Related Manuals for Landoll Brillion PPD Series
Summary of Contents for Landoll Brillion PPD Series
- Page 1 ® Pick-up Pulverizer Operator’s and Parts Manual PPD Series 10’ through 20’ PPO Series 10’ through 20’ LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM 1098rev0813 5K804...
- Page 2 5K804...
-
Page 3: Table Of Contents
PICK-UP PULVERIZERS CONTENTS Introduction ............................. 3 Location Reference ........................ 3 Parts Ordering ........................3 Safety Suggestions ........................4 Safety Signs ..........................4 Safety Sign Location ......................5 Operating Instructions ........................6 Warning Light Assembly ......................... 7 Tire Track Remover Assembly ....................... 8 - Machine Specifications .............. - Page 4 5K804...
-
Page 5: Introduction
INTRODUCTION Your Brillion Pulverizer is built with the best materials and workmanship available. It has been designed to give years of trouble-free operation. Proper care and operation will insure that you receive the service and long life built into this machine. Study this manual carefully before attempting to operate the machine. -
Page 6: Safety Suggestions
SAFETY SUGGESTIONS Investigation has shown that nearly one-third of all farm accidents are caused by careless use of machinery. You can do your part in improving safety by observing the following suggestions. Insist that all people working with you or for you abide by them. 1. - Page 7 Decal Locations 1. 8J309 - “Caution” Decal 2. 528938 - Orange Stripe 3. 528933 - Red Reflector 4. 528934 - Yellow Reflector (on frontside of decal plate) 5. 4K103 - Brillion Decal 6. 2P151 - SMV with bracket Figure 2B 1098rev0813 Page 5 5K804...
- Page 8 OPERATION Securely block machine when working on or under it to prevent injury in case of hydraulic failure or inadvertent lowering by another person. This pulverizer is designed to be mounted to tractors with a category II 3-point hitch. Clevis pins (with 1 1/8”...
- Page 9 Red LED Lamp Amber LED Lamp Amber LED Lamp LED Warning Lights Harness Flasher Control Module 7Pin/4Pin WP Harness When plugging in the LED 7-pin connector: 1) Make sure the tractor has a good clean receptacle, free of dirt and corrosion. 2) Make sure the 7-pin connector is inserted ALL the way in.
- Page 10 LED Lamp Placement Dimensions 96” 64” 48” 32” 5 7/8” Red Lamp Red Lamp Light Module Bracket Light Module and Bracket Light Module Bracket Light Module Locknut, 1/4-20 Screw, 1/4-20 X 1-1/2 1098rev0813 Page 7A 5K804...
- Page 11 LED Lamp and Harness Installation 1. Install the inner Light Brackets on the frame tube, approximately 32” from the center of the frame. Place a Strap under the frame and secure Light Brackets with 1/2-13 X 7-1/2 Screws, Washers and Locknuts. See pages 7A and 7C. 2.
- Page 12 LED Warning Light Installation Light Module Bracket Light Screw,1/4-20 X 1-3/4 Screw, Shield Light 1/4-20 X 1-1/2 Bracket Decal Plate Locknut,1/4-20 Amber Screw, Light 5/8-11 X 8 Screw, Module Washer,1/4 1/4-20 X 1-1/2 7 Pin Washer,5/8 Harness Lamp Harness Nut,5/8-11 Washer,1/2 Lock Washer,5/8 Screw,...
- Page 13 ASSEMBLY OF THE 5K977 TIRE TRACK REMOVER KIT Screw ½”-13 X 8” Channel Adapter S-Tine Bracket 8” Strap Clamp 5” Strap Screw Screw 7/16”-14 X 3 ½” ½”-13 X 6” Screw ½”-13 X 1½” 7/16”-14 ½”-13 Lock Nut ½” Lockwasher Hex Nut Cultivator Bolt...
