Feature Commands; Regulatory Commands - Rice Lake REVOLUTION 682 Synergy Plus Technical Manual

12.13 Feature Commands

The following commands can be used to configure feature parameters.
Command
PWD.USER
PWD.SETUP
DATEFMT
DATESEP
TIMEFMT
TIMESEP
CONSNUM
CONSTUP
UID
KYBDLK
ZERONLY
CONTACT.COMPANY
CONTACT.ADDR1-3
CONTACT.NAME1-3
CONTACT.PHONE1-3
CONTACT.EMAIL
CONTACT.LASTCAL
CONTACT.NEXTCAL
KHOLDTIME
KHOLDINTERVAL
LOCALE
LAT.LOC
ELEV.LOC
DEST.LAT.LOC
DEST.ELEV.LOC
GRAV.LOC
DEST.GRAV.LOC
PERSISTENTTARE
REMOTE.PRINTDESTINATION
LANGUAGE

12.14 Regulatory Commands

The following commands can be used to configure regulatory parameters.
Command
REGULAT
AUDAGNCY
REG.SNPSHOT
REG.ZTARE
REG.KTARE
REG.MTARE
REG.NTARE
NTEP defaults shown for regulatory command values
Table 12-13. Feature Commands
Description
Sets user menu password; cannot query the current password
Sets setup menu password, cannot query the current password
Date format
Date separator
Time format
Time separator
Consecutive numbering
Consecutive number start-up value
ID of the indicator
Keyboard lock, disables keyboard except for the menu and
power key
Disables keyboard except for the zero, menu and power keys
Contact company name
Contact company address
Contact names
Contact phone numbers
Contact email address
Last calibration date
Next calibration date
Key hold time (in tenths of a second); 20 equals 2 seconds
Key hold time interval; the amount of time between increments
during a key hold (in twentieths of a second); 2 equals a tenth of
a second (10 increments per second during a key hold)
Enable gravity compensation
Origin latitude (to nearest degree) for gravity compensation
Origin elevation (in meters) for gravity compensation
Destination latitude (in degrees) for gravity compensation
Destination elevation (in meters) for gravity compensation
Origin gravity factor (in m/s
) for gravity compensation
2
Destination gravity factor (in m/s ) for gravity compensation
2
Determines if a tare remains through a power cycle
Determines whether the remote (another indicator) or local (682)
indicator prints when the print key is pressed on the remote
Sets the text language; applies to Weigh mode only
Table 12-14. Regulatory Commands
Description
Regulatory mode
Audit Agency (Industrial Mode)
Display or Scale weight source
Remove tare on ZERO
Always allow keyed tare
Multiple tare action
Allow negative tare
Up to 16 alphanumeric characters
Up to 16 alphanumeric characters
MMDDYY (default), DDMMYY, YYMMDD, YYDDMM
SLASH (default), DASH, SEMI, DOT
12HOUR (default), 24HOUR
COLON (default), COMMA, DOT
0–9999999, 0 (default)
0–9999999, 0 (default)
Up to 6 alphanumeric characters, 1 (default)
OFF (default), ON
OFF (default), ON
Up to 30 alphanumeric characters
Up to 20 alphanumeric characters (for each line)
Up to 30 alphanumeric characters (for each line)
Up to 20 alphanumeric characters (for each line)
Up to 40 alphanumeric characters
Date MMDDYYYY as an 8-digit number
Date MMDDYYYY as an 8-digit number
10–50, 20 (default)
1–100, 2 (default)
OFF (default), ON, FACTOR
0–90, 45 (default)
-9999–9999, 345 (default)
0–90, 45 (default)
-9999–9999, 345 (default)
9.00000–9.99999, 9.80665 (default)
9.00000–9.99999, 9.80665 (default)
OFF (default), ON
REMOTE (default), LOCAL
ENGLISH (default), SPANISH, FRENCH,
GERMAN, DUTCH, PORTUGUESE, ITALIAN
NTEP (default), CANADA, INDUST, NONE, OIML
NTEP (default), CANADA, NONE, OIML
DISPLAY (default), SCALE
NO (default), YES
NO, YES (default)
REPLACE (default), REMOVE, NOTHING
NO (default), YES
© Rice Lake Weighing Systems ● All Rights Reserved
EDP Commands
Values
Values
91