SoftBank Whiz Operational Manual page 16

Whiz Operational Manual
DISCLAIMER
SOFTBANK ROBOTICS CORP. ("COMPANY") DISCLAIMS ANY AND ALL LIABILITY ARISING FROM
THE USE OF THIS DOCUMENT AND DOES NOT GUARANTEE THAT ANY INFORMATION CONTAINED
HEREIN IS ACCURATE OR COMPLETE.
THIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO THE COMPANY AND MAY NOT BE
REPRODUCED, TRANSMITTED, OR DISTRIBUTED IN WHOLE OR PART, IN ANY FORM OR BY ANY
MEANS, WITHOUT THE EXPRESS WRITTEN PERMISSION OF THE COMPANY.
THIS BOOK EXPRESSES THE AUTHOR'S VIEWS AND OPINIONS. THE INFORMATION CONTAINED IN
THIS BOOK IS PROVIDED WITHOUT ANY EXPRESS, STATUTORY, OR IMPLIED WARRANTIES.
IN NO EVENT SHALL THE COMPANY, ITS RESELLERS, DISTRIBUTORS OR SUPPLIER BE LIABLE TO
YOU OR ANY OTHER PARTY FOR ANY DIRECT, INDIRECT, GENERAL SPECIAL, INCIDENTAL,
CONSEQUENTIAL, EXEMPLARY OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PRODUCT (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR INJURY, LOSS OF
PROPERTY, BUSINESS PROFITS, BUSINESS INTERRUPTION) OR FROM ANY BREACH OF
WARRANTY, EVEN IF THE COMPANY, ITS RESELLERS, DISTRIBUTORS OR SUPPLIER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO CASE SHALL OUR COMPANY, ITS
RESELLERS, DISTRIBUTORS OR SUPPLIER'S LIABILITY EXCEED THE AMOUNT YOU PAID FOR THE
PRODUCT.
■ FCC Compliance Statement
The Whiz Vacuum and the Notification Pager comply with part 15 of the FCC rules.
Note with respect to the Whiz Vacuum:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
This equipment (FCC ID: 2AT19-A00000101A01) complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance requirements. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Note with respect to the Notification Pager:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This pager device (FCC ID: 2AT19-P00000401A01) is designed to meet the requirements for exposure to
radio waves established by the Federal Communications Commission (USA). These requirements set an SAR
limit for an occupational/controlled environment of 0.4 W/kg, as averaged over the whole body, and a peak
spatial average SAR of 8 W/kg, averaged over any 1 gram of tissue. The highest SAR value reported under
this standard during product certification for use when properly worn on the body is 0.06 W/kg. This device was
tested for typical body-worn operations with a separation of 10mm from the body. To maintain
15 / 145