy FOR UNITS SHIPPED AFTER DECEMBER 1, 2020 (SN:25M201237 AND ABOVE) PREVIOUS UNITS SHOULD REFERENCE F-1040-0320...