Related Manuals for Landoll 2512 Series
Summary of Contents for Landoll 2512 Series
- Page 1 ® 2512 In-Row Ripper and Caddy Operators Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-1040-0320...
- Page 2 Manuals for the 2512 In-Row Ripper MANUAL NUMBER MANUAL NAME F-1039 2512 In-Row Ripper Parts Manual F-1040 2512 In-Row Ripper Operators Manual F-1075 Caddy Parts Manual (ONLY) F-1040-0320...
- Page 3 Table of Contents Introduction and Safety Information Understanding Safety Statements ..........1-2 Decal Safety .
- Page 4 TABLE OF CONTENTS F-1040-0320...
-
Page 5: Warranty
Introduction and Safety Information The Landoll Model 2512 Rigid & Folding In-Row Ripper is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation. -
Page 6: Introduction And Safety Information
TABLE OF CONTENTS INTRODUCTION AND SAFETY INFORMATION Understanding Safety Decal Safety Statements 1. Examine safety decals and be sure you have the correct safety decals for the implement. You will find various types of safety information on the 2. Keep these signs clean so they can be observed following pages and on the machine signs (decals) readily. -
Page 7: Maintenance Safety
TABLE OF CONTENTS INTRODUCTION AND SAFETY INFORMATION Maintenance Safety DANGER 1. Understand the procedure before doing the work. • Do not allow anyone to ride on the tractor or Use proper tools and equipment. implement. Riders could be struck by foreign 2. -
Page 8: Tire Safety
TABLE OF CONTENTS INTRODUCTION AND SAFETY INFORMATION Tire Safety Safety Chain 1. Tire changing can be dangerous and should be 1. Use a chain with a strength rating equal to or greater performed by trained personnel using correct tools than the gross weight of towed machinery, which is and equipment. -
Page 9: Model Specifications
Chapter 2 TABLE OF CONTENTS Standard Specifications Model Specifications 2511N Rigid In-Row Ripper Frame Model Number Number of Shanks Frame Type Transport Width Estimated Weight Configuration 3,357 W/2 GAUGE 2511N-3-30 RIGID 107 (IN) RIGID 110” (9’ - 2”) WHEEL 3,849 W/2 GAUGE 2511N-3-40 RIGID 107 (IN) RIGID... -
Page 10: Standard Specifications
TABLE OF CONTENTS STANDARD SPECIFICATIONS 2512 Folding In-Row Ripper (Caddy ONLY) Number of Estimated Model Number Shank Spacing Shank Extensions Transport Width Shanks Weight 17,097 W/2 210 (IN) CENTER 2512F-13-30 FOLDING - 3-7-3 227” (18’- 11”) GAUGE WHEEL CT (2) 82 (IN) WING ON WINGS 18,430 W/2 240 (IN) CENTER... - Page 11 TABLE OF CONTENTS STANDARD SPECIFICATIONS UNC SIZE SAE Grade 2 SAE Grade 5 SAE Grade 8 UNF SIZE SAE Grade 2 SAE Grade 5 SAE Grade 8 1/4-20 [11] 1/4-28 [12] 5/16-18 [10] [13] [22] 5/16-24 [11] [17] [25] 3/8-16 [19] [29] [42]...
-
Page 12: Hydraulic Fitting Torque Specifications
TABLE OF CONTENTS STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. - Page 13 TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-3: 4-Shank Spacing...
- Page 14 TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-4: 5-Shank Spacing F-1040-0320...
- Page 15 TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-5: 6-Shank Spacing...
- Page 16 TABLE OF CONTENTS STANDARD SPECIFICATIONS Figure 2-6: 7-Shank Spacing F-1040-0320...
- Page 17 TABLE OF CONTENTS STANDARD SPECIFICATIONS...
- Page 18 TABLE OF CONTENTS STANDARD SPECIFICATIONS 8-Shank Spacing 2-10 F-1040-0320...
- Page 19 Chapter 3 TABLE OF CONTENTS Assembly Instructions Specific Dangers and Warnings It is very important that your new 2512 Series Rigid or Folding In-Row Ripper be properly assembled, adjusted, and lubricated before use. Illustrations are provided in DANGER this section to show proper assembly procedures.
-
Page 20: Assembly Preparation
3/16 hair pin (See Figure 3-1.) HYDRAULIC RESET CYLINDER SMV EMBLEM SMV BRACKET HYDRAULIC ACCUMULATOR ID PLATE JACK STAND COULTER BLADES Figure 3-1: 2512 Series Parts Identification F-1040-0320... - Page 21 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Auto-Reset Clamp and Shank 1. Attach top of shank point assembly to front of spring clamp assembly using 3/4-10 x 4 hex head cap Assembly screw and hex lock nut. Attach lower hole of shank point assembly to rear of spring clamp assembly 1.