-
Page 14: Optional Equipment
PULVERIZERS MACHINE SPECIFICATIONS (Subject to Change without Notification) Model Designation: Basic model is denoted by “PPD” - Pickup Pulverizer with Ductile wheels. The number following indicates the rolling width. (example: PPD10 - 10’ Pickup Pulverizer with ductile wheels) Basic Machine Specifications: Rolling Transport 20”... - Page 15 Table provided for general use. NOTES:...
- Page 16 Page 10 1098ev401 5K804...
- Page 17 FRAME & ROLLER ASSEMBLY MACHINES WITH 4" OUTSIDE DIAMETER PIPE AXLE (10’ thru 16’ Machines) Index Part # Description Qty. Weight (lbs.) 5K726 Frame Tube, 10’ 306.9 5K727 Frame Tube, 12’ 361.8 5K728 Frame Tube, 14’ 416.8 5K729 Frame Tube, 16’ 471.7 9J028 Wheel and Axle Assembly (10’...
- Page 18 Page 12 1098ev401 5K804...
- Page 19 FRAME & ROLLER ASSEMBLY MACHINES WITH 4 1/2" OUTSIDE DIAMETER PIPE AXLE (18’ thru 20’ Machines) Index Part # Description Used Weight 5K730 Frame Tube, 18’ 531.3 5K731 Frame Tube, 20’ 586.2 3K323 Wheel and Axle Assembly (18’ Machines) 932.0 5K744 Wheel and Axle Assembly (20’...
- Page 20 3 Point Hitch PP10-20 Rep3PtHitch 1098rev0813 Page 14 5K804...
- Page 21 3 Point Hitch ITEM PART NUMBER DESCRIPTION QTY. 5K736 3 POINT HITCH 5D158 SLEEVE 5D110 KLIK PIN 1/4 X 1 -1/4 5D156 PIN ASSEMBLY 1-1/8 X 5-3/4 1-512-010007-11 NUT, HEX 5/8-11 GR2 ZP 1-861-010034-15 WASHER, LKG, HLCL SPR, 5/8 1-654-010059-21 SCREW, HEX CAP, 5/8-11UNC X 8 GR5 3K321 STRAP...
- Page 22 Page 16 1098ev401 5K804...
-
Page 23: Index
SCRAPERS Index Weight Part # Description Qt’y. (Lbs.) 5K753 Scraper Kit (10’Machines) 121.0 5K754 Scraper Kit (12’Machines) 137.0 5K755 Scraper Kit (14’Machines) 152.0 5K756 Scraper Kit (16’Machines) 168.0 5K757 Scraper Kit (18’Machines) 196.0 5K758 Scraper Kit (20’ Machines) 212.0 9J056 Scraper Tube - 124”... - Page 24 REAR 4K910 LIGHT KIT 07/31/2013 and Prior Index Weight Description Q’ty. (Lbs.) 4K772 Dual Lamp, L.H. 4K773 Dual Lamp, R.H. 4K908 Angle 4K854 Strap (18’-20’ Machines) 5C124 Machine Bolt, 1/2” x 7” (18’-20’ Machines) 3J561 Ubolt, 1/2” (10’-16’) 1C109 Lockwasher, 1/2” 1C390 Nut, 1/2-13 NC Hex 4K782...
- Page 25 Table provided for general use. NOTES:...
- Page 26 LED Warning Lights Page 18A 1098rev0813 5K804...
- Page 27 LED Warning Lights - 08/01/2013 and After ITEM PART NUMBER DESCRIPTION QTY. 178514 HARNESS, 7 PIN/4 PIN WP, 10’ 178513 HARNESS, LAMP 66 X 138 174437 MODULE, AG FLASHER CONTROL 178530 BRACKET, MODULE MNT, 6IN 1-654-010047-08 SCREW HX CP, 1/4-20UNCX1-1/2 G5 1-512-010005-01 NUT, HEX SLFLKG GRB 1/4-20 1-654-010047-09...
