Page 1 MX10008 Universal Routing Platform Hardware Guide Published 2019-11-11...
Page 2 END USER LICENSE AGREEMENT The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use with) Juniper Networks software. Use of such software is subject to the terms and conditions of the End User License Agreement (“EULA”) posted at https://support.juniper.net/support/eula/.
Page 3: Table Of Contents
Software on MX10008 | 30 MX10008 Components and Configurations | 31 MX10008 Component Redundancy | 33 MX10008 Hardware and CLI Terminology Mapping | 33 MX10008 Chassis | 35 MX10008 Chassis Physical Specifications | 36 Field-Replaceable Units in an MX10008 | 38...
Page 4 Fan Trays | 45 Fan Tray Controller | 48 Airflow Direction in the MX10008 Router | 51 MX10008 Fan Tray LEDs and Fan Tray Controller LEDs | 52 Fan Tray LEDs | 52 Fan Tray Controller LEDs | 57 MX10000 Power System | 59...
Page 5 Power Requirements for an MX10008 Router | 100 Calculating the Power Consumption of Your MX10008 Configuration | 101 Calculating the Number of Power Supplies Required for Your MX10008 Configuration | 102 JNP10K-PWR-AC Power Specifications | 105 JNP10K-PWR-AC2 Power Specifications | 106...
Page 6 Installing the Mounting Hardware | 140 Installing the MX10008 into a Rack | 143 Mounting an MX10008 in a 4-Post Rack Using a Mechanical Lift | 143 Manually Mounting an MX10008 in a 4-Post Rack | 147 Installing the Front Panel on an MX10008 | 151...
Page 7 Maintain the Fiber-Optic Cables in a Router | 271 Removing the MX10008 Router | 272 Powering Off an MX10008 Router | 272 Removing an MX10008 Router From a Four-Post Rack Using a Mechanical Lift | 275 Manually Removing an MX10008 Router from a 4-Post Rack | 276...
Page 8 Locating the Serial Number ID Labels on MX10008 Power Supplies | 300 Locating the Serial Number ID Labels on MX10008 Fan Trays and Fan Tray Controllers | 303 Locating the Serial Number ID Labels on MX10008 Routing and Control Boards | 303...
Page 9 Action to Take After an Electrical Accident | 343 Prevention of Electrostatic Discharge Damage | 343 AC Power Electrical Safety Guidelines | 345 AC Power Disconnection Warning | 346 DC Power Electrical Safety Guidelines for MX10008 Router | 346 DC Power Disconnection Warning | 348...
Page 10 Israel | 361 Japan | 362 Korea | 362 United States | 362 Nonregulatory Environmental Standards | 362 Compliance Statements for Environmental Requirements | 363 MX10008 Compliance Statements for Acoustic Noise | 363 MX10016 Compliance Statements for Acoustic Noise | 363...
Page 11 If the information in the latest release notes differs from the information in the documentation, follow the product Release Notes. Juniper Networks Books publishes books by Juniper Networks engineers and subject matter experts. These books go beyond the technical documentation to explore the nuances of network architecture, deployment, and administration.
Page 12 If the example configuration contains the top level of the hierarchy (or multiple hierarchies), the example is a full example. In this case, use the load merge command. If the example configuration does not start at the top level of the hierarchy, the example is a snippet. In this case, use the load merge relative command.
Page 13: Documentation Conventions
xiii Merging a Snippet To merge a snippet, follow these steps: 1. From the HTML or PDF version of the manual, copy a configuration snippet into a text file, save the file with a name, and copy the file to a directory on your routing platform. For example, copy the following snippet to a file and name the file ex-script-snippet.conf.
Page 14 Table 1: Notice Icons Icon Meaning Description Informational note Indicates important features or instructions. Caution Indicates a situation that might result in loss of data or hardware damage. Warning Alerts you to the risk of personal injury or death. Laser warning Alerts you to the risk of personal injury from a laser.
Page 15 Table 2: Text and Syntax Conventions (continued) Convention Description Examples Italic text like this Represents variables (options for Configure the machine’s domain which you substitute a value) in name: commands or configuration [edit] statements. root@# set system domain-name domain-name Text like this Represents names of configuration To configure a stub area, include statements, commands, files, and...
Page 16: Documentation Feedback
URL or page number, and software version (if applicable). Requesting Technical Support Technical product support is available through the Juniper Networks Technical Assistance Center (JTAC). If you are a customer with an active Juniper Care or Partner Support Services support contract, or are...
Page 17 JTAC hours of operation—The JTAC centers have resources available 24 hours a day, 7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features: Find CSC offerings: https://www.juniper.net/customers/support/...
Page 18: Mx10008 System Overview
MX10008 System Overview | 21 MX10008 Chassis | 35 MX10008 Cooling System | 44 MX10000 Power System | 59 MX10008 Routing and Control Board Components and Descriptions | 77 MX10008 Switch Fabric Board | 83 Line card (MX10K-LC2101) | 87...
Page 20: Mx10008 Hardware Overview
MX10008 Power Supplies | 28 Software on MX10008 | 30 Juniper Networks MX10008 Universal Routing Platform enables cloud and data center operators to transition from 10-Gigabit Ethernet and 40-Gigabit Ethernet networks to 100-Gigabit Ethernet high-performance networks. The 13 rack unit (13 U) modular chassis can provide 19.2 Tbps of throughput...
Page 21: Benefits Of The Mx10008 Router
20 Bpps of forwarding capacity. The MX10008 router has eight slots for the line cards that can support a maximum of 768 10-Gigabit Ethernet ports, 192 40-Gigabit Ethernet ports, or 192 100-Gigabit Ethernet ports. The MX10008 universal router provides 2.4 Tbps per slot fabric capacity for the service providers and cloud operators.
Page 22 Chassis Description MX10008 is 13 U tall. Up to three MX10008 routers can fit in a standard 39 U rack with adequate cooling and power. All key MX10008 router components are field-replaceable units (FRUs). Figure 1 on page 23 illustrates the key components visible from the front of the chassis.
Page 23 Figure 2: MX10008 Chassis Rear FAN FTC SIB STATUS FAN FTC SIB STATUS AC or DC power supplies Fan trays with redundant fans — — Figure 3 on page 25 illustrates the components that are internal to the chassis.
Page 24: Mx10008 Routing And Control Board
The Routing and Control board (RCB) (see Figure 4 on page 26) contains a Routing Engine and is responsible for the system management and control in the MX10008. See “MX10008 Routing and Control Board Description” on page 77. RCBs are FRUs that are installed in the front of the chassis in the slots labeled CB0 and CB1.
Page 25: Mx10008 Line Card (Mx10K-Lc2101)
Figure 4: MX10008 Routing and Control Board MX10008 Line Card (MX10K-LC2101) MX10008 has eight horizontal line card slots and supports line rate for each line card. The line cards combine a Packet Forwarding Engine and Ethernet interfaces enclosed in a single assembly. The MX10008 line card architecture is based on a number of identical, independent Packet Forwarding Engine slices each with 400 Gbps full-duplex throughput.
Page 26: Cooling System
When all the six SFBs are installed, the MX10008 router has a net switching capacity of 2.4 terabytes per second (bidirectional). “MX10008 Switch Fabric Board Description” on page...
Page 27: Mx10008 Power Supplies
Power supplies for the MX10008 router are fully redundant, load-sharing, and hot-removable and hot-insertable FRUs. Each MX10008 router with a base configuration has three power supplies; redundant configurations hold a maximum of six AC, high-voltage alternating current (HVAC), DC, or high-voltage direct current (HVDC) power supplies.
Page 28 Figure 9: JNP10K-PWR-AC Power Supply Figure 10: JNP10K-PWR-AC2 Power Supply Figure 11: JNP10K-PWR-DC Power Supply...
Page 29 The Juniper Networks MX10008 router runs on Junos OS, which provides Layer 3 routing services. The same Junos OS code base that runs on MX10008 router also runs on all Juniper Networks M Series, MX Series, and T Series routers and SRX Series Services Gateways.
Page 30: Mx10008 Components And Configurations
MX10008 Components and Configurations Table 4 on page 31 lists the four hardware configurations for an MX10008 modular chassis—base (AC and DC versions), and redundant (AC and DC versions)—and the components included in each configuration. Table 4: MX10008 Hardware Configurations...
Page 31 RCBs for your router configuration, you must order them separately. SEE ALSO MX10008 Cooling System and Airflow | 45 MX10008 Routing and Control Board Description | 77 JNP10K-PWR-AC Power Supply | 61 JNP10K-PWR-DC Power Supply | 65 MX10008 Switch Fabric Board Description | 84...
Page 32: Mx10008 Component Redundancy
MX10008 Component Redundancy The MX10008 router is designed so that no single point of failure can cause the entire system to fail. The following major hardware components in the redundant configuration provide redundancy: Routing and Control Board (RCB)—The RCB consolidates the Routing Engine function with the control plane function in a single unit.
Page 33: Mx10008 Chassis
Table 5: CLI Equivalents of Terms Used in Documentation for MX10008 Routers Hardware Item In Item (CLI) Description (CLI) Value (CLI) Documentation Additional Information Chassis JNP10008 – Router chassis “MX10008 Chassis [MX10008] Physical Specifications” on page 36 Routing and CB (n) n is a value in the range “MX10008 Routing and...
Page 34: Mx10008 Status Panel Leds
Table 5: CLI Equivalents of Terms Used in Documentation for MX10008 Routers (continued) Hardware Item In Item (CLI) Description (CLI) Value (CLI) Documentation Additional Information SFB (n) This field indicates: n is a value in the range Fabric plane show chassis fabric sfb of 0–5.
Page 35 The MX10008 modular chassis is a rigid sheet-metal structure that houses the other router components. You can mount up to three MX10008 routers in a standard 19-in. 4-post rack (42 U) rack provided the rack can handle the combined weight and there is adequate power and cooling.
Page 36 Do not use the handles to lift the chassis, even when the chassis is empty. See “Mounting an MX10008 in a 4-Post Rack Using a Mechanical Lift” on page 143 “Manually Mounting an MX10008 in a 4-Post Rack” on page 147 for instructions for properly moving a loaded chassis.
Page 37 Hot-pluggable—You can remove and replace these components without powering off the router, but the routing function is interrupted until you replace the component. Table 7 on page 38 lists the FRUs and their types for the MX10008 routers. Table 7: FRUs in an MX10008 Router Type Power supplies Hot-insertable and hot-removable.
Page 38 OS release in which the transceivers were introduced. NOTE: If you have a Juniper Care service contract, register any addition, change, or upgrade of hardware components at https://www.juniper.net/customers/support/tools/updateinstallbase/. Failure to do so can result in significant delays if you need replacement parts. This note does not apply if you replace an existing component with the same type of component.
Page 39 Figure 15 on page 40). Figure 15: Status Panel on Chassis with the Enhanced Power Bus Table 8 on page 40 describes the status panel LEDs. Table 8: Status Panel LEDs in an MX10008 Router Name Color State Description Power supplies...
Page 40 Table 8: Status Panel LEDs in an MX10008 Router (continued) Name Color State Description Fans Green On steadily The fans and the fan tray controllers are online and operating normally. Yellow On steadily There is an error in a fan or in one of the fan tray controllers.
Page 41: Mx10008 Optional Equipment
JNP10K-PWR-AC Power Supply | 61 JNP10K-PWR-DC Power Supply | 65 MX10008 Optional Equipment The MX10008 router supports the cable management system as an optional equipment. The cable management system (see Figure 16 on page 43) enables you to route optical cables away from the line card ports for better airflow through the chassis.
Page 42 Figure 16: Cable Management System The cable management system comprises a set of handle extensions and a tray that snaps to the extensions (see Figure 17 on page 43) for an individual line card. The handle extensions can be used with or without the cable tray.
Page 43: Mx10008 Cooling System
MX10008 Cooling System and Airflow | 45 MX10008 Fan Tray LEDs and Fan Tray Controller LEDs | 52 The MX10008 cooling system components work together to keep all components within the acceptable temperature range. If the maximum temperature specification is exceeded and the system cannot be...
Page 44: Mx10008 Cooling System And Airflow
Fan Tray Controller | 48 Airflow Direction in the MX10008 Router | 51 The cooling system in an MX10008 chassis consists of two fan trays and two fan tray controllers, which are hot-insertable and hot-removable field replaceable units (FRUs). There are two cooling system configurations available: JNP10008-FAN and JNP10008-FAN-CTRL—Designed to support the standard or enhanced power bus...
Page 45 Figure 19: Installed JNP10008-FAN, with JNP10K-PWR-AC Power Supplies in an MX10008 Router FAN FTC SIB STATUS FAN FTC SIB STATUS Power supplies Fan trays — —...
Page 46 Figure 20: Installed JNP10008-FAN2, with JNP10K-PWR-AC2 Power Supplies in an MX10008 Router Power supplies Fan trays — — Table 9 on page 47 for the physical specifications for the fan trays. Table 9: Fan Tray Specifications Specification JNP10008-FAN JNP10008-FAN2 Corresponding fan tray controller...
Page 47: Fan Tray Controller
Table 9: Fan Tray Specifications (continued) Specification JNP10008-FAN JNP10008-FAN2 Depth 4.0 in. (10.2 cm) without handles, 5.5 in. (13.97 cm) without handles, 5.2 in. (13.2 cm) with handles 6.7 in. (17.01 cm) with handles Weight 11.8 lb (5.4 kg) 20 lb (9.07 kg) If you want to replace an existing fan tray while the router is running, remove only one fan tray.
Page 48 Figure 22: Fan Controller JNP10008-FTC2 The system continually monitors the temperature of critical parts across the chassis and adjusts the chassis fan speed according to the temperature. Software controls the fan speed. Under normal operating conditions, the fans in the fan tray run at less than full speed.If one fan tray controller fails or appears missing (such as when an SFB is being replaced) the other fan tray controller sets the fans to full speed.
Page 49 The following is similar output from a JNP10008-FAN2 and JNP10008-FTC2 system: user@host> show chassis fan Item Status Measurement Fan Tray 0 Fan 0 6450 Spinning at normal speed Fan Tray 0 Fan 1 7950 Spinning at normal speed Fan Tray 0 Fan 2 6450 Spinning at normal speed Fan Tray 0 Fan 3...
Page 50: Airflow Direction In The Mx10008 Router
1.5 lb (0.68 kg) 1.1 lb (0.5 kg) Airflow Direction in the MX10008 Router The air intake to cool the chassis is located on the port (line card) side of the chassis. Air flows into the chassis from the ports in the RCBs and line cards, through the switch fabric boards (SFBs), and exits from the fan trays and the power supplies.
Page 51: Mx10008 Fan Tray Leds And Fan Tray Controller Leds
You can check the status of fans by viewing the LEDs on each fan tray. See “MX10008 Fan Tray LEDs and Fan Tray Controller LEDs” on page You cannot replace a single fan. If one or more fans fail, you must replace the entire fan tray.
Page 52 See Figure 25 on page 53.for the location of LEDs on the JNP10008-FAN2 fan tray. Figure 24: Fan Tray JNP10008-FAN LEDs on an MX10008 Router Fan status LED SFB status (SFB 0 through SFB 2 for the left fan tray —...
Page 53 Table 11 on page 54 describes the functions of the fan tray LEDs. Table 11: Fan Tray LEDs on an MX10008 Router Name Color State Description Fan status Green On steadily All fans are operating normally. The system has verified that the fan tray is engaged, that the airflow is in the correct direction, and that all fans are operating correctly.
Page 54 Table 11: Fan Tray LEDs on an MX10008 Router (continued) Name Color State Description SFB 0 status Green On steadily The left-most SFB in the chassis is online. Green Blinking The beacon feature is enabled. This feature is enabled using the request chassis beacon command.
Page 55 Table 11: Fan Tray LEDs on an MX10008 Router (continued) Name Color State Description SFB 2 status Green On steadily The right-most SFB behind the left fan tray is online. Green Blinking The beacon feature is enabled. This feature is enabled using the request chassis beacon command.
Page 56: Fan Tray Controller Leds
Table 11: Fan Tray LEDs on an MX10008 Router (continued) Name Color State Description SFB 4 status Green On steadily The center SFB behind the right fan tray is online. Green Blinking The beacon feature is enabled. This feature is enabled using the request chassis beacon command.
Page 57 Fan tray controller power Fan tray controller status — — Table 12 on page 58 describes the functions of the fan tray controller LEDs. Table 12: Fan Tray Controller LEDs on an MX10008 Router Name Color State Description Fan controller power...
Page 58: Mx10000 Power System
Table 12: Fan Tray Controller LEDs on an MX10008 Router (continued) Name Color State Description Fan tray controller status Green On steadily The fan tray controller is online and is operating normally. Green Blinking The beacon feature is enabled. This feature is enabled using the request chassis beacon command.
Page 59 All of the power supplies are hot-insertable and hot-removable, field-replaceable units (FRUs). You can install up to six power supplies in an MX10008 router in the slots labeled PEM 0 through PEM 5 (top to bottom) located in the rear of the chassis. In the MX10016, you can install up to 10 power supplies in the slots labeled PEM 0 through PEM 9 (top to bottom) located in the rear of the chassis.
Page 60: Jnp10K-Pwr-Ac Power Supply
Using a grounding cable with an incorrectly attached lug can damage the router. The base configuration MX10008 routers are shipped with three power supplies; base configuration MX10016 routers are shipped with five power supplies. Cover panels are installed over the remaining power supply slots.
Page 61 require in a 2n configuration. Should one power source fail, ATS routes the power supply to the alternate source. NOTE: For redundancy, always plug the two power cords from each power supply: INP1 into a UPS INP2 into the public electricity supply Each JNP10K-PWR-AC power supply has a power switch with international markings for on (|) and off (O), a fan, and four LEDs on the faceplate that indicate the status of the power supply.
Page 62: Jnp10K-Pwr-Ac2 Power Supply
Figure 28: Power Cord Retainer for an JNP10K-PWR-AC Power Supply Each power supply connects to the power rail in the router. The power rail distributes the output power produced by the power supplies to different router components. Each power supply provides power to all the components in the router.
Page 63 The JNP10K-PWR-AC2 fits into the standard power supply bay but when compared to most other models, the JNP10K-PWR-AC2 is longer and protrudes from the bay when fully inserted into the chassis. See Figure 29 on page Figure 29: Comparision of the JNP10K-PWR-AC2 to the JNP10K-PWR-AC Power Supply WARNING: Extreme burn danger–Do not handle an HVAC or HVDC power supply running in the chassis without heat protective gloves, such as welder’s gloves.
Page 64: Jnp10K-Pwr-Dc Power Supply
“MX10008 Status Panel LEDs” on page JNP10K-PWR-DC Power Supply MX10008 routers support three types of DC power supply modules: JNP10K-PWR-DC—A 2500-W, 12-VDC dual power supply. JNP10K-PWR-DC2—A 5500-W, 12-VDC quad input power supply. For details on this power supply, “JNP10K-PWR-DC2 Power Supply” on page JNP10K-PWR-AC2—An AC, high-voltage alternating current (HVAC,) or high-voltage direct current...
Page 65 NOTE: DC power supplies are shipped only in the redundant configuration of MX10000 routers. For details about different chassis configurations, see “MX10008 Components and Configurations” on page 31 and MX10016 Components and Configurations.
Page 66 JNP10K-PWR-DC power supplies can use the standard power bus or the enhanced power bus. All MX10016 chassis ship with the enhanced power bus; to determine whether an MX10008 has the standard or enhanced power bus, see “MX10008 Status Panel LEDs” on page Each JNP10K-PWR-DC power supply weighs approximately 6 lb (2.7 kg) and has two independent pairs...
Page 67: Jnp10K-Pwr-Dc2 Power Supply
Each power supply connects to the combined power rail in an MX10000 router. The power rail distributes the output power produced by the power supplies to different router components. Each DC power supply provides power to all the components in the router. NOTE: Route all the DC power supply cords away from the fan trays.
Page 68 DC and HVDC can coexist in the same chassis during the hot swap of DC for HVDC. All MX10016 router chassis have the enhanced power bus; to determine whether an MX10008 has the standard or enhanced power bus, see “MX10008 Status Panel LEDs”...
Page 69: Jnp10K-Pwr-Ac Power Supply Leds
Using a grounding cable with an incorrectly attached lug can damage the router. NOTE: DC power supplies are shipped only in the redundant configuration of MX10008 routers. For details about different chassis configurations, see “MX10008 Components and Configurations”...
Page 70 If the INP1 or INP2 LED is lit and the PWR OK LED is unlit, the AC power supply is not installed properly or the power supply has an internal failure. SEE ALSO JNP10K-PWR-AC Power Specifications | 105 Power Requirements for MX10008 Components MX10000 Power Cables Specifications | 107 Connecting AC Power to an MX10000 | 163...
Page 71: Jnp10K-Pwr-Ac2 Power Supply Leds
JNP10K-PWR-AC2 Power Supply LEDs The JNP10K-PWR-AC2 power supply has four LEDs on its faceplate: !, OK, 2, and 1. These LEDs display information about the status of the power supply. See Figure 34 on page Figure 34: LEDs on a JNP10K-PWR-AC2 HVDC Power Supply ! FAULT 2 INP2–Source input 1 —...
Page 72: Jnp10K-Pwr-Dc Power Supply Leds
Table 18: Interpreting JNP10K-PWR-AC2 LEDs Color State Description INP1 or INP0 in CLI output Yellow Blinking The input voltage is present, but is not within normal operating range. Green Solid The input voltage is present and within normal operating range. Unlit The power supply is switched off;...
Page 73 — INP2–Source input 1 FAULT — — Table 19 on page 74 describes the LEDs in an MX10008. Table 19: LEDs on a DC Power Supply in an MX10008 Color State Description INP1 or INP2 Yellow Blinking Indicates that the DC power input voltage is not within normal operating range.
Page 74: Jnp10K-Pwr-Dc2 Power Supply Leds
If the FAULT LED is blinking, add a power supply to balance the power demand and supply. SEE ALSO JNP10K-PWR-DC Power Specifications | 115 Power Requirements for MX10008 Components Connecting DC Power to an MX10000 | 164 JNP10K-PWR-DC2 Power Supply LEDs A JNP10K-PWR-DC2 power supply module has four LEDs on its faceplate: 1, 2, OK, and the symbol for fault, !.
Page 75 Table 20 on page 76 describes the LEDs on a JNP10K-PWR-DC2 power supply. Table 20: LEDs on a JNP10K-PWR-DC2 Power Supply Color State Description 1 (INP0 in CLI output) or 2 Yellow Blinking Indicates that the DC power input voltage is not (INP1 in CLI output) within normal operating range.
Page 76: Mx10008 Routing And Control Board Components And Descriptions
IN THIS SECTION Routing and Control Board Functions | 78 Routing and Control Board Components | 79 The MX10008 Routing and Control Board (RCB) is responsible for system management in an MX10008 router (see Figure 37 on page 78). The chassis can run with one or two RCBs. The base configuration ships with one RCB while a redundant configuration ships with two RCBs.
Page 77: Routing And Control Board Functions
Figure 37: Routing and Control Board JNP10K-RE1-128 JNP10K-RE1-128 MASTER This topic covers: Routing and Control Board Functions The Routing and Control Board (RCB) integrates the control plane and Routing Engine functions into a single management unit. Each RCB provides all the functions needed to manage the operation of the modular chassis: System control functions such as environmental monitoring Routing Layer 2 and Layer 3 protocols...
Page 78: Routing And Control Board Components
Routing and Control Board Components Figure 38: Routing and Control Board Faceplate Handles Reset button — — BITS1 clock port Online/Offline button — — GPS clock ports USB port — — XGE-0 and XGE-1 JCS ports Management (MGMT) ports — —...
Page 79: Mx10008 Routing And Control Board Leds
For specific information about Routing Engine components (for example, the amount of DRAM), issue the show vmhost hardware command. SEE ALSO Handling and Storing MX10008 Line Cards, RCBs, and SFBs | 244 Installing a Routing and Control Board | 176 MX10008 Routing and Control Board LEDs Figure 39 on page 81 shows the LEDs on the Routing and Control Boards (JNP10K-RE1).
Page 80 Figure 39: Routing and Control Board LEDs Routing and Control Board status panel Clock LEDs–BITS-0, and BITS-1 — — Solid State Disk (SSD) LEDs—DISK1 and DISK2 — Table 21 on page 81 describes the LEDs on the RCB status panel. Table 21: Routing and Control Board Status LEDs Color State...
Page 81 — indicates activity (SFP) Activity LED (RJ-45) — Table 22 on page 82 describes the RJ-45 management port and SFP LEDs. Table 22: RJ-45 Management Port LEDs on an MX10008 Routing and Control Board Color State Description Activity/Status Unlit The port speed is 10 MB.
Page 82: Mx10008 Switch Fabric Board
Table 23: JCS Port LEDs on an MX10008 Routing and Control Board Color State Description LINK LEDs for Unlit No transceiver is present. JCS Ports (XGE0 and Green On steadily A link is established. The interface is up. XGE1) Green Blinking or flickering The beacon feature is enabled.
Page 83: Mx10008 Switch Fabric Board Description
RCBs in the front and the fan trays in the rear. When all six SFBs are installed, the MX10008 has a net switching capacity of 42 terabytes. MX10008 Switch Fabric Board Description The SFBs make up the switching plane.
Page 84 Table 25: Dimensions of an MX10008 SFB (continued) Specification Value Depth 10.4 in. (26.42 cm) Weight 14.8 lb (6.71 kg) SFBs are hot-removable and hot-insertable field-replaceable units (FRUs). They are not visible from the outside of the router chassis. You must remove one of the fan trays in order to view the SFBs. The SFBs are numbered from left to right SFB0 to SFB5.
Page 85: Mx10008 Switch Fabric Board Leds
MX10008 Switch Fabric Board LEDs The Switch Fabric Board (SFB) has two status LEDs at the top of each board. See Figure 43 on page Figure 43: SFB LEDs Table 26 on page 86 describes the functions of these LEDs.
Page 86: Line Card (Mx10K-Lc2101)
The MX10K-LC2101 line card is a fixed configuration MPC and it does not contain separate slots for Modular Interface Cards (MICs). The MX10008 routers support eight MX10K-LC2101 MPCs.The line card provides a maximum bandwidth of 2.4Tbps and has six Packet Forwarding Engines, each providing a maximum bandwidth of up to 400 Gbps.
Page 87 Cables and TIP: You can use the Hardware Compatibility Tool to find information about the pluggable transceivers supported connectors on your Juniper Networks device. The list of supported transceivers for the MX Series is located at MX Series Supported Transceivers.
Page 88: Site Planning, Preparation, And Specifications
C HAPTER Site Planning, Preparation, and Specifications MX10008 Site Preparation Overview | 91 MX10008 Power Planning | 100 MX10008 Transceiver and Cable Specifications | 118 MX10008 Alarm and Management Cable Specifications and Pinouts | 125...
Page 90: Mx10008 Site Preparation Overview
MX10008 Environmental Requirements and Specifications | 92 General Site Guidelines | 94 Site Electrical Wiring Guidelines | 94 MX10008 Rack Requirements | 96 MX10008 Clearance Requirements for Airflow and Hardware Maintenance | 98 MX10008 Site Preparation Checklist The checklist in Table 27 on page 91 summarizes the tasks you need to perform when preparing a site for an MX10008 installation.
Page 91: Mx10008 Environmental Requirements And Specifications
Mounting an MX10008 in a 4-Post Rack Using a Mechanical Lift | 143 Manually Mounting an MX10008 in a 4-Post Rack | 147 MX10008 Environmental Requirements and Specifications The MX10008 router must be installed in a four-post rack. It must be housed in a dry, clean, well-ventilated, and temperature-controlled environment.
Page 92 Follow these environmental guidelines: The site must be as dust-free as possible, because dust can clog air intake vents and filters, reducing the efficiency of the router cooling system. Maintain ambient airflow for normal router operation. If the airflow is blocked or restricted, or if the intake air is too warm, the router might overheat, leading to the router temperature monitor shutting down the device to protect the hardware components.
Page 93: General Site Guidelines
NOTE: Install MX10008 router only in restricted areas, such as dedicated equipment rooms and equipment closets, in accordance with Articles 110-16, 110-17, and 110-18 of the National Electrical Code, ANSI/NFPA 70. General Site Guidelines This topic applies to hardware devices in the MX10008 routers.
Page 94 CAUTION: It is particularly important to provide a properly grounded and shielded environment and to use electrical surge-suppression devices. Table 29: Site Electrical Wiring Guidelines Site Wiring Factor Guideline Signaling limitations To ensure that signaling functions optimally: Install wires correctly. Improperly installed wires can emit radio interference.
Page 95: Mx10008 Rack Requirements
OSP wiring SEE ALSO General Site Guidelines | 94 MX10008 Rack Requirements The MX10008 router chassis are designed to be installed in four-post racks. Rack requirements consist of: Rack type Mounting bracket hole spacing...
Page 96 Table 30: Rack Requirements for the MX10008 Rack Requirement Guidelines Rack type: four-post Use a four-post rack that provides bracket holes or hole patterns spaced at 1 U (1.75 in. or 4.45 cm) increments and that meets the size and strength requirements to support the weight.
Page 97: Mx10008 Clearance Requirements For Airflow And Hardware Maintenance
Manually Mounting an MX10008 in a 4-Post Rack | 147 MX10008 Clearance Requirements for Airflow and Hardware Maintenance When planning the site for an MX10008 router installation, you must allow sufficient clearance around the installed chassis for cooling and maintenance (see Figure 44 on page 99 for MX10008.
Page 98 Leave at least 24 in. (61 cm) both in front of and behind the MX10008 for service personnel to remove and install hardware components. To be NEBS GR-63 compliant, allow at least 30 in. (76.2 cm) in front of the rack and 24 in.
Page 99: Mx10008 Power Planning
MX10008 and plan your configuration’s power requirements. Power Requirements for an MX10008 Router Use the information in this topic to calculate power requirements of your MX10008 configuration and the number of power supplies required for different MX10008 router configurations.
Page 100: Calculating The Power Consumption Of Your Mx10008 Configuration
This topic describes these tasks: Calculating the Power Consumption of Your MX10008 Configuration | 101 Calculating the Number of Power Supplies Required for Your MX10008 Configuration | 102 Calculating the Power Consumption of Your MX10008 Configuration Use the following procedure to determine the maximum power you need to supply to the router. To calculate maximum system power consumption, you first determine the combined maximum internal power requirements of all the router components and then divide this result by the power supply output power.
Page 101: Calculating The Number Of Power Supplies Required For Your Mx10008 Configuration
8225 W 9975 W 9400 W 11400 W For example, for an MX10008 with eight MX10K-LC2101 line cards, the maximum power consumption @400 Gigabit Ethernet mode is: = 8* 1425 W= 11400 W 3. Add the power consumption from Step and the total line card consumption from Step 2.
Page 102 Table 33: Total Power Available (continued) With Three With Four With Five Power Power Supply Module Models Power Supplies Power Supplies Supplies JNP10K-PWR-AC2 dual feed, high power 16,500 W 22,000 W 27,500 W (30-A) setting JNP10K-PWR-AC2 single feed, high power 15,000 W 20,000 W 25,000 W...
Page 103 In the previous examples, we calculated that an MX10008 AC system would require 11800 W with eight line cards. In this example, we calculate the total power available for this configuration: = (14050 W) / (2700 W) = 5.20 Round up the result to 6 AC power supplies.
Page 104: Jnp10K-Pwr-Ac Power Specifications
JNP10K-PWR-DC Power Supply | 65 Power Requirements for MX10008 Components JNP10K-PWR-AC Power Specifications MX10008 and MX10016 redundant configuration router can use either AC or DC power supplies; base configuration routers are AC only. Table 35 on page 105 lists the power specifications for the AC power supply (JNP10K-PWR-AC) used in an MX10000 chassis.
Page 105: Jnp10K-Pwr-Ac2 Power Specifications
MX10000 Power Cables Specifications | 107 JNP10K-PWR-AC2 Power Specifications MX10008 and MX10016 redundant configuration router can use either AC or DC power supplies; base configuration routers are AC only. The JNP10K-PWR-AC2 power supply supports AC, HVAC, and HVDC. Table 37 on page 106 lists the power specifications for the AC power supply (JNP10K-PWR-AC) used in an MX10000 chassis.
Page 106: Mx10000 Power Cables Specifications
“JNP10K-PWR-AC2 Power Cable Specifications” on page 110 JNP10K-PWR-AC2 with 30-A input, see “JNP10K-PWR-AC2 Power Cable Specifications for 30-A Input” on page 113 JNP10K-PWR-AC Power Cable Specifications Table 39 on page 108 lists the AC power cord specifications for MX10008 routers for various countries and regions.
Page 107 Table 39: AC Power Cord Specifications for MX10008 Routers Electrical Juniper Model Country/Region Specifications Plug Standards Number Graphic Argentina 250 VAC, 16 A, IRAM Type RA/3/20 CBL-EX-PWR-C19-AR 50 Hz Australia 250 VAC, 15 A, AS/NZS 3112 Type CBL-EX-PWR-C19-AU 50 Hz...
Page 108 CBL-EX-PWR-C19-UK 50 Hz BS89/13 CAUTION: AC power cords for MX10008 routers are intended for use with these routers only. Do not use the cord for another product. Power Cable Warning (Japanese) WARNING: The attached power cable is only for this product. Do not use the cable for another product.
Page 109: Jnp10K-Pwr-Ac2 Power Cable Specifications
JNP10K-PWR-AC2 Power Cable Specifications The JNP10K-PWR-AC2 power supply operates in two modes: 30-A input with 5500 W output “JNP10K-PWR-AC2 Power Cable Specifications for 30-A Input” on page 113 shows cables and connectors for 30-A input. 20-A input with 3000 W output Table 40 on page 111 shows cables appropriate for 20-A input.
Page 110 Table 40: JNP10K-PWR-AC2 Power Cable Specifications for 20-A Input Spare Juniper Locale Cord Set Rating Plug Standards Model Number Graphic Argentina 16 A, 250 VAC IRAM 2073 Type CBL-JNP-SG4-AR RA/3 Australia and New 15 A, 250 VAC AS/NZS 4417 CBL-JNP-SG4-AU...
Page 111 Table 40: JNP10K-PWR-AC2 Power Cable Specifications for 20-A Input (continued) Spare Juniper Locale Cord Set Rating Plug Standards Model Number Graphic India 16 A, 250 VAC SANS 164/1 CBL-JNP-SG4-SA Israel 16 A, RA, 250 VAC SI 32/1971 Type CBL-JNP-SG4-IL IL/3G...
Page 112: Jnp10K-Pwr-Ac2 Power Cable Specifications For 30-A Input
JNP10K-PWR-AC2 orders. An example of the right-angle cable and connector is shown in Figure 47 on page 115. For connection to AC systems, Juniper provides a cable with either a NEMA 30-A connector (Figure 45 on page 113) or an IEC 330P6W connector (Figure 46 on page 113).
Page 113 Table 41: 30-A Cabling Options Cord Set Plug Spare Juniper Model Locale Rating Standards Connector Number HVAC/HVDC 30- A, UL 950 and Anderson/straight to CBL-PWR2-BARE power cord 400 VAC IEC 60950 bare wire HVAC/HVDC 30-A, UL 950 and Anderson/right-angle CBL-PWR2-BARE-RA...
Page 114: Jnp10K-Pwr-Dc Power Specifications
— Green wire-Ground — JNP10K-PWR-DC Power Specifications The DC power supply (JNP10K-PWR-DC) is supported in only the MX10008 and MX10016 redundant configuration. Table 42 on page 115 lists the power specifications for the JNP10K-PWR-DC power supply used in an MX10000 chassis.
Page 115: Jnp10K-Pwr-Dc2 Power Specifications
JNP10K-PWR-DC Power Supply | 65 JNP10K-PWR-DC Power Supply LEDs | 73 JNP10K-PWR-DC2 Power Specifications HVDC power supplies (JNP10K-PWR-DC2) are supported in only the MX10008 and MX10016 redundant configuration. Table 44 on page 116 lists the power specifications for the HVDC power supply used in a MX10000 chassis.
Page 116: Mx10008 Grounding Cable And Lug Specifications
(EMI) requirements. To ground an MX10008 chassis, connect a grounding cable to earth ground and then attach it to the chassis grounding point on the rear of the chassis beneath.
Page 117: Mx10008 Transceiver And Cable Specifications
This lug accommodates 4 AWG (21.1mm²) stranded wire. The grounding cable that you provide for an MX10008 must be the same size or heavier than the input wire of each power supply. Minimum recommendations are 6 AWG (13.3 mm²) stranded copper wire, Class B;...
Page 118: Mx10008 Optical Transceiver And Cable Support
MX10008 Optical Transceiver and Cable Support The MX10008 router has eight slots for the line cards that can support a maximum of 1152 ports as 10-Gigabit Ethernet ports, 288 ports as 40-Gigabit Ethernet ports, or 240 ports as 100-Gigabit Ethernet ports.
Page 119: Mx10008 Cable Specifications For Console And Management Connections
MX10008 Cable Specifications for Console and Management Connections Table 46 on page 120 lists the specifications for the cables that connect the MX10008 line of routers to a management device. NOTE: The MX10008 router can be configured with SFP management ports that support 1000BASE-SX transceivers.
Page 120: Signal Loss In Multimode And Single-Mode Fiber-Optic Cables
To determine the power budget and power margin needed for fiber-optic connections, you need to understand how signal loss, attenuation, and dispersion affect transmission. The MX10008 router uses various types of network cables, including multimode and single-mode fiber-optic cables. Signal Loss in Multimode and Single-Mode Fiber-Optic Cables Multimode fiber is large enough in diameter to allow rays of light to reflect internally (bounce off the walls of the fiber).
