Advertisement
TDSE1D, TDSE2D, TDSE1S2:
TDSE1RD, TDSE2RD:
TDSE1P, TDSE1RP, TDSE2P, TDSE2RP:
TDSE3, TDSE4:
RP:
DSE1-k, DSE2-k:
DSE1-a, DSE2-a:
DSE1-C, DSE2-C:
DSE1-kr, DSE2-kr:
DSE1-b, DSE2-b:
• Enter the numerical value and press the ENTER key.
• After setting, press the END key to display the following confirmation message.
C h a n g e s e t t i n g s ? Y = E N T E R / N = C A N C E L
• Press the ENTER (= Y) key to change settings and return to the "settings menu" screen.
Setting the NOC
To set the NOC setting, do the following.
• Select "NOC" on the "Group ∗ " screen to display the "NOC" screen.
S e t t i n g s - P r o t e c t i o n
G r o u p ∗ - N O C
N C 1 E N
M N C 1
M N C 1 C - I E C
M N C 1 C - I E E E
M N C 1 C - U S
N C 1 R
N C 1 - 2 F
N C 1
T N C 1 D # # # . # # s # # # . # # s N C 1 - a
# . # # #
T N C 1 P
T N C 1 R D # # # . # s
T N C 1 R P # . # # #
<<Scheme switch>>
<NC∗EN>
To set the NC ∗ enable, do the following.
• Enter "On" to enable the NC ∗ and press the ENTER key. If disabling the NC ∗ , enter "Off"
and press the ENTER key.
<MNC1>
To set the NC 1 time delay characteristic type, do the following.
• Enter "DT" or "IEC" or "IEEE" or "US" or "CON" and press the ENTER key.
0.0 - 300.0
0.00 - 300.00
0.00 – 100.00W (5A rating) 0.00 – 20.00W (1A rating)
0.000 - 30.000
0.00 - 5.00
0.000 - 5.000
0.000 - 30.000
0.00 - 5.00
∗ ∗ ∗
∗ ∗ ∗
N C 2 E N
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
N C 2 - 2 F
∗ ∗ ∗
∗ ∗ ∗
N C 2
∗ ∗ ∗
∗ ∗ ∗
T N C 2
∗ ∗ ∗
∗ ∗ ∗
∗ ∗ ∗
∗ ∗ ∗
∗ ∗ ∗
∗ ∗ ∗
# . # A
# . # A
N C 1 - k
# . # # #
N C 1 - C
# # # . # s
N C 1 - k r
# . # # #
N C 1 - b
⎯
⎯
197
0.00 - 300.00
0.010 - 1.500
2 5 / F e b / 2 0 0 3 0 9 : 4 5
∗ ∗ ∗
∗ ∗ ∗
∗ ∗ ∗
∗ ∗ ∗
# . # Α
# . # A
# # # . # # s # # # . # # s
# # . # # #
# # . # # #
# . # #
# . # #
# . # # #
# . # # #
# # . # # #
# # . # # #
# . # #
# . # #
6 F 2 S 0 8 4 2
Advertisement