- Page 28 5K977 Wheel Track Remover Kit ITEM PART NUMBER DESCRIPTION 1J887 S-TINE, 10mm X 32mm 7D014 DUCKFOOT POINT 2J155 HEAVY DUTY REVERSIBLE POINT 7D728 CUL TIVATOR BOL T 5J616 FLANGE LOCK NUT 3/8-16 1-654-010055-17 SCREW,HEX CAP,1/2-13UNCX6 GR5 5J358 STRAP (5”) 1-861-010034-13 WASHER, LKG HLCL SPR, 1/2 1-512-010007-09 NUT, HEX 1/2-13 ZP...
- Page 29 PULVERIZERS SPECIAL NOTE ON OPTIMIZER MODELS Position Axle Clamps to outside ends & opposite Center Bearing 6K353 Optimizer Wheel Center Bearing Male & female The above diagram shows typical wheel gang positioning of optimizer model ends must pulverizers using optimizer wheels. Position of axle clamps is toward the mate outside end of the machine.
- Page 30 CONTENTS Introduction ............................3 Location Reference ........................3 Parts Ordering ..........................3 Safety Suggestions ........................... 4 Safety Signs ..........................4 Decal Location (Also See below for additional decal) ..............5 Operating Instructions ..........................6 Warning Light Assembly ........................... 7 Tire Track Remover Assembly ........................8 Machine Specifications ...........................
- Page 31 SPECIAL NOTE ON OPTIMIZER MODELS Position Axle Clamps to outside ends & opposite Center Bearing 6K353 Optimizer Wheel Center Bearing Male & female The above diagram shows typical wheel gang positioning of optimizer model ends must pulverizers using optimizer wheels. Position of axle clamps is toward the mate outside end of the machine.
- Page 32 (Subject to Change without Notification) MACHINE SPECIFICATIONS - PPO Models Model Designation: Basic model is denoted by “PPO” - Pickup Pulverizer with Optimizer wheels. The number following indicates the rolling width. (example: PPO10 - 10’ Pickup Pulverizer with Optimizer wheels) Basic Machine Specifications: Rolling Transport...
- Page 33 Table provided for general use. NOTES:...
- Page 34 Page 24 1098ev401 5K804...
- Page 35 FRAME TUBE with BRACKET ASSEMBLIES OPTIMIZERS WITH 4 1/2" OUTSIDE DIAMETER PIPE AXLE Index Part # Description Used Weight 5K726 Frame Tube, 10’ 306.9 5K727 Frame Tube, 12’ 361.8 5K728 Frame Tube, 14’ 416.8 5K729 Frame Tube, 16’ 471.7 5K730 Frame Tube, 18’...
- Page 36 OPTIMIZER MODELS WITH 20” OPTIMIZER WHEELS (P0T) Page 26 1098ev401 5K804...
- Page 37 OPTIMIZER MODELS WITH 20" OPTIMIZER WHEELS (POT) Index Part No. Used Per Machine Description 10’ 18’ 20’ Weight 6K481 Wheel & Axle Assembly 1112 6K485 Wheel & Axle Assembly 6K488 Wheel & Axle Assembly 6K490 Wheel & Axle Assembly 6K492 Wheel &...
- Page 38 INDEX Part Index Page Part Index Page Part Index Page 9C031 2J431 0A087 9C062 9C129 9C182 2J515 9C183 1B166 2J516 3J185 1D138 2D535 3J186 3D199 4D529 3J561 3J615 1C109 3J860 5D051 4J700 4J867 5D110 5J080 5D156 5J082 1C179 5D157 5J358 5D158 5J616 1C182...
- Page 39 Part Index Page Part Index Page Part Index Page 9J028 5K736 9J029 5K737 9J056 5K738 9J057 5K739 9J058 5K740 9J059 5K741 9J277 5K742 9J474 5K744 9J808 5K752 5K753 5K754 5K755 1K324 5K756 1K325 5K757 1K326 5K758 3K318 5K975 6K353 6K354 3K320 6K481 6K485...
- Page 40 5K804...
- Page 42 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Pick-up Pulverizer Operator’s and Parts Manual PPD Series 10’ through 20’ PPO Series 10’ through 20’ Re-Order Part Number 5K804 LANDOLL CORPORATION...