SoftBank Whiz Quick Manual
Hide thumbs
Also See for Whiz:
- Operational manual (147 pages) ,
- Operation manual (123 pages) ,
- Manual (15 pages)
Advertisement
Quick Links
Whiz Quick Guide
Introduction
This document contains information on the daily use of the Machine. Please read and understand the
contents of the Whiz Operational Manual before using the Machine. The latest version of this document
and the Whiz Operational Manual can be found on "Whiz Connect".
For the latest Whiz Operational Manual and this document,
please check out Whiz Connect: https://whiz.softbankrobotics.com
*Login with ID / Password.
1.Names of Parts
Front / Side
Top
Vacuum Power
■
Button
2.Before Teaching a Cleaning Route
Before teaching a cleaning route to the Machine,
stick the Home Location Code (HLC) at a permanent
location where autonomous cleaning will start / stop
(flat against a wall or a pillar).
If the HLC needs to be moved, place it at the
same location whenever the Machine runs autonomously.
Please note that cleaning may not be performed correctly
if the installation of HLC is slightly off.
Whiz Connect
2D/3D Camera
■
(Sensor)
Dustbin
■
Pager holder
■
LIDAR Sensor
■
Emergency Stop Button
■
Touch Display
■
Steering Handle
■
Max Power Mode Button
■
Autonomous Clean
■
Start/Stop Button
Back
HEPA Filter
■
(Inside the cover)
Main Power Switch
■
Battery
■
(Inside the Battery Compartment)
Bottom
Cliff Sensor
■
Brush
■
Hopper Tray
■
Secondary Battery
■
Power Button
80cm (2.6ft)
2020.04
60cm (2.0ft)
1
Advertisement
Related Manuals for SoftBank Whiz
Summary of Contents for SoftBank Whiz
- Page 1 Whiz Quick Guide 2020.04 Introduction This document contains information on the daily use of the Machine. Please read and understand the contents of the Whiz Operational Manual before using the Machine. The latest version of this document and the Whiz Operational Manual can be found on "Whiz Connect". Whiz Connect For the latest Whiz Operational Manual and this document, please check out Whiz Connect: https://whiz.softbankrobotics.com *Login with ID / Password. 1.Names of Parts Front / Side Back 2D/3D Camera ■ HEPA Filter ■ (Sensor) (Inside the cover) Dustbin ■ Main Power Switch ■ Pager holder ■ Battery ■ LIDAR Sensor ■ (Inside the Battery Compartment) Bottom Cliff Sensor ■ Emergency Stop Button ■...
- Page 2 3.Teaching a Cleaning Route Move the Machine to the Pull the the Steering Handle Press the Main power switch Home Location Code straight up until you reach the to turn it on ( l ) joint and tilt the handle to lock it into position 80cm (2.6ft) 60cm (2.0ft) Scan the Home Location Code Select "+" to create a new Tap "TEACH ROUTE" route If an error is displayed in a red frame, For each Home Location Code, six adjust the distance of the Machine and cleaning routes can be saved. the code and scan it again. Clean the entire teaching route Once cleaning is complete, Press the Vacuum Power Button press the Vacuum Power Even if you pause during Button and turn the cleaning teaching, it will not affect the mode off cleaning when carried out autonomously. Please clean at your own pace. Backward movements will not be recognised ・Use the cleaning modes (Normal mode / Max power mode) according to the condition of the floor. as a cleaning route. ・The switch between two cleaning modes will be duplicated during autonomous cleaning. Tap "Save Route," scan the Recharge the battery HLC again Pull out the battery from the Machine, and recharge it in the charger. ...
- Page 3 4.Carrying Out Autonomous Cleaning Select a cleaning route to carry out autonomous cleaning. Operate in a time when there are few passerby and objects around the cleaning area. For safety, the Machine will operate slightly away from the wall. When cleaning areas close to the wall, operate manually. Scan the Home Location Tap "RUN ROUTE" Select the Cleaning Route Code If an error is displayed in a red frame, adjust the distance of the Machine and the code and scan it again. Press the Autonomous Clean Tap "OK" Stow the Steering Handle Start/ Stop Button ・Remove the Notification Pager from the Machine and carry it with you during autonomous cleaning. Routes that have completed cleaning is shown ・Once cleaning is complete, the Machine will return Hold the handle with both hands, and raise it in blue and routes that have not completed to the Home Location Code and the Pager will forward at an angle. Then, push it back in to cleaning is shown in white. notify the operator of the completion of cleaning. its original position. 5.Machine Maintenance【Every day ~ every week】 Dustbag Replace every 9 hours approx If the error message is displayed when the dustbag is full, replace it with a new dustbag. The recommended replacement period is approximately every 9 hours (3 hours a day, 3 days a week). 2.Remove the dustbag 3.Hook it to the dustbin Pin 1.Open the dustbin 4.Push it in firmly 5.Check the dustbin Pin is afloat Hold the dustbin Access Handle Pull out the attachment sheet Ensure that the illustration Align the suction port and the If the dustbag is installed ...
- Page 4 6.Machine Maintenance【Once in a half year】 Brush HEPA Filter If the bristle of the Brush If the HEPA filter is dirty, is getting shorter, replace repalce it with a new filter. it with a new one. Do not wash with water. 7.Machine Stops Moving During Autonomous Cleaning The machine stops moving when it has left the cleaning route or detects obstacles. Check the environment the machine operates, and move it to an appropriate place as required. If an error screen is displayed, please follow the instructions on the touch display and touch in the upper right corner. Close curtains to block light in a Wipe the sensors with the Adjust the brightness in a place place where there is sunlight attached Micro-fiber cloth where there are lights or LED lights 2D/3D Camera (Sensor) LIDAR Sensor When an error occurs several times in When the machine has left the When the change of the layout takes areas where there are reflective objects cleaning route, follow the instructions place after teaching the cleaning route, such as automatic doors, avoid those recreate the original layout on the display areas and teach a new cleaning route Carrying Out × Teaching Cleaning Route Autonomous Cleaning Automatic doors Window glass Return the machine to the cleaning route, ...