Advertisement
S e t t i n g s - P r o t e c t i o n
G r o u p ∗ - D S E F
D S E 4 E N
D S E 4 - D I R
D S E 4 - 2 F
D S E 4 - T P 1
D S E 4 - T P 2
D S E 4 - T P 3
D S E 4 - T P 4
D S E 4 - T P 5
D S E 4 - T P 6
R P E N
S e t t i n g s - P r o t e c t i o n
G r o u p ∗ - D S E F
D S E 1 - k
D S E 1 - a
D S E 1 - C
D S E 1 - k r
D S E 1 - b
D S E 2 - k
D S E 2 - a
D S E 2 - C
D S E 2 - k r
D S E 2 - b
( ∗ 1 ) : "DSE ∗ -TP ∗ " is only displayed if the model is GRD150-300 or 400 series.
<<Scheme switch>>
<DSE∗EN>
To set the DSE ∗ enable, do the following.
• Enter "On" to enable the DSE ∗ and press the ENTER key. If disabling the DSE ∗ , enter "Off"
and press the ENTER key.
<DSE∗-DIR>
To set the DSE ∗ directional characteristic, do the following.
• Enter "FWD" or "REV" and press the ENTER key.
<MDSE∗>
To set the DSE ∗ time delay characteristic type, do the following.
• Enter "DT" or "IEC" or "IEEE" or "US" or "CON" and press the ENTER key.
∗ ∗ ∗ ∗ ∗ ∗
D S E 4
∗ ∗ ∗ ∗ ∗ ∗
T D S E 4 # # # . # # s # # # . # # s
∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗
∗ ∗ ∗
R P
# # . # # # # # . # # #
# . # #
# . # #
# . # # #
# . # # #
# # . # # # # # . # # #
# . # #
# . # #
# # . # # # # # . # # #
# . # #
# . # #
# . # # #
# . # # #
# # . # # # # # . # # #
# . # #
# . # #
⎯
⎯
195
2 5 / F e b / 2 0 0 3 0 9 : 4 5
4 / 5
# . # # # Α
# . # # # A
# # # . # # W # # # . # # W
2 5 / F e b / 2 0 0 3 0 9 : 4 5
5 / 5
6 F 2 S 0 8 4 2
( ∗ 1 )
Advertisement