Page 121: Calculating The Fiber-Optic Cable Power Budget For An Mx10008 Router
2. Calculate the power budget (P ) by subtracting (P ) from (P –15 dBm – (–28 dBm) = 13 dBm SEE ALSO Understanding Fiber-Optic Cable Signal Loss, Attenuation, and Dispersion Calculating the Fiber-Optic Cable Power Margin for an MX10008 Router | 123...
Page 122: Calculating The Fiber-Optic Cable Power Margin For An Mx10008 Router
Calculating the Fiber-Optic Cable Power Margin for an MX10008 Router Calculate the link's power margin when planning fiber-optic cable layout and distances to ensure that fiber-optic connections have sufficient signal power to overcome system losses and still satisfy the minimum input requirements of the receiver for the required performance level.
Page 123 Table 47: Estimated Values for Factors Causing Link Loss (continued) Link-Loss Factor Estimated Link Loss Value Sample Link Loss (LL) Calculation Values Fiber attenuation Multimode—1 dBm/km This example assumes the link is 2 km long. Fiber attenuation for 2 km: 2 km (1 dBm/km) = 2 dBm. Single-mode—0.5 dBm/km This example assumes the link is 2 km long.
Page 124: Mx10008 Alarm And Management Cable Specifications And Pinouts
If your laptop or PC does not have a DB-9 male connector pin and you want to connect your laptop or PC directly to an MX10008 router, use a combination of the RJ-45 cable and RJ-45 to DB-9 adapter supplied with the device and a USB to DB-9 male adapter. You must provide the USB to DB-9 male adapter.
Page 125: Usb Port Specifications For The Mx10008 Router
Connecting an MX10008 Router to a Management Console | 166 USB Port Specifications for the MX10008 Router The following Juniper Networks USB flash drives have been tested and are officially supported for the USB port in the MX10008 router: RE-USB-1G-S—1-gigabyte (GB) USB flash drive RE-USB-2G-S—2-GB USB flash drive...
Page 126: Management Port Connector Pinouts For The Mx10008 Router
Management Port Connector Pinouts for the MX10008 Router The 1000BASE-T RJ-45 management ports use an RJ-45 connector to connect either to the control plane and management network in an MX10008 router, or to a management device for out-of-band management. Table 49 on page 127 provides the pinout information of the RJ-45 management port connector.
Page 127 Table 49: RJ-45 Management Port Connector Pinouts for the MX10008 Router (continued) Signal Description TRP4+ Transmit/receive data pair 4 TRP4– Transmit/receive data pair 4 SEE ALSO MX10008 Routing and Control Board LEDs | 80...
Page 128: Initial Installation And Configuration
Unpacking the MX10008 Router and Components | 132 Installing the Mounting Hardware | 140 Installing the MX10008 into a Rack | 143 Installing the Front Panel on an MX10008 | 151 Connecting the MX10000 to Power | 158 Connecting the MX10008 to External Devices | 164...
Page 130: Mx10008 Installation Overview
The router chassis is bolted to the pallet base. You can install an MX10008 router in a standard 19 in. (483 mm) equipment rack by using the supplied rack mount kit and the flange that is attached to the chassis.
Page 131: Unpacking The Mx10008 Router And Components
The chassis is maximally protected inside the shipping box. Do not unpack it until you are ready to begin the installation. Ensure that you have the following parts and tools available to unpack the MX10008: A 13/32 in. (10 mm) open-end wrench or socket wrench to remove the bracket bolts from the shipping...
Page 132 To unpack the chassis (see Figure 48 on page 133): Figure 48: Shipping Crate and Accessory Box 1. Move the shipping box to a staging area as close to the installation site as possible. While the chassis is bolted to the pallet, you can use a forklift or pallet jack to move it. Make sure there is enough space to remove components from the chassis.
Page 133 31 for information about base configurations and redundant configurations and “Comparing the MX10008 Order to the Pack” on page 136. 11. Store the brackets and bolts inside the accessory box. 12. Save the shipping box and packing materials in case you need to move or ship the router at a later time.
Page 134: Unpacking Line Cards, Rcbs, And Switch Fabric Boards
“Prevention of Electrostatic Discharge Damage” on page 343. Ensure that you know how to handle and store the component. (See “Handling and Storing MX10008 Line Cards, RCBs, and SFBs” on page 244). To unpack an RCB, SFB, or line card, (see...
Page 135: Comparing The Mx10008 Order To The Pack
The packing list specifies the part number and description of each part in your order. If any part on the packing list is missing, contact your customer service representative, or contact Juniper Networks Customer Care from within the U.S. or Canada by telephone at 1-888-314-5822. For international-dial or direct-dial options in countries without toll-free numbers, see https://www.juniper.net/support/requesting-support.html.
Page 136 Table 50: Premium Redundant Configuration Order Component MX10008 Quantity Chassis, including power bus Routing and Control Boards Fan tray controllers Fan trays Power supplies JNP10K-PWR-AC JNP10K-PWR-AC2, only available on chassis with the enhanced power bus JNP10K-PWR-DC JNP10K-PWR-DC2, only available on chassis with the enhanced power bus...
Page 137 Front panel kit, lockable (see Table 54 on page 139) Documentation Roadmap Card 3. Compare the contents of the accessory kit with Table 52 on page 138. Table 52: MX10008 Accessory Kit Quantity Component AC Configurations DC Configurations Warranty card End-user license agreement (EULA)
Page 138 Table 52: MX10008 Accessory Kit (continued) Quantity Component AC Configurations DC Configurations Chassis ground lug, 2-hole, 10-32, 6 AWG Power cord retainer clips Premium Base – MX10008 DC terminal lugs, 2-hole, 10-32, – Premium Base 4 AWG MX10008 ESD bags 4.
Page 139: Installing The Mounting Hardware
MX10008 Components and Configurations | 31 Installing the Mounting Hardware An MX10008 can be installed in a four-post rack or in an open-frame rack. Install the mounting hardware on the rack before installing the router. To mount the chassis on a four-post rack, you must first install the mounting hardware in the rack. The MX10008 and MX10016 routers come with a four-piece set of brackets that supports the chassis in the rack.
Page 140 2. Decide where to place the chassis in the rack. If the rack is empty, mount the router in the lowest possible location. See “MX10008 Rack Requirements” on page 96 for the router being installed. 3. Position the left base bracket at the desired position in the left side of the rack and line up its front screw holes with the holes in the rack.
Page 141 Figure 51: Mounting Brackets for Four-Post Rack Installation Right and left base brackets Rear brackets — — 6. Position the right base bracket at the desired position in the right side of the rack opposite the installed left base bracket, so that it is on the same rack level as the left base bracket. If the right and left base brackets are not on the same level, the chassis will rest at an angle in the rack instead of resting flat and level.
Page 142: Installing The Mx10008 Into A Rack
Installing the MX10008 into a Rack IN THIS SECTION Mounting an MX10008 in a 4-Post Rack Using a Mechanical Lift | 143 Manually Mounting an MX10008 in a 4-Post Rack | 147 Mounting an MX10008 in a 4-Post Rack Using a Mechanical Lift Because of the router's size and weight, we strongly recommend using a mechanical lift to install the MX10008.
Page 143 For details, see “MX10008 Clearance Requirements for Airflow and Hardware Maintenance” on page 2. Load the router onto the lift, making sure it rests securely on the lift platform.
Page 144 Figure 52: Loading the MX10008 into a Rack Using a Mechanical Lift 3. Using the lift, align the router in front of the rack, centering it in front of the base brackets. 4. Lift the chassis approximately 0.75 in. (1.9 cm) above the surface of the base brackets. Align the chassis as close as possible to the base brackets.
Page 145 10. After you install the mounting screws and securely bolt the chassis to the rack, reinstall the components in the chassis. SEE ALSO Manually Mounting an MX10008 in a 4-Post Rack | 147 MX10008 Site Preparation Checklist | 91 MX10008 Clearance Requirements for Airflow and Hardware Maintenance | 98...
Page 146: Manually Mounting An Mx10008 In A 4-Post Rack
“MX10008 Site Preparation Checklist” on page 2. Ensure the site has adequate clearance for both airflow and hardware maintenance as described in “MX10008 Clearance Requirements for Airflow and Hardware Maintenance” on page 3. Unpack the router as described in “Unpacking the MX10008” on page 132.
Page 147 Ensure that you have the following parts and tools available to install the router: 14 mounting screws appropriate for your rack A Phillips (+) screwdriver, number 2 or number 3, depending on the size of your rack-mounting screws To install the router in the rack or cabinet (see Figure 55 on page 150): CAUTION:...
Page 148 Figure 54: Lifting the MX10008 Without Using a Mechanical Lift 4. Carefully slide the router onto the base and rear mounting brackets until the chassis flanges contact the rack rails. The mounting brackets ensure that the holes in the flanges align with the holes in the rack rails.
Page 149 How to Install a JNP10K-PWR-DC Power Supply on page 220 SEE ALSO Mounting an MX10008 in a 4-Post Rack Using a Mechanical Lift | 143 Connecting an MX10000 to Earth Ground | 160 Connecting AC Power to an MX10000 | 163...
Page 150: Installing The Front Panel On An Mx10008
Installing the Front Panel on an MX10008 The front panel is required on the MX10008 router to protect fiber optic cabling and to provide additional protection from electromagnetic interference (EMI). The front panel can be installed with or without the optional cable management system.
Page 151 4. Use the Phillips screwdriver to attach two mounting screws to the right base bracket at the bottom right side of the chassis frame. 5. Use the Phillips screwdriver to attach two mounting screws to the latch bracket at the top left of the chassis frame (see Figure 57 on page 153 for MX10008 installation).
Page 152 Figure 57: Attaching Front Panel Brackets on an MX10008 6. Use the final two mounting screws to attach a latch bracket to the top right of the chassis frame so there are brackets on all four corners of the front of the chassis.
Page 153 Figure 58: Front Panel Installation on an MX10008 The front panel has an air filter to keep the dust away from the chassis. To remove the air filter in the front panel: 1. Attach an ESD grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 154 Figure 59: Air Filter Frame in an MX10008 CAUTION: Always keep the air filter in place while the device is operating. Because the fans are very powerful, they could pull small bits of wire or other materials into the through the unfiltered air intake. This could damage the components.
Page 155 Figure 60: Air Filter in an MX10008 Front Panel To install the air filter in the front panel: 1. Attach an ESD grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 156 Figure 61: Air Filter Frame in an MX10008 Front Panel 3. Hold the air filter with both hands and insert it into the front panel until it stops.
Page 157: Connecting The Mx10000 To Power
Figure 62: Inserting the AIr Filter into an MX10008 Front Panel 4. Move the air filter frame over the front panel and turn the knob on the air filter frame clockwise back in place. NOTE: You must replace the filter every 6 months.
Page 158 MX10008 and MX10016 routers support both AC and DC power supplies. Additionally, MX10000 routers also support high-voltage alternating current (HVAC) and high-voltage direct current (HVDC) power supplies. To connect power to a MX10008 router or a MX10016 router, refer to the following procedures: NOTE: Do not mix power supply models in the same chassis in a running environment.
Page 159: Connecting An Mx10000 To Earth Ground
(see Figure 65 on page 162). Before you connect earth ground to the protective earthing terminal of an MX10008, or MX10016, ensure that a licensed electrician has attached an appropriate grounding lug to the grounding cable. CAUTION: Using a grounding cable with an incorrectly attached lug can damage the router.
Page 160 3. Attach an ESD grounding strap to your bare wrist, and connect the strap to the ESD grounding point next to the earthing posts (see Figure 63 on page 161 Figure 64 on page 161). Figure 63: ESD Point for the MX10008 Grounding point — Figure 64: ESD Point for the MX10016 Grounding point —...
Page 161 Figure 65 on page 162 Figure 66 on page 162. Figure 65: Connecting a Grounding Cable to the MX10008 Figure 66: Connecting a Grounding Cable to the MX10016 6. Place the two screws over the grounding lug and grounding cable.
Page 162: Connecting Ac Power To An Mx10000
SEE ALSO General Safety Guidelines and Warnings | 313 Grounded Equipment Warning | 328 Removing and Installing MX10000 Power System Components | 191 Connecting AC Power to an MX10000 After you ground the chassis, connect the power supplies, and supply power to the chassis, the system initiates the power-on sequence.
Page 163: Connecting Dc Power To An Mx10000
General Safety Guidelines and Warnings | 313 Grounded Equipment Warning | 328 Connecting the MX10008 to External Devices IN THIS SECTION Connecting an MX10008 to a Network for Out-of-Band Management | 165 Connecting an MX10008 Router to a Management Console | 166...
Page 164: Connecting An Mx10008 To A Network For Out-Of-Band Management
Connecting an MX10008 to a Network for Out-of-Band Management You can monitor and manage an MX10008 router using a dedicated management channel. Each MX10008 Routing and Control Board (RCB) has two management ports: a 10/100/1000BASE-T RJ-45 port for copper connections and a 1-Gigabit SFP port for fiber connections. Use the management ports to connect the RCB to a network for out-of-band management.
Page 165: Connecting An Mx10008 Router To A Management Console
Connecting an MX10008 Router to a Management Console | 166 Connecting an MX10008 Router to a Management Console The MX10008 router has a console port with an RJ-45 connector. Use the console port to connect the device to a management console or to a console server.
Page 166: Configuring An Mx10008 Router
Console Port Connector Pinouts for an MX10008 Router | 125 Configuring an MX10008 Router You must perform the initial configuration of an MX10008 router through the console port using the command-line interface (CLI). Before you begin connecting and configuring the router, set the following parameter values on the console server or PC: Baud Rate—9600...
Page 167 The management ports, em0 (MGMT for RJ-45 connections) and em1 (also labeled MGMT for fiber connections), are found on the port panel of the RCBs of the MX10008 router. 9. (Optional) Configure the static routes to remote prefixes with access to the management port.
Page 168 NOTE: When Telnet is enabled, you cannot log in to an MX10008 through Telnet using root credentials. Root login is allowed only for SSH access. 11. Commit the configuration to activate it on the router. [edit] root@# commit RELATED DOCUMENTATION...
Page 169: Maintaining Components
Field-Replaceable Units in an MX10008 | 173 Removing and Installing Routing and Control Boards | 174 Removing and Installing MX10008 Cooling System Components | 178 Removing and Installing MX10000 Power System Components | 191 Removing and Installing MX10008 Switch Fabric Boards | 244...
Page 171: Field-Replaceable Units In An Mx10008
Hot-pluggable—You can remove and replace these components without powering off the router, but the routing function is interrupted until you replace the component. Table 7 on page 38 lists the FRUs and their types for the MX10008 routers. Table 55: FRUs in an MX10008 Router Type Power supplies Hot-insertable and hot-removable.
Page 172: Removing And Installing Routing And Control Boards
OS release in which the transceivers were introduced. NOTE: If you have a Juniper Care service contract, register any addition, change, or upgrade of hardware components at https://www.juniper.net/customers/support/tools/updateinstallbase/. Failure to do so can result in significant delays if you need replacement parts. This note does not apply if you replace an existing component with the same type of component.
Page 173: Removing A Routing And Control Board
Removing a Routing and Control Board An MX10008 can have one or two Routing and Control Boards (RCBs), depending on the configuration. RCBs can be installed in either of the two top slots on the front of the chassis. In redundant configurations, an RCB is a hot-removable and hot-insertable field-replaceable unit (FRU).
Page 174: Installing A Routing And Control Board
Handling and Storing MX10008 Line Cards, RCBs, and SFBs | 244 Installing a Routing and Control Board An MX10008 can have one or two Routing and Control Boards (RCBs), depending on the configuration. RCBs can be installed in either of the two top slots on the front of the chassis.
Page 175 1. Wrap and fasten one end of an ESD strap around your bare wrist, and connect the other end of the strap to the ESD point on the front of an MX10008 (see Figure 72 on page 177). Figure 72: ESD Point for MX10008 Chassis Front...
Page 176: Removing And Installing Mx10008 Cooling System Components
You can also use the the show chassis environment cb command to verify that the RCB is online. SEE ALSO Power Requirements for MX10008 Components MX10008 Routing and Control Board LEDs | 80 Handling and Storing MX10008 Line Cards, RCBs, and SFBs | 244 Removing and Installing MX10008 Cooling System Components IN THIS SECTION...
Page 177: Removing An Mx10008 Fan Tray
Removing an MX10008 Fan Tray Controller | 186 Installing an MX10008 Fan Tray Controller | 188 An MX10008 router has two independent, field-replaceable fan trays. Fan trays must be replaced within the duration mentioned in Table 56 on page 179.
Page 178 ESD point on the rear left side of the chassis. See Figure 75 on page 180. Figure 75: ESD Point on the Rear of an MX10008 ESD point — 2. Loosen the four captive screws either by unscrewing with your thumb and forefinger or by using a Phillips screwdriver.
Page 179 Figure 76: Removing Fan Tray JNP10008-FAN from an MX10008 FAN FTC SIB STATUS FAN FTC SIB STATUS...
Page 180 Figure 77: Removing Fan Tray JNP10008-FAN2 from an MX10008 4. Tilt the top of the fan tray forward. CAUTION: See the heat symbol on the fan tray. The fan handle and its surfaces including the power supply handles may be hot. Wear proper protective, heat-resistant gloves while removing the fan tray.
Page 181: Installing An Mx10008 Fan Tray
Field-Replaceable Units in an MX10008 | 38 Installing an MX10008 Fan Tray An MX10008 chassis has two independent, field-replaceable fan trays. Each fan tray is a hot-removable and hot-insertable field-replaceable unit (FRU); you can remove and replace the fan tray while the router is running without turning off power to the router or disrupting routing functions.
Page 182 (see Figure 78 on page 184). Figure 78: ESD Point on the Rear of an MX10008 ESD point — 2. Grasp the top and bottom fan tray handles and align the bottom of the fan tray with the bottom of the fan tray slot.
Page 183 Figure 79: Installing Fan Tray JNP10008-FAN in an MX10008 FAN FTC SIB STATUS FAN FTC SIB STATUS...
Page 184: Removing An Mx10008 Fan Tray Controller
Figure 80: Installing Fan Tray JNP10008-FAN2 in an MX10008 SEE ALSO Removing an MX10008 Fan Tray | 179 MX10008 Cooling System and Airflow | 45 Field-Replaceable Units in an MX10008 | 38 Removing an MX10008 Fan Tray Controller For each of the two fan trays, there is a fan tray controller. Each controller is a hot-removable and hot-insertable field-replaceable unit (FRU);...
Page 185 Figure 81 on page 187 for JNP10008-FAN-CTRL and Figure 82 on page 187. Figure 81: JNP10008-FAN-CTRL Figure 82: JNP10008-FTC2 CAUTION: Do not remove the fan tray controller unless you have a replacement controller available. To access a fan tray controller, you must first remove the fan tray. With the fan tray removed, the fan tray controller is installed horizontally above the Switch Fabric Boards (SFBs) at the top of the chassis.
Page 186: Installing An Mx10008 Fan Tray Controller
Installing an MX10008 Fan Tray Controller Each fan tray of an MX10008, has a fan tray controller. Each controller is a hot-removable and hot-insertable field-replaceable unit (FRU); you can remove and replace one fan tray controller while the router is running without turning off power to the router or disrupting routing functions.
Page 187 You have removed the associated fan tray and fan tray controller. See “Removing an MX10008 Fan Tray” on page 179 “Removing an MX10008 Fan Tray Controller” on page 186. Ensure that you have the following parts and tools available to install a fan tray controller:...
Page 188 See Figure 86 on page 190. Figure 86: Replacing an MX10008 Fan Tray Controller 3. Using a Phillips screwdriver, tighten the captive screws for the fan tray controller. 4. Replace the fan tray. See “Installing an MX10008 Fan Tray” on page 183.
Page 189: Removing And Installing Mx10000 Power System Components
MX10008 and MX10016 routers support both AC and DC power supplies. Additionally, MX10000 routers support high-voltage alternating current (HVAC) or high-voltage direct current (HVDC) power supplies. To install and remove the power supplies in a MX10008 router or a MX10016 router, refer to the following sections.
Page 190 Do not leave the power supply slot empty for a long time while the router is operational. Either replace the power supply promptly or install a cover panel over the empty slot. To remove a JNP10K-PWR-AC power supply from an MX10008 router::...
Page 191 1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. There is an ESD point located next to the protective earthing terminal and below PSU 5 on the MX10008 rear panel (see Figure 87 on page...
Page 192 4. Remove the power cords from the AC inlet on the AC power supply faceplate. 5. Turn the adjustment nut of the power cord retainers counterclockwise until you can see the power cord. Pull the power cord from the slot in the adjustment nuts. 6.
Page 193 Figure 89: Removing a JNP10K-PWR-AC Power Supply from an MX10008 Figure 90: Removing a JNP10K-PWR-AC Power Supply from an MX10016 Keep latch in open position during removal.
Page 194: How To Install A Jnp10K-Pwr-Ac Power Supply
JNP10K-PWR-AC Power Supply | 61 How to Install a JNP10K-PWR-AC Power Supply The JNP10K-PWR-AC power supply in an MX10008 chassis or a MX10016 chassis is a hot-insertable and hot-removable field-replaceanble unit (FRU). You can install up to 6 power supplies in an MX10008 and 10 in a MX10016 router chassis.
Page 195 Electrostatic discharge (ESD) grounding strap Phillips (+) screwdriver, number 1 Power cords appropriate for your geographical location. See “MX10000 Power Cables Specifications” on page 107. Power cord retainer clips To install a JNP10K-PWR-AC power supply in an MX10008 or an MX10016:...
Page 196 1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. There is an ESD point located next to the protective earthing terminal and below PSU 5 on the MX10008 rear panel (see Figure 91 on page...
Page 197 Figure 93: Removing the PSU Cover Panel on an MX10008 Figure 94: Removing the PSU Cover Panel on a MX10016 3. Taking care not to touch power supply connections, remove the power supply from its bag. 4. Peel back and remove the protective plastic wrap that covers all four sides of the power supply.
Page 198 7. Rotate the captive screw away from the faceplate of the power supply to release the latch. You can install the power supplies in any slot labeled PSU 0 through PSU 5 (top to bottom) on an MX10008 and PSU 0 through PSU 9 on a MX10016.
Page 199 To load balance, route the power cables to alternate between power sources. The JNP10K-PWR-AC does not share power; all power comes into INP1 (lower receptacle) and only uses INP2 (top receptacle) at fail over. See Figure 97 on page 202 for MX10008 and Figure 98 on page 202...
Page 200 Figure 97: Proper Load Balancing for JNP10K-PWR-AC Power Cables on MX10008 Figure 98: Proper Load Balancing for JNP10K-PWR-AC Power Cables on MX10016 WARNING: Ensure that the power cords do not block access to router components or drape where people can trip on them.
Page 201 13. Squeeze the two sides of the power cord retainer clip and insert the ends of the clip into the holes in the bracket on each side of the AC appliance inlets on the AC power supply faceplate. See Figure 99 on page 203.
Page 202: How To Remove A Jnp10K-Pwr-Ac2 Power Supply
JNP10K-PWR-AC Power Supply | 61 How to Remove a JNP10K-PWR-AC2 Power Supply The JNP10K-PWR-AC2 power supply in an MX10008 or an MX10016 chassis is a hot-removable and hot-insertable field-replaceable unit (FRU). You remove all power supplies from the rear of the chassis.
Page 203 Phillips (+) screwdriver, number 1 Replacement power supply or a cover panel for the power supply slot CAUTION: Do not leave the power supply slot empty for a long time while the router is operational. Either replace the power supply promptly or install a cover panel over the empty slot.
Page 204 Figure 100 on page 206) and below PSU_9 on the MX10016 (see Figure 101 on page 206). Figure 100: ESD Point on the MX10008 Chassis Rear ESD point — Figure 101: ESD Point on the MX10016 Chassis Rear ESD point —...
Page 205 Figure 103 on page 207. Figure 102: Removing a JNP10K-PWR-AC2 from an MX10008 Chassis Figure 103: Removing a JNP10K-PWR-AC2 from an MX10016 Chassis 6. Rotate the captive screw away from the faceplate of the power supply to release the latch.
Page 206: How To Install A Jnp10K-Pwr-Ac2 Power Supply
The JNP10K-PWR-AC2 power supply in an MX10008 or an MX10016 chassis is a hot-insertable and hot-removable field-replaceable unit (FRU). You can install up to 6 AC power supplies in a MX10008 and 10 in a MX10016 router chassis. All power supplies install in the rear of the chassis in the slots provided along the left side.
Page 207 If the AC or DC power source outlets have a powerswitch, set them to the off (O) position. Ensure that you have the following parts and tools available to install an JNP10K-PWR-AC2 power supply: Electrostatic discharge (ESD) grounding strap Phillips (+) screwdriver, number 1 Power cables appropriate for your geographical location (for low-voltage installations) or input amperage (for high-voltage installations).
Page 208 To install a JNP10K-PWR-AC2 power supply in an MX10008 or an MX10016: 1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. There is an ESD point located next to the protective earthing terminal...
Page 209 Figure 106: Removing the Power Supply Cover Panel on an MX10008 Figure 107: Removing the Power Supply Cover Panel on an MX10016 3. Taking care not to touch power supply connections, remove the power supply from its bag. 4. Peel back and remove the protective plastic wrap that covers all four sides of the power supply.
Page 210 You can install the power supplies in any slot labeled PSU 0 through PSU 5 (top to bottom) on an MX10008, and PSU 0 through PSU 9 on a MX10016. 8. Using both hands, place the power supply in the power supply slot on the rear of the system. Slide the power supply straight into the chassis until the power supply is fully seated in the slot.
Page 211 See Figure 110 on page 213 for some possible cabling combinations for MX10008 and Figure 111 on page 214 for MX10016. Figure 110: Proper Load Balancing for JNP10K-PWR-AC2 Power Cables on MX10008...
Page 212 Figure 111: Proper Load Balancing for JNP10K-PWR-AC2 Power Cables on MX100016 12. For each power cable, insert the end of the cable with the Anderson connector into the JNP10K-PWR-AC2 power supply module. The connector snaps and locks the cable into position. WARNING: Ensure that the power cords do not block access to router components or drape where people can trip on them.
Page 213: How To Remove A Jnp10K-Pwr-Dc Power Supply
16. Press the power switch to the on (|) position. How to Remove a JNP10K-PWR-DC Power Supply The JNP10K-PWR-DC power supply in an MX10008 and in an MX10016 chassis is a hot-removable and hot-insertable field-replaceable unit (FRU). You remove DC power supplies from the rear of the chassis.
Page 214 Ensure you understand how to prevent ESD damage. See “Prevention of Electrostatic Discharge Damage” on page 343. Ensure that you have the following parts and tools available to remove a JNP10K-PWR-DC power supply: Electrostatic discharge (ESD) grounding strap Phillips (+) screwdriver, numbers 1 and 2 13/32 in.
Page 215 1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. There is an ESD point located next to the protective earthing terminal and below PSU 5 on the MX10008 rear panel (see Figure 112 on page...
Page 216 5. Rotate the captive screw away from the faceplate of the power supply to release the latch. See Figure 114 on page 218 Figure 115 on page 218. Figure 114: Removing a JNP10K-PWR-DC Power Supply from an MX10008 Figure 115: Removing a JNP10K-PWR-DC Supply from an MX10016 Keep latch in open position during removal.
Page 217 NOTE: Ensure that the ejector is fully open to avoid scratching the chassis. Scratches Ejector fully open Ejector closed 6. Taking care not to touch power supply components, pins, leads, or solder connections, place one hand under the power supply to support it. Grasp the power supply handle with your other hand and pull the power supply completely out of the chassis.
Page 218: How To Install A Jnp10K-Pwr-Dc Power Supply
(FRU). You can install up to 6 JNP10K-PWR-DC power supplies in an MX10008 router chassis and 10 in an MX10016 router chassis. All power supplies install in the rear of the chassis in the slots along the left side of the chassis.
Page 219 NOTE: Each battery return of the DC power supply must be connected as an isolated DC return (DC-I). Ensure you understand how to prevent ESD damage. See “Prevention of Electrostatic Discharge Damage” on page 343. Ensure that you have the following parts and tools available to install a JNP10K-PWR-DC power supply: Electrostatic discharge (ESD) grounding strap DC power source cables (not provided) with the cable lugs (provided) attached The provided terminal lugs in an MX10000 are sized for either4 AWG (21.1 mm...
Page 220 1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. There is an ESD point located next to the protective earthing terminal and below PSU 5 on the MX10008 rear panel (see Figure 116 on page...
Page 221 5. Remove the plastic cable cover from the DC power input terminals by using the Phillips (+) screwdriver, number 2, to loosen the screws (see Figure 118 on page 223). Figure 118: Removing the Plastic Cable Cover on an MX10008 DC Power Supply...
Page 222 6. Remove the nuts from each DC power input terminal, using the 13/32 in. (10 mm) nut driver or socket wrench to loosen the nuts. 7. Ensure that the power source circuit breaker is open so that the voltage across the DC power source cable leads is 0 V and that the cable leads do not become active while you are connecting DC power.
Page 223 12. If the power supply slot on the chassis has a cover panel on it, insert your thumb and forefinger into the finger holes, squeeze, and pull the cover out of the slot. Save the cover panel for later use (see Figure 120 on page 226 for MX10008 installations and Figure 121 on page 226 for MX10016 installations).
Page 224 14. Pull the captive screw away from the faceplate of the power supply to release the latch. You can install the power supplies in any slot labeled PSU 0 through PSU 5 (top to bottom) on an MX10008 and PSU 0 through PSU 9 on an MX10016.
Page 225 18. Tighten the captive screw by turning it clockwise by using the Phillips (+) screwdriver, number 1. When the screw is completely tight, the latch locks into the router chassis. Figure 122: Installing a JNP10K-PWR-DC Power Supply in an MX10008 Figure 123: Installing a JNP10K-PWR-DC Power Supply in an MX10016 Close latch after power supply is fully installed.
Page 226 19. Route INP1 cables to a power source and INP2 to another power source. The JNP10K-PWR-DC shares power, so if power dips on one input, the power supply is able to load balance internally. See Figure 124 on page 228 Figure 125 on page 229. Figure 124: Proper Load Balancing for JNP10K-PWR-DC Power Cables on MX10008...
Page 227 Figure 125: Proper Load Balancing for JNP10K-PWR-DC Power Cables on MX100016 WARNING: Ensure that the power cords do not block access to router components or drape where people can trip on them. 20. Set the enable switches for input 1 and input 2 (see Figure 126 on page 230).
Page 228: How To Remove A Jnp10K-Pwr-Dc2 Power Supply
SEE ALSO How to Remove a JNP10K-PWR-DC Power Supply | 215 Connecting DC Power to an MX10000 | 164 Power Requirements for an MX10008 Router | 100 Field-Replaceable Units in an MX10008 | 38 JNP10K-PWR-AC Power Supply | 61 How to Remove a JNP10K-PWR-DC2 Power Supply The JNP10K-PWR-DC2 power supply in an MX10000 chassis is a hot-removable and hot-insertable field-replaceable unit (FRU).
Page 229 “Power Requirements for an MX10008 Router” on page 100, Calculating Power Requirements for an MX10016, and “Calculating the Power Consumption of Your MX10008 Configuration” on page 101. Before you remove a DC power supply from the router: Ensure you understand how to prevent ESD damage. See “Prevention of Electrostatic Discharge Damage”...
Page 230 1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. There is an ESD point located next to the protective earthing terminal and below PSU 5 on the MX10008 rear panel (see Figure 127 on page 232...
Page 231 Figure 130 on page 233.) Figure 129: Removing a JNP10K-PWR-DC2 Power Supply on an MX10008 Figure 130: Removing a JNP10K-PWR-DC2 Power Supply on an MX10016 6. Put on the heat resistant gloves to protect your hands from the hot power supply.
Page 232: How To Install A Jnp10K-Pwr-Dc2 Power Supply
The JNP10K-PWR-DC2 power supply in an MX10000 chassis is a hot-removable and hot-insertable field-replaceable unit (FRU). You can install up to 6 power supplies in an MX10008 router chassis. All HVDC power supplies install in the rear of the chassis in the slots along the left side of the chassis.
Page 233 CAUTION: To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation, you must connect MX10008 routers to earth ground before you connect them to power. For installations that require a separate grounding conductor to the chassis, use the protective earthing terminal on the router chassis to connect to earth ground.
Page 234 1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. There is an ESD point located next to the protective earthing terminal and below PSU 5 on the MX10008 rear panel (see Figure 131 on page...
Page 235 5. Remove the plastic cable cover from the power input terminals by using the Phillips (+) screwdriver, number 2, to loosen the screws (see Figure 133 on page 237). Figure 133: Removing the Plastic Cable Cover on a JNP10K-PWR-DC2 Power Supply 6.
Page 236 CAUTION: You must ensure that power connections maintain the proper polarity. The power source cables might be labeled (+) and (–) to indicate their polarity. There is no standard color coding for DC power cables. 9. Install each power cable lug on the DC power input terminal, securing it with the nut (see Figure 134 on page 238).
Page 237 Figure 136 on page 239). Figure 135: Removing the Power Supply Cover Panel on an MX10008 Figure 136: Removing the Power Supply Cover Panel on an MX10016 12. Unscrew the captive screw in the counterclockwise direction by using the Phillips (+) screwdriver, number 1.
Page 238 16. Tighten the captive screw by turning it clockwise by using the Phillips (+) screwdriver, number 1. When the screw is completely tight, the latch locks into the router chassis. Figure 137: Installing a JNP10K-PWR-DC2 in an MX10008...
Page 239 17. Route INP1 cables to a power source and INP2 to another power source. The JNP10K-PWR-DC shares power, so if power dips on one input, the power supply is able to load balance internally. See Figure 139 on page 241 Figure 140 on page 242. Figure 139: Proper Load Balancing for JNP10k-PWR-DC2 Power Cables on MX10008...
Page 240 Figure 140: Proper Load Balancing for JNP10K-PWR-DC2 Power Cables on MX100016 WARNING: Ensure that the power cords do not block access to router components or drape where people can trip on them. 18. Set the three dip switches to set the inputs and whether the power supply is running at 3000 W, 5000 W, or 5500 W.
Page 241 Table 58: Setting the JNP10K-PWR-DC2 Dip Switches (continued) Switch State Field Enabled for 30 A feed; 5500-W for a single feed, 5000-W for dual feeds Enabled for 20 A feed; power supply capacity is 3000-W Figure 141: Setting the Enable Routers for the Power Source Dip switches Power switch, on (|) and standby (O) —...
Page 242: Removing And Installing Mx10008 Switch Fabric Boards
Holding Switch Fabric Boards | 246 Storing Line Cards, RCBs, and SFBs | 247 The MX10008 chassis has several field-replaceable units (FRUs) that have fragile components. To avoid damaging the line cards, routing and control boards (RCBs), and Switch Fabric Boards (SFBs), you must follow safe handling practices.
Page 243 3. Take care not to strike the unit against any object as you carry it. CAUTION: Never hold the line card or RCB by the connector edge. The connectors are fragile and the line card or RCB will not seat properly if the connector is damaged. Figure 142 on page 245.
Page 244: Holding Switch Fabric Boards
Holding Switch Fabric Boards While removing an SFB from the router chassis, you should hold the SFB vertically until it is clear of the router chassis. Then you should rotate the SFB 90 degrees and place it on an antistatic mat or in an electrostatic bag for storage (see Figure 143 on page 246).
Page 245: Storing Line Cards, Rcbs, And Sfbs
2. Orient the unit with the faceplate toward you. 3. Carefully insert the connector edge into the opening of the bag and pull the bag toward you to cover the unit. SEE ALSO Installing an MX10008 Switch Fabric Board | 251...
Page 246: Removing An Mx10008 Switch Fabric Board
Removing an MX10008 Switch Fabric Board An MX10008 router has six Switch Fabric Boards (SFBs) that are located in the middle of the chassis behind the fan trays. SIB 0 through SIB 2 are located behind the left fan tray and SIB 3 through SIB 5 are located behind the right fan tray.
Page 247 Figure 144: ESD Point on MX10008 Chassis Rear ESD point — 6. Loosen the captive screws at the top and bottom of the card. 7. Grasp both handles and spread them apart, and then slide the SFB about a quarter of the way out of the slot.
Page 248 SFB halfway out of the chassis. Wear proper protective, heat-resistant gloves while removing an SFB. Figure 146: Removing the SFB from an MX10008 Chassis 9. Support the SFB as you rotate the SFB 90 degrees and place it on the antistatic mat with the printed circuit board facing upward.
Page 249: Installing An Mx10008 Switch Fabric Board
Installing an MX10008 Switch Fabric Board An MX10008 router has six Switch Fabric Boards (SFBs) that are located in the middle of the chassis behind the fan trays. SFB 0 through SFB 2 are located behind the left fan tray, and SFB 3 through SFB 5 are located behind the right fan tray.
Page 250 2. Wrap and fasten one end of an ESD strap around your bare wrist, and connect the other end of the strap to the ESD point on the chassis. There is an ESD point located next to the protective earthing terminal and below PSU 5 on the MX10008 rear panel (see Figure 148 on page 252).
Page 251 Figure 149: Removing an SFB Cover Plate on an MX10008 4. Lift the SFB by the handle with one hand and support the lower edge with the other hand. 5. Holding the SFB vertically, slide the SFB into the open slot until the ejector handles engage and start to close.
Page 252 7. Tighten the captive screws by using your thumb and forefinger. 8. Install the appropriate fan tray (see “Installing an MX10008 Fan Tray” on page 183). 9. Set the fans to normal speed by using the test chassis fan tray speed 0 normal and test chassis fan tray speed 1 normal command.
Page 253 SFB online. To delete the existing configuration and bring a replacement SFB online, use the delete chassis sib power-off slot slot number command. SEE ALSO Removing an MX10008 Fan Tray | 179...
Page 254: Replacing An Mpc
Ensure that you have taken the necessary precautions to prevent electrostatic discharge (ESD) damage (see “Prevention of Electrostatic Discharge Damage” on page 343). Ensure that you know how to handle and store the line card (see “Handling and Storing MX10008 Line Cards, RCBs, and SFBs” on page 244).
Page 255 When you remove an MPC, the router continues to function, although the interfaces that are installed on the MPC that is being removed no longer function. An MPC is installed horizontally in the front of the router. MPCs are hot-insertable and hot-removable. A fully configured MPC can weigh up to 31.57 lb.
Page 256 CAUTION: Do not leave a fiber-optic transceiver uncovered except when inserting or removing a cable. The safety cap keeps the port clean and prevents accidental exposure to laser light. CAUTION: Avoid bending a fiber-optic cable beyond its minimum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose.
Page 257: Installing An Mpc
CAUTION: After removing an MPC from the chassis, wait at least 30 seconds before replacing it with another MPC, or inserting an MPC into a different slot. Figure 151: Removing an MPC Installing an MPC An MPC is installed horizontally in the front of the router. MPCs are hot-insertable and hot-removable. An MPC can weigh up to 31.57 lb (14.32 kg).
Page 258 4. Orient the MPC so that the faceplate is toward you. 5. Lift the MPC into place, and carefully align the sides of the MPC with the guides inside the card cage. CAUTION: When the MPC is out of the chassis, do not hold it by the ejector handles, bus bars, or edge connectors.
Page 259: Install The Cable Management System
Figure 152: Installing an MPC MX 10 00 8 Install the Cable Management System The cable management system is an optional kit that can be ordered to organize and protect optical cabling attached to the line cards. After a card is installed, you can still remove the line card without needing to remove the cable management system.
Page 260 To install the cable management system (see Figure 153 on page 262): 1. Open the shipping carton of the cable management system and check that you have: Two handle extensions One cable tray Figure 153: Cable Management System Components Handle extensions Cable tray —...
Page 261 Figure 155: Adding Handle Extensions 4. Tighten the screws into the handle extensions. 5. Snap open the blue clips on the ends of the cable tray with your hands. 6. Place the cable tray across the front of the line card so that the two ends of the cable tray are under the handle extensions.
Page 262: Removing And Installing Transceivers And Fiber-Optic Cables
Drape some of the cables under the handle extension and some cables over the handle extension. Figure 157: Completed Cable Management System Removing and Installing Transceivers and Fiber-Optic Cables IN THIS SECTION Remove a Transceiver | 265 Install a Transceiver | 267 Disconnect a Fiber-Optic Cable from a Router | 269 Connect a Fiber-Optic Cable to a Router | 270 Maintain the Fiber-Optic Cables in a Router | 271...
Page 263: Remove A Transceiver
Remove a Transceiver The transceivers for the router are hot-removable and hot-insertable field-replaceable units (FRUs). You can remove and replace the transceivers without powering off the device or disrupting device functions. NOTE: After you remove a transceiver or when you change the media-type configuration, wait for 6 seconds for the interface to display the operational commands.
Page 264 WARNING: Do not leave a fiber-optic transceiver uncovered except when inserting or removing a cable. The rubber safety cap keeps the port clean and prevents accidental exposure to laser light. CAUTION: Do not bend fiber-optic cables beyond their minimum bend radius. Bending the cables beyond their minimum bend radius can damage the cables and cause problems that are difficult to diagnose.
Page 265: Install A Transceiver
Juniper Networks with your Juniper Networks device. CAUTION: If you face a problem running a Juniper Networks device that uses a third-party optic or cable, the Juniper Networks Technical Assistance Center (JTAC) can help you diagnose the source of the problem. Your JTAC engineer might recommend that you check the third-party optic or cable and potentially replace it with an equivalent Juniper Networks optic or cable that is qualified for the device.
Page 266 3. Check whether the transceiver is covered with a rubber safety cap. If it is not, cover the transceiver with a rubber safety cap. WARNING: Do not leave a fiber-optic transceiver uncovered except when inserting or removing a cable. The rubber safety cap keeps the port clean and prevents accidental exposure to laser light.
Page 267: Disconnect A Fiber-Optic Cable From A Router
Figure 159: Installing a Transceiver Ejector lever — Disconnect a Fiber-Optic Cable from a Router The router has field-replaceable optical transceivers to which you can connect fiber-optic cables. Before you disconnect a fiber-optic cable from an optical transceiver installed in the router, ensure that you have taken the necessary precautions for safe handling of lasers (see “Laser and LED Safety Guidelines and Warnings”...
Page 268: Connect A Fiber-Optic Cable To A Router
3. Cover the transceiver with a rubber safety cap. WARNING: Do not leave a fiber-optic transceiver uncovered except when inserting or removing a cable. The rubber safety cap keeps the port clean and prevents accidental exposure to laser light. 4. Cover the fiber-optic cable connector with the rubber safety cap. Connect a Fiber-Optic Cable to a Router The router has field-replaceable unit (FRU) optical transceivers to which you can connect fiber-optic cables.
Page 269: Maintain The Fiber-Optic Cables In A Router
CAUTION: Do not bend fiber-optic cables beyond their minimum bend radius. Bending the cables beyond their minimum bend radius can damage the cables and cause problems that are difficult to diagnose. CAUTION: Do not let fiber-optic cables hang free from the connector. Do not allow fastened loops of cables to dangle, which stresses the cables at the fastening point.
Page 270: Removing The Mx10008 Router
IN THIS SECTION Powering Off an MX10008 Router | 272 Removing an MX10008 Router From a Four-Post Rack Using a Mechanical Lift | 275 Manually Removing an MX10008 Router from a 4-Post Rack | 276 Powering Off an MX10008 Router NOTE: Use the following procedure to power off an MX10008.
Page 271 Connect a management device to one of the two management (MGMT) ports on the RCB by following the instructions in “Connecting an MX10008 to a Network for Out-of-Band Management” on page 165. 2. Shut down Junos OS from the external management device by issuing the request vmhost halt operational mode CLI command.
Page 272 Stopping vehostd: [ Stopping watchdog: [ Stopping xinetd: [ Sending all processes the TERM signal... [ Sending all processes the KILL signal... [ Saving random seed: Syncing hardware clock to system time [ Turning off swap: Unmounting file systems: init: Re-executing /sbin/init Halting system...
Page 273: Removing An Mx10008 Router From A Four-Post Rack Using A Mechanical Lift
Connecting DC Power to an MX10000 | 164 Removing an MX10008 Router From a Four-Post Rack Using a Mechanical Lift Because of the router's size and weight, we strongly recommend using a mechanical lift to install the MX10008. NOTE: For instructions on installing a router without using a mechanical lift, see “Manually Mounting...
Page 274: Manually Removing An Mx10008 Router From A 4-Post Rack
4. Move the lift away from the rack and lower the lift. 5. Use the lift to transport the router to its new location. Figure 160: Moving the MX10008 Using a Mechanical Lift SEE ALSO Powering Off an MX10008 Router | 272 Manually Removing an MX10008 Router from a 4-Post Rack If you cannot use a mechanical lift to remove the router (the preferred method), you can install it manually.
Page 275 Ensure that the rack is stable and secured to the building. Ensure there is enough space to place the removed router in its new location and along the path to the location.“MX10008 Clearance Requirements for Airflow and Hardware Maintenance” on page Review “General Safety Guidelines and Warnings”...
Page 276 Figure 161 on page 278. Figure 161: Lifting the MX10008 Without Using a Mechanical Lift 6. Carefully move the chassis to its new location. After moving the router to its new location, reinstall the components in the chassis or store the...
Page 277 SEE ALSO Removing an MX10008 Router From a Four-Post Rack Using a Mechanical Lift | 275 Connecting an MX10000 to Earth Ground | 160 Connecting AC Power to an MX10000 | 163 Connecting DC Power to an MX10000 | 164...
Page 278: Troubleshooting Hardware
C HAPTER Troubleshooting Hardware Restoring Junos OS | 283 Alarm Messages | 287...
Page 280: Restoring Junos Os
NOTE: You can create the emergency boot device on another Juniper Networks router or router, or any PC or laptop that supports Linux. The steps you take to create the emergency boot device vary, depending on the device.
Page 281 NOTE: The password is the root password for the device. If you logged in to the device as root, you do not need to perform this step. 5. Enter the following command on the device: root@device% dd if=/var/tmp/filename of=/dev/da1 bs=16k The device writes the installation media image to the USB device: root@device% dd if=install-media-qfx-5e-15.1X53-D30.5-domestic.img of=/dev/da0 bs=1m...
Page 282: Performing A Recovery Installation Using An Emergency Boot Device
You can use the system snapshot feature to complete this step. The system snapshot feature takes a “snapshot” of the files currently used to run the MX10008 router—the complete contents of the /config and /var directories, which include the running Juniper Networks Junos OS, the active configuration, and the rescue configuration—and copies all of these files into a memory source.
Page 283 Reboot Install Juniper Linux Platform Boot to host shell [debug] Select Install Juniper Linux Platform to install the Junos OS software from the emergency boot device. The device copies the software from the emergency boot device, occasionally displaying status messages.
Page 284: Alarm Messages
Understanding Alarms | 287 Interface Alarm Messages | 288 Understanding Alarms The MX10008 router supports different alarm types and severity levels. Table 60 on page 287 provides a list of alarm terms and definitions that can help you in monitoring the device.
Page 285: Interface Alarm Messages
By default, major alarms are configured for interface link-down conditions on the control plane and management network interfaces in an MX10008 router. The link-down alarms indicate that connectivity to the control plane network is down. You can configure these alarms to be ignored using the alarm statement at the [edit chassis] hierarchy level.
Page 286: Contacting Customer Support And Returning The Chassis Or Components
C HAPTER Contacting Customer Support and Returning the Chassis or Components Contacting Customer Support | 291 Returning the MX10008 Chassis or Components | 291...
Page 288: Contacting Customer Support
Contacting Customer Support You can contact Juniper Networks Technical Assistance Center (JTAC) 24 hours a day, 7 days a week in one of the following ways: On the Web, using the Service Request Manager link at: https://support.juniper.net/support/ By telephone: From the US and Canada: 1-888-314-JTAC...
Page 289: Returning A Router Or Component For Repair Or Replacement
Returning a Router or Component for Repair or Replacement If you need to return an MX10008 router, or an MX10016 router, or a component to Juniper Networks for repair or replacement, follow this procedure: 1. Determine the serial number of the component. For instructions, see “Locating the Serial Number on...
Page 290: Listing The Chassis And Component Details Using The Cli
Locating the Serial Number ID Labels on an MX10008 Switch Fabric Board (SFB) | 304 If you are returning a router or component to Juniper Networks for repair or replacement, you must locate the serial number of the router or component. You must provide the serial number to the Juniper Networks Technical Assistance Center (JTAC) when you contact them to obtain a Return Materials Authorization (RMA).
Page 291 Xcvr 0 REV 01 740-064669 8543 QSFP28-LPBK Xcvr 1 REV 01 740-064669 8500 QSFP28-LPBK Xcvr 2 REV 01 740-064669 8493 QSFP28-LPBK Xcvr 3 REV 01 740-064669 8506 QSFP28-LPBK PIC 1 BUILTIN BUILTIN 4xQSFP28 SYNCE Xcvr 0 REV 01 740-064669 8490 QSFP28-LPBK Xcvr 1 REV 01...
Page 292 Xcvr 2 REV 01 740-064669 54594 QSFP28-LPBK Xcvr 3 REV 01 740-064669 54645 QSFP28-LPBK PIC 3 BUILTIN BUILTIN 4xQSFP28 SYNCE Xcvr 0 REV 01 740-064669 54607 QSFP28-LPBK Xcvr 1 REV 01 740-064669 54634 QSFP28-LPBK Xcvr 2 REV 01 740-064669 54576 QSFP28-LPBK Xcvr 3 REV 01...
Page 293 PIC 5 BUILTIN BUILTIN 4xQSFP28 SYNCE Xcvr 0 REV 01 740-058734 1ECQ1121090 QSFP-100GBASE-SR4 Xcvr 1 REV 01 740-058734 1ECQ1203091 QSFP-100GBASE-SR4 Xcvr 2 REV 01 740-058734 1ECQ120303F QSFP-100GBASE-SR4 Xcvr 3 REV 01 740-058734 1ECQ120400W QSFP-100GBASE-SR4 FPC 3 REV 04 750-084779 CAKR7020 JNP10K-LC2101 REV 05 750-073391...
Page 294 PIC 1 BUILTIN BUILTIN 4xQSFP28 SYNCE Xcvr 0 REV 01 740-058734 1ECQ120901K QSFP-100GBASE-SR4 Xcvr 1 REV 01 740-058734 1ECQ12030C2 QSFP-100GBASE-SR4 Xcvr 2 REV 01 740-058734 1ECQ120902T QSFP-100GBASE-SR4 Xcvr 3 REV 01 740-058734 1ECQ120305P QSFP-100GBASE-SR4 PIC 2 BUILTIN BUILTIN 4xQSFP28 SYNCE Xcvr 0 REV 01 740-058734...
Page 295 Xcvr 1 REV 01 740-058734 1ECQ1204016 QSFP-100GBASE-SR4 Xcvr 2 REV 01 740-058734 1ECQ12030AA QSFP-100GBASE-SR4 Xcvr 3 REV 01 740-058734 1ECQ120903T QSFP-100GBASE-SR4 PIC 4 BUILTIN BUILTIN 4xQSFP28 SYNCE Xcvr 0 REV 01 740-058734 1ECQ120309B QSFP-100GBASE-SR4 Xcvr 1 REV 01 740-058734 1ECQ11180F1 QSFP-100GBASE-SR4 Xcvr 2 REV 01...
Page 296 Xcvr 3 REV 01 740-058734 1ECQ11210NP QSFP-100GBASE-SR4 FPC 7 REV 04 750-084779 CAKR7009 JNP10K-LC2101 REV 05 750-073391 CAKR1004 LC 2101 PMB PIC 0 BUILTIN BUILTIN 4xQSFP28 SYNCE Xcvr 0 REV 01 740-058734 1ECQ120309E QSFP-100GBASE-SR4 Xcvr 1 REV 01 740-058734 1ECQ1203092 QSFP-100GBASE-SR4 Xcvr 2 REV 01...
Page 297: Locating The Chassis Serial Number Id Label On An Mx10008
Locating the Serial Number ID Labels on MX10008 Power Supplies The power supplies installed in an MX10008 are field-replaceable units (FRUs). For each FRU, you must remove the FRU from the router chassis to see the FRU serial number ID label.
Page 298 JNP10K-PWR-AC power supply—The serial number ID label is on the right side of the power supply. Figure 163 on page 301. Figure 163: JNP10K-PWR-AC Power Supply Serial Number Location JNP10K-PWR-AC2 power supply—The serial ID label is on the right side of the power supply. See Figure 164 on page 301.
Page 299 Figure 165: JNP10K-PWR-DC Power Supply Serial Number Location JNP10K-PWR-DC2 power supply—The serial number ID label is on the left side of the power supply. Figure 166 on page 302. Figure 166: JNP10K-PWR-DC2 Power Supply Serial Number Location Serial number ID label...
Page 300: Locating The Serial Number Id Labels On Mx10008 Fan Trays And Fan Tray Controllers
Locating the Serial Number ID Labels on MX10008 Fan Trays and Fan Tray Controllers The two fan trays and their associated fan tray controllers installed in an MX10008 are field-replaceable units (FRUs). For each FRU, you must remove the FRU from the router chassis to see the FRU serial number ID label.
Page 301: Locating The Serial Number Id Labels On An Mx10008 Line Card
Figure 170: MX10008 Line Card Serial Number Location Serial number ID label Locating the Serial Number ID Labels on an MX10008 Switch Fabric Board (SFB) The serial number ID label for an SFB is located on the PC board. See Figure 171 on page 305.
Page 302: Contacting Customer Support To Obtain A Return Materials Authorization For A Router Or Component
Contacting Customer Support to Obtain a Return Materials Authorization for a Router or Component If you are returning a MX10008 router or component to Juniper Networks for repair or replacement, you must first obtain a Return Materials Authorization (RMA) from the Juniper Networks Technical Assistance Center (JTAC).
Page 303: Packing An Mx10008 Router Or Component For Shipping
Packing an MX10008 Chassis for Shipping | 307 Packing MX10008 Components for Shipping | 309 Follow this procedure if you are returning an MX10008 chassis or component to Juniper Networks for repair or replacement. Before you pack an MX10008 or component: Ensure that you have taken the necessary precautions to prevent electrostatic discharge (ESD) damage.
Page 304: Packing An Mx10008 Chassis For Shipping
Packing an MX10008 Chassis for Shipping The MX10008 is shipped in a cardboard box that has a two-layer wooden pallet base with foam cushioning between the layers. The router chassis is bolted to the pallet base with four pallet fasteners, two on each side of the chassis.
Page 305 6. Position a mechanical lift under the device. If a mechanical lift is not available, have three people support the weight of the router while another person uses the screwdriver to remove the front mounting screws that attach the chassis mounting brackets to the rack. For MX10008 removal, see “Removing an MX10008 Router From a Four-Post Rack Using a Mechanical Lift”...
Page 306: Packing Mx10008 Components For Shipping
See Figure 173 on page 309. Figure 173: Attaching the MX10008 to the Pallet 17. Write the RMA number on the exterior of the box to ensure proper tracking. Packing MX10008 Components for Shipping Before you begin packing a router component, ensure that you have the following parts and tools available:...
Page 307 To pack and ship MX10008 components: 1. Place individual FRUs in antistatic bags. 2. Use the original packing materials if they are available. If the original packing materials are not available, ensure the component is adequately packed to prevent damage during transit. The packing material you use must be able to support the weight of the component.
Page 308: Safety And Compliance Information
Qualified Personnel Warning | 316 Warning Statement for Norway and Sweden | 317 Fire Safety Requirements | 317 Installation Instructions Warning | 319 MX10008 Chassis Lifting Guidelines | 319 Restricted Access Warning | 321 Ramp Warning | 323 Rack-Mounting and Cabinet-Mounting Warnings | 323...
Page 309 Prevention of Electrostatic Discharge Damage | 343 AC Power Electrical Safety Guidelines | 345 AC Power Disconnection Warning | 346 DC Power Electrical Safety Guidelines for MX10008 Router | 346 DC Power Disconnection Warning | 348 DC Power Grounding Requirements and Warning | 350...
Page 310: General Safety Guidelines And Warnings
General Safety Guidelines and Warnings The following guidelines help ensure your safety and protect the device from damage. The list of guidelines might not address all potentially hazardous situations in your working environment, so be alert and exercise good judgment at all times. Perform only the procedures explicitly described in the hardware documentation for this device.
Page 311: Definitions Of Safety Warning Levels
Always ensure that all modules, power supplies, and cover panels are fully inserted and that the installation screws are fully tightened. Definitions of Safety Warning Levels The documentation uses the following levels of safety warnings (there are two Warning formats): NOTE: You might find this information helpful in a particular situation, or you might overlook this important information if it was not highlighted in a Note.
Page 312 WARNING: This symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken.
Page 313: Qualified Personnel Warning
Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. Qualified Personnel Warning WARNING: Only trained and qualified personnel should install or replace the device.
Page 314: Warning Statement For Norway And Sweden
In addition, you should establish procedures to protect your equipment in the event of a fire emergency. Juniper Networks products should be installed in an environment suitable for electronic equipment. We recommend that fire suppression equipment be available in the event of a fire in the vicinity of the equipment and that all local fire, safety, and electrical codes and ordinances be observed when you install and operate your equipment.
Page 315 To keep warranties effective, do not use a dry chemical fire extinguisher to control a fire at or near a Juniper Networks device. If a dry chemical fire extinguisher is used, the unit is no longer eligible for coverage under a service agreement.
Page 316: Installation Instructions Warning
The weight of a fully loaded base AC configuration is approximately 285 lb (129.27 kg) and 332 lb (150.59 kg) for the redundant AC configuration. Similarly, the weight of a redundant DC configuration is 319 lb (144.69 kg). Observe the following guidelines for lifting and moving an MX10008:...
Page 317 Before lifting or moving the MX10008, disconnect all external cables. When raising the MX10008 into the rack, have two people lift and align the router with the rack while another person secures the router to the rack. As when lifting any heavy object, lift most of the weight with your legs rather than your back.
Page 318: Restricted Access Warning
Restricted Access Warning...
Page 319 WARNING: This unit is intended for installation in restricted access areas. A restricted access area is an area to which access can be gained only by service personnel through the use of a special tool, lock and key, or other means of security, and which is controlled by the authority responsible for the location.
Page 320: Ramp Warning
de servicio mediante la utilización de una herramienta especial, cerradura con llave, o algún otro medio de seguridad, y que está bajo el control de la autoridad responsable del local. Varning! Denna enhet är avsedd för installation i områden med begränsat tillträde. Ett område med begränsat tillträde får endast tillträdas av servicepersonal med ett speciellt verktyg, lås och nyckel, eller annan säkerhetsanordning, och kontrolleras av den auktoritet som ansvarar för området.
Page 321 De onderstaande richtlijnen worden verstrekt om uw veiligheid te verzekeren: De Juniper Networks switch moet in een stellage worden geïnstalleerd die aan een bouwsel is verankerd. Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige in het rek is.
Page 322 Les directives ci-dessous sont destinées à assurer la protection du personnel: Le rack sur lequel est monté le Juniper Networks switch doit être fixé à la structure du bâtiment. Si cette unité constitue la seule unité montée en casier, elle doit être placée dans le bas.
Page 323 Para garantizar su seguridad, proceda según las siguientes instrucciones: El Juniper Networks switch debe instalarse en un bastidor fijado a la estructura del edificio. Colocar el equipo en la parte inferior del bastidor, cuando sea la única unidad en el mismo.
Page 324 Följande riktlinjer ges för att trygga din säkerhet: Juniper Networks switch måste installeras i en ställning som är förankrad i byggnadens struktur.
Page 325: Grounded Equipment Warning
Grounded Equipment Warning WARNING: The device is intended to be grounded. During normal use, ensure that you have connected earth ground to the chassis. Waarschuwing Deze apparatuur hoort geaard te worden Zorg dat de host-computer tijdens normaal gebruik met aarde is verbonden. Varoitus Tämä...
Page 326: Radiation From Open Port Apertures Warning
Radiation from Open Port Apertures Warning WARNING: Because invisible radiation might be emitted from the aperture of the port when no fiber cable is connected, avoid exposure to radiation and do not stare into open apertures. Waarschuwing Aangezien onzichtbare straling vanuit de opening van de poort kan komen als er geen fiberkabel aangesloten is, dient blootstelling aan straling en het kijken in open openingen vermeden te worden.
Page 327: Laser And Led Safety Guidelines And Warnings
Class 1 LED Product Warning | 332 Laser Beam Warning | 333 Juniper Networks devices are equipped with laser transmitters, which are considered a Class 1 Laser Product by the U.S. Food and Drug Administration and are evaluated as a Class 1 Laser Product per EN 60825-1 requirements.
Page 328: Class 1 Laser Product Warning
Class 1 Laser Product Warning WARNING: Class 1 laser product. Waarschuwing Klasse-1 laser produkt. Varoitus Luokan 1 lasertuote. Attention Produit laser de classe I. Warnung Laserprodukt der Klasse 1. Avvertenza Prodotto laser di Classe 1. Advarsel Laserprodukt av klasse 1. Aviso Produto laser de classe 1.
Page 329: Class 1 Led Product Warning
Class 1 LED Product Warning WARNING: Class 1 LED product. Waarschuwing Klasse 1 LED-product. Varoitus Luokan 1 valodiodituote. Attention Alarme de produit LED Class I. Warnung Class 1 LED-Produktwarnung. Avvertenza Avvertenza prodotto LED di Classe 1. Advarsel LED-produkt i klasse 1. Aviso Produto de classe 1 com LED.
Page 330: Laser Beam Warning
Laser Beam Warning WARNING: Do not stare into the laser beam or view it directly with optical instruments. Waarschuwing Niet in de straal staren of hem rechtstreeks bekijken met optische instrumenten. Varoitus Älä katso säteeseen äläkä tarkastele sitä suoraan optisen laitteen avulla. Attention Ne pas fixer le faisceau des yeux, ni l'observer directement à...
Page 331 Operating Temperature Warning | 339 Product Disposal Warning | 341 While performing the maintenance activities for devices, observe the following guidelines and warnings:...
Page 332: Battery Handling Warning
Battery Handling Warning WARNING: Replacing a battery incorrectly might result in an explosion. Replace a battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Waarschuwing Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen is.
Page 333: Jewelry Removal Warning
Jewelry Removal Warning...
Page 334 WARNING: Before working on equipment that is connected to power lines, remove jewelry, including rings, necklaces, and watches. Metal objects heat up when connected to power and ground and can cause serious burns or can be welded to the terminals. Waarschuwing Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen.
Page 335: Lightning Activity Warning
Varning! Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt hettas upp när de kopplas ihop med ström och jord och kan förorsaka allvarliga brännskador; metallobjekt kan också sammansvetsas med kontakterna. Lightning Activity Warning WARNING: Do not work on the system or connect or disconnect cables during periods...
Page 336: Operating Temperature