Advertisement
ASSEMBLY
Center Frame Tooth Control
Installation
Left Side
1. Attach a Tooth Control Bracket on the top of the left
Front Tooth Tube by sliding a Clamp Plate into the
Tooth Control Bracket Slot and under the Tooth Tube.
Secure with 5/8-11 x 5 Bolts and Locknuts. Do Not
tighten at this time. See Figures 2-33 and 2-34.
2. Lay the Cylinder Rod Clevis between the Tooth
Control Clamp Lugs. Position the Tooth Control Tube
over the top of the Cylinder Rod Clevis and between
the Tooth Control Bracket Lugs and insert a 1 x 6-1/2
Pin. Place a 1" Flat Washer on each side of the Pin
against the Tooth Control Bracket. Secure with 5/16 x
2 Roll Pins.
3. Position a Tooth Control Clamp w/cutout on top of the
left Rear Tooth Tube while straddling the Tooth
Control Tube. Insert 1 x 6-1/2 Pins. Place a 1" Flat
Washer on each side of the Pin against the Tooth
Control Clamp and secure with 5/16 x 2 Roll Pins.
Tooth Control Clamps should be aligned with each
other. Attach Tooth Control Clamp on the Tooth Tube
with two 5/8-11 x 5 Bolts and two 5/8-11 x 2 Bolts and
Locknuts.
4. Position a Tooth Control Bracket on top of the left
Middle Tooth Tube while straddling the Tooth Control
Tube. Insert 1 x 6-1/2 Pins. Place a 1" Flat Washer on
each side of the Pin against the Tooth Control Bracket
and secure with 5/16 x 2 Roll Pins. Attach Tooth
Control Clamps on Tooth Tube by sliding a Clamp
Plate into the Tooth Control Bracket Slot and under
the Tooth Tube. Secure with 5/8-11 x 5 Bolts and
Locknuts.
Right Side
1. Attach a Tooth Control Bracket on the top of the right
Front Tooth Tube by sliding a Clamp Plate into the
Tooth Control Bracket Slot and under the Tooth Tube.
Secure with 5/8-11 x 5 Bolts and Locknuts, Do Not
tighten at this time. See Figures 2-33 and 2-34.
2. Lay the Cylinder Rod Clevis between the Tooth
Control Bracket Lugs. Position the Tooth Control
Tube over the top of the Cylinder Rod Clevis and
between the Tooth Control Bracket Lugs and insert a
1 x 6-1/2 Pin. Place a 1" Flat Washer on each side of
the Pin against the Tooth Control Bracket. Secure
with 5/16 x 2 Roll Pins.
2-36
TABLE OF CONTENTS
3. Position a Tooth Control Bracket on top of the right
Rear Tooth Tube while straddling the Tooth Control
Tube. Insert 1 x 6-1/2 Pins. Place a 1" Flat Washer on
each side of the Pin against the Tooth Control Bracket
and secure with 5/16 x 2 Roll Pins. Attach Tooth
Control Brackets on Tooth Tube by sliding a Clamp
Plate into the Tooth Control Bracket Slot and under
the Tooth Tube. Secure with 5/8-11 x 5 Bolts and
Locknuts.
4. Position a Tooth Control Clamp w/cutout on top of the
right Middle Tooth Tube while straddling the Tooth
Control Tube. Insert 1 x 6-1/2 Pins. Place a 1" Flat
Washer on each side of the Pin against the Tooth
Control Clamp and secure with 5/16 x 2 Roll Pins.
Tooth Control Clamps should be aligned with each
other. Attach Tooth Control Clamp on the Tooth Tube
with two 5/8-11 x 5 Bolts and two 5/8-11 x 2 Bolts and
Locknuts.
Ensure that both linkages don't bind and the Tooth
Control Clamps and the Tooth Tubes are positioned
correctly. See Figure 2-32. Tighten the Bolts and Nuts at
this time.
F-982-0223
Advertisement
