Table of Contents
Advertisement
Output Voltage Reference (Vq)............................................... 255
Overcurrent Detection Gain ............................................. 126, 232
Overexcitation Deceleration................................................... 114
Overexcitation Deceleration Gain ...................................... 130, 234
Overheat Alarm Level......................................................95, 232
Overheat Pre-Alarm Operation Selection ...............................96, 232
Overtorque Detection Operation.............................................. 121
Overvoltage Suppression Function ........................................... 115
P
Parameters Changed with Motor Code Selection (PM Motors) .......... 263
Password and Password Setting ................................................12
Peak Hold Current .............................................................. 253
Peak Hold Output Frequency ................................................. 253
Performance Life ............................................................... 171
Performance Life Monitors Maintenance Monitors........................ 171
Periodic Inspection ............................................................. 169
Periodic Maintenance .......................................................... 171
Phase Order Selection ............................................................20
Phase Order Selection (Emergency Override Reference Selection) ..... 159
Phase Order Selection (Emergency Override Speed) ...................... 159
PI2 Disable (N.O.) ................................................................86
PI2 Integral Hold..................................................................87
PI2 Integral Reset .................................................................87
PI2 Inverse Operation ............................................................87
PID Accel/Decel Time ...........................................................38
PID Block Diagram...............................................................34
PID Control........................................................................31
PID Disable........................................................................82
PID Feedback ................................................................... 254
PID Feedback Function Selection ..............................................40
PID Feedback High...............................................................95
PID Feedback High Detection Level...........................................41
PID Feedback High Detection Time ...........................................41
PID Feedback Input Methods ...................................................32
PID Feedback Loss Detection Selection.......................................37
PID Feedback Low ...............................................................95
PID Feedback Low Detection Level ...........................................37
PID Feedback Low Detection Time............................................37
PID Feedback Offset .............................................................40
PID Fine Tuning ..................................................................43
PID Function Setting .............................................................35
PID Input (feedback) ........................................................... 254
PID Input Level Selection .......................................................84
PID Input Limit ...................................................................41
PID Integral Hold .................................................................84
PID Integral Reset ................................................................84
PID Maximum Boost Time......................................................40
PID Monitors .................................................................... 164
PID Offset Adjustment...........................................................35
PID Output....................................................................... 254
PID Output 2 Monitor Max Upper/Lower 4 Digits ..........................42
PID Output 2 Monitor Minimum ...............................................42
PID Output Gain Setting.........................................................36
PID Output Level Selection .....................................................36
PID Output Limit .................................................................35
PID Output Lower Limit.........................................................41
PID Output Monitor Calculation Method .....................................42
PID Output Reverse Selection ..................................................36
PID Output Reverse Selection 2 ................................................43
YASKAWA ELECTRIC SIEP C710636 10C Z1000U HVAC MATRIX Drive Programming Manual
PID Primary Delay Time Constant .............................................35
PID Setpoint ..................................................................... 254
PID Setpoint Boost Setting ......................................................40
PID Setpoint Display Digits.....................................................41
PID Setpoint Input Methods.....................................................32
PID Setpoint Monitor Unit Selection ..........................................42
PID Setpoint Scaling .............................................................39
PID Setpoint Selection ...........................................................38
PID Setpoint User Display ......................................................41
PID Setpoint Value ...............................................................39
PID Sleep ..........................................................................38
PID Sleep Delay Time ...........................................................38
PID Sleep Function Start Level .................................................38
PID Sleep Input Source ..........................................................39
PID Snooze Deactivation Level ................................................40
PID Snooze Delay Time .........................................................39
PID Snooze Feedback Level ....................................................40
PID Snooze Level.................................................................39
PID Soft Starter Cancel ..........................................................84
PID Square Root Gain ...........................................................40
PID Unit Selection................................................................41
PI Integral Reset ..................................................................87
PM Motor Auto-Tuning Mode Selection .................................... 161
PM Motor Base Frequency .................................................... 162
PM Motor Code ...................................................................64
PM Motor Code Selection ..................................................... 161
PM Motor Control Tuning..................................................... 130
PM Motor d-Axis Inductance ................................................. 162
PM Motor Induced Voltage Constant ........................................ 163
PM Motor q-Axis Inductance ................................................. 162
PM Motor Rated Current ...................................................... 162
PM Motor Rated Power........................................................ 161
PM Motor Rated Voltage ...................................................... 162
PM Motor Stator Resistance .................................................. 162
PM Motor Type ................................................................. 161
Power Consumption Output Unit Selection ...................................97
Power consumption pulse output ...............................................95
Power Detection Filter Time ....................................................44
Power Factor Control Selection.................................................51
Power Unit Price ................................................................ 140
Predefined V/f Patterns ..........................................................58
Previous Fault ................................................................... 250
PROFIBUS-DP Clear Mode Selection ........................................73
PROFIBUS-DP Data Format Selection........................................73
PROFIBUS-DP Node Address .................................................73
PROFIBUS-DP Parameters .....................................................73
Program Lockout .................................................................82
Programmable Bypass Logic.................................................. 150
Programmable Run Timers for Real Time Clock (RTC).................. 142
Proportional Gain Setting (P) ...................................................35
Pull-In Current ............................................................ 131, 234
Pull-In Current Compensation Time Constant.............................. 234
Pull-In Current Level for PM Motor Tuning................................ 163
R
Rated Current Depending on Carrier Frequency .............................50
READ ............................................................................ 138
Reading Drive MEMOBUS/Modbus Register Contents .................. 293
Real Time Clock ................................................................ 142
Real Time Clock Setting....................................................... 139
Index
319
Advertisement
Table of Contents
