Mitsubishi A1SD75P1-S3 User Manual page 607

Axis error occurrence time (Second: 100 ms)
( Md.22 ) ......................................................... 5-88
Axis error reset ( Cd.12
Axis feedrate ( Md.37 ) .................................. 5-96
Axis in which the error occurred (
Axis in which the warning occurred (
....................................................................... 5-90
Axis monitor data........................................... 5-92
Axis operation status ( Md.35
Axis stop signal ............................................. 3-15
Axis warning No. (
Md.25
Axis warning detection .................................. 5-98
Axis warning occurrence time (Hour: minute)
( Md.26 ) ......................................................... 5-90
Axis warning occurrence time (Second: 100 ms)
( ) ......................................................... 5-90
Md.27
[B]
BACKLASH COMPENSATION
(explanation of terms) ......................Appendix-28
BACKUP FUNCTION (explanation of terms)
..........................................................Appendix-28
BALL SCREW (explanation of terms)
..........................................................Appendix-28
BIAS SPEED AT START (explanation of terms)
..........................................................Appendix-29
BIPOLAR DRIVE CONSTANT-CURRENT
SYSTEM (explanation of terms) ......Appendix-29
BUSY (explanation of terms) ...........Appendix-29
BUSY signal .................................................. 3-13
Backlash compensation amount (
Backlash compensation function ................ 12-11
Basic parameters 1 ....................................... 5-18
Basic parameters 2 ....................................... 5-24
Bias speed at start ( Pr.10
Block .............................................................. 10-8
Block No. being executed (
Block start (normal start) ............................... 10-8
Block transmission ........................................ 7-13
Block transmission area.................................. 7-3
Buffer memory................................................. 7-2
Buffer memory area configuration .................. 7-5
[C]
CCW (explanation of terms) ............Appendix-29
CHANGE signal (explanation of terms)
..........................................................Appendix-29
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
) ............................. 5-112
) .... 5-88
Md.19
)
Md.24
)...................... 5-94
, Md.34 ) .......... 5-90,94
) ... 5-28
Pr.12
) ......................... 5-25
Md.55 )............ 5-104
Index - 2
CIRCULAR INTERPOLATION
(explanation of terms) ...................... Appendix-29
COMMAND PULSE (explanation of terms)
.......................................................... Appendix-29
COMPOSITE SPEED (explanation of terms)
.......................................................... Appendix-29
CONTINUOUS POSITIONING CONTROL
(explanation of terms) ...................... Appendix-29
CONTROL UNIT (explanation of terms)
.......................................................... Appendix-29
CP CONTROL (explanation of terms)
.......................................................... Appendix-29
CPU module.....................................................2-5
CREEP SPEED (explanation of terms)
.......................................................... Appendix-30
CURRENT FEED VALUE (explanation of terms)
.......................................................... Appendix-30
CURRENT LOOP MODE (explanation of terms)
.......................................................... Appendix-30
CURRENT VALUE (explanation of terms)
.......................................................... Appendix-30
CURRENT VALUE CHANGE
(explanation of terms) ...................... Appendix-30
CW (explanation of terms)............... Appendix-30
CW/CCW mode .............................................5-22
Cable clamp ...................................................4-10
Cable fixture ...................................................4-13
Clock data (hour: minute) (
Clock data (second: 100 ms) (
Clock data function ......................................13-11
Clock data setting (hour) (
Clock data setting (minute, second) (
......................................................................5-106
Clock data setting program............................6-14
Clock data writing ( Cd.3
Combination of AD75 functions.....................3-10
Combination of main functions and auxiliary
functions .........................................................3-10
Command in-position flag..............................5-98
Command in-position function.....................12-72
Command in-position width (
Command pulse frequency .............................1-9
Command speed ( Da.7
Common functions.................................. 3-9,13-1
Communicating signals between AD75 and each
module............................................................1-10
Composite speed...........................................5-34
Condition data..............................................10-17
Md.5 ) ...............5-82
Md.6 ) .........5-82
) ..............5-106
Cd.1
Cd.2 )
) .........................5-106
)............5-30
Pr.17
) ............................5-68