- Page 22 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS ROLL PIN GAPS PLACED OPPOSITE EACH OTHER Figure 3-2: Auto-Reset Clamp and Straight Leg Shank Assembly F-1040-0320...
- Page 23 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS SHANK EXTENSION Figure 3-3: Hydraulic Reset Option w/parabolic shank and coverboard...
- Page 24 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS RSB Clamp and Straight Shank 3. Attach steel point to low disturbance straight leg shank using 1/2 x 2 and 5/16 x 2 spring slotted pins. Assembly Place pins with open ends oriented opposite of each other.
-
Page 25: Gauge Wheel
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Coverboard Installation Right Hand & Left Hand Coulter Assemblies 1. Insert three 1/2-13 x 2-1/2 hex screws into the coverboard bracket before attaching the coverboard 1. Assemble coulter adjustment tube to coulter furrower (See Figure 3-3.) Secure with 1/2-13 nuts assembly using roll pins 1/2 x 4 and 5/16 x 4. - Page 26 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS RIPPLED BLADE PYRAMID BLADE LH ASSEMBLY EXPANDED VIEW SMOOTH BLADE RH ASSEMBLY Figure 3-6: Coulter Assembly F-1040-0320...
- Page 27 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS LH GAUGE WHEEL EXPANDED VIEW RH MOUNT (REMAINING COMPONENTS SAME AS LH GAUGE WHEEL) Figure 3-7: Gauge Wheel...
-
Page 28: Electrical Installation
TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Electrical Installation General Hydraulic Components - Hydraulic Reset Option 1. Attach left and right light brackets with reflectors to frame using warning light bar, 1/2-13 x 7-1/2 hex Figure 3-10 is provided as a general guideline for the head cap screws, and hex lock nuts (See components provided with the Hydraulic Reset Option. - Page 29 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Figure 3-8: LED Light and SMV Bracket Installation 3-11...
- Page 30 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS Figure 3-9: LED Light and SMV Harness Wire Designations 3-12 F-1040-0320...
- Page 31 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS ACCUMULATOR PRESSURE REDUCTION HOSE WRAP VALVE BALL VALVE HOSE CLAMP CLAMP PLATE COVER HOSE CLAMP BRACKET RH HOSE CLAMP MOUNT BRACKET LH HOSE CLAMP MOUNT BRACKET Figure 3-10: Hydraulic Reset Option - General Components 3-13...
- Page 32 TABLE OF CONTENTS ASSEMBLY INSTRUCTIONS 3-14 F-1040-0320...
- Page 33 DANGER Do not attempt to manually reset a shank assembly or straighten a bent shank mount. Contact a Landoll dealer or Landoll Corporation immediately for assistance. DANGER Never allow anyone to ride on the In-Row Ripper at any time.
-
Page 34: Operation And Maintenance
The pressure reduction valve is pre-set at the factory to have a hydraulic output of 2,000 psi. The pressure The 2512 Series Rigid and The Folding In-Row Rippers reduction valve will increase the hydraulic pressure of the up to and thru the 2512F-9 can be used on tractors with system to 2,000 psi if it is less than 2,000 psi and will CAT IVN hitches. -
Page 35: Attaching To Three-Point Hitch
TABLE OF CONTENTS OPERATION AND MAINTENANCE Attaching to Three-Point Hitch Attaching to Caddy 1. Carefully back the tractor into place. If you will be attaching the In-Row-Ripper to a Caddy: 2. Attach the In-Row Ripper to the tractor. 1. Carefully back the Caddy up to the In-Row-Ripper. 3. - Page 36 TABLE OF CONTENTS OPERATION AND MAINTENANCE 2512 RIGID FRAME 2511-N CAT II HITCH CAT III NARROW HITCH USED WITH 3, 4, & 5 NARROW FRAMES 4, 5, 6, 7 & 8 RIGID FRAMES 2512 RIGID FRAME 2511-N CAT III NARROW HITCH CAT III HITCH USED WITH 3, 4, &...
- Page 37 TABLE OF CONTENTS OPERATION AND MAINTENANCE Field Operation - Three Point 8. Tighten the slotted nut while rotating the hub until there is a slight resistance to wheel rotation. Back the Hitch Type slotted nut off one notch until the wheel rotates freely without end play.
- Page 38 TABLE OF CONTENTS OPERATION AND MAINTENANCE F-1040-0320...
- Page 39 The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 2512 Series Rigid & Folding In-Row Ripper. Follow all safety precautions stated in the previous sections when making any adjustments to your machine.
-
Page 40: Troubleshooting Guide
TABLE OF CONTENTS TROUBLESHOOTING GUIDE F-1040-0320... - Page 41 Document Control Revision Log: Date Form # New/Updated Improvement(s): Description and Comments 01/2020 F-1040 New manual released...
- Page 42 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. 2512 In-Row Ripper Operators Manual Re-Order Part Number F-1040-0320 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM ®...