Table of Contents
Advertisement
Index
Reference Sample Hold ..........................................................83
Relay Operator Control ..........................................................97
Removing the Cooling Fan .................................................... 176
Replacement Parts .............................................................. 171
Replacing the Drive ............................................................ 188
Reset Communication Parameters..............................................71
Response Messages from Drive to Master .................................. 290
Restart Enabled ...................................................................94
Reverse Jog ........................................................................81
Reverse Operation Selection ....................................................19
Reverse Run Command for 2-Wire Seq. ......................................84
RS-422 Interface ................................................................ 284
RS-485 Interface ................................................................ 283
RTS Control Selection ......................................................... 286
Run Command at Power Up.....................................................20
Run Command for 2-Wire Seq. 2...............................................84
Run Command Method Selection ............................................ 287
RUN Command Selection for AUTO mode ................................ 195
Run Command Selection for AUTO Mode ...................................17
Run Command Selection in Programming Mode ............................20
Run Command Source ...........................................................91
Run Command Source Selection ............................................. 254
Rx to Tx Wait Time ..............................................................74
S
S: Special Parameters .................................................... 141, 239
S1: Dynamic Noise Control Function........................................ 239
S2: Sequence Timers ..................................................... 142, 239
S5: HOA Keypad Parameters ................................................. 156
Safety Circuit.................................................................... 150
S-Curve Characteristics ..........................................................47
Search Operation Voltage Limit ................................................45
Secondary PI (PI2) Control.................................................... 146
Secondary PI Disable Mode............................................. 148, 242
Secondary PI Display Digits ............................................ 147, 241
Secondary PI Enable Selection ......................................... 146, 241
Secondary PI Feedback Detection Selection .......................... 149, 242
Secondary PI Feedback High ...................................................97
Secondary PI Feedback Low ....................................................96
Secondary PI High Feedback Detection Time ........................ 149, 242
Secondary PI High Feedback Level .................................... 149, 242
Secondary PI Integral Limit Setting.................................... 148, 242
Secondary PI Integral Time Setting .................................... 147, 242
Secondary PI Low Feedback Detection Level ........................ 148, 242
Secondary PI Low Feedback Detection Time ........................ 149, 242
Secondary PI Output Level Selection .................................. 148, 242
Secondary PI Output Lower Limit ..................................... 148, 242
Secondary PI Output Upper Limit...................................... 148, 242
Secondary PI Proportional Gain Setting ............................... 147, 242
Secondary PI Setpoint Value............................................ 147, 242
Secondary PI Unit Selection ............................................ 147, 241
Secondary PI User Display ........................................ 146, 241, 243
Second Line Monitor Selection ............................................... 134
Selection of Parameter Write during Uv..................................... 238
Select PI2 Parameters ............................................................87
Self-Diagnostics...................................................................85
Sequence Timer 1............................................................... 142
Sequence Timer 1 Active ........................................................96
Sequence Timer 1 Day Selection ............................................. 239
Sequence Timer 1 Reference Source......................................... 239
320
Sequence Timer 1 Selection................................................... 239
Sequence Timer 1 Start Time ................................................. 239
Sequence Timer 1 Stop Time ................................................. 239
Sequence Timer 2 Active ........................................................96
Sequence Timer 2 Day Selection ............................................. 240
Sequence Timer 2 Reference Source......................................... 240
Sequence Timer 2 Selection................................................... 240
Sequence Timer 2 Start Time ................................................. 240
Sequence Timer 2 Stop Time ................................................. 240
Sequence Timer 3 Active ........................................................96
Sequence Timer 3 Day Selection ............................................. 240
Sequence Timer 3 Reference Source......................................... 240
Sequence Timer 3 Selection................................................... 240
Sequence Timer 3 Start Time ................................................. 240
Sequence Timer 3 Stop Time ................................................. 240
Sequence Timer 4 Active ........................................................96
Sequence Timer 4 Day Selection ............................................. 241
Sequence Timer 4 Reference Source......................................... 241
Sequence Timer 4 Selection................................................... 241
Sequence Timer 4 Start Time ................................................. 240
Sequence Timer 4 Stop Time ................................................. 241
Sequence Timer Cancel ..........................................................85
Sequence Timer Disable .........................................................85
Sequence Timers 1/2/3/4 Reference Source................................. 145
Sequence Timers 1/2/3/4 Selection........................................... 145
Sequence Timers 1 to 4 Day Selection....................................... 145
Sequence Timers 1 to 4 Start Time........................................... 144
Sequence Timers 1 to 4 Stop Time ........................................... 144
Sequence Timers 2 to 4 ........................................................ 143
Serial Comms Cable Connection Terminal ................................. 282
Serviceable Parts................................................................ 188
Set Time.......................................................................... 238
Slave Address ................................................................... 291
SMRA Series SPM Motor Settings .......................................... 263
Soft Charge Bypass Relay Maintenance..................................... 253
Soft CLA Selection ............................................................. 232
Soft Starter Speed Reference at Previous Fault............................. 250
Software Current Limit Selection ............................................ 126
Software No. (Flash) ........................................................... 249
Software No. (ROM) ........................................................... 249
SoH Alarm Selection during bb............................................... 128
Speed Agree 1 .....................................................................89
Speed Agree 2 .....................................................................92
Speed Agree Detection Level ................................................. 116
Speed Agree Detection Level (+/-) ........................................... 117
Speed Agree Detection Selection............................................. 117
Speed Agree Detection Width ................................................ 116
Speed Agree Detection Width (+/-) .......................................... 117
Speed Agreement Detection Level ........................................... 230
Speed Agreement Detection Level (+/-) ..................................... 230
Speed Agreement Detection Width .......................................... 230
Speed Agreement Detection Width (+/-) .................................... 231
Speed Feedback Detection Control Gain .............................. 131, 234
Speed Search Deceleration Time ...............................................25
Speed Search Delay Time .......................................................25
Speed Search Detection Compensation Gain .................................26
Speed Search Induced Voltage Level ..........................................27
Speed Search Method Selection ................................................27
Speed Search Method Switching Level (Speed Estimation Type) .........26
Speed Search Restart Current Level............................................26
YASKAWA ELECTRIC SIEP C710636 10C Z1000U HVAC MATRIX Drive Programming Manual
Advertisement
Table of Contents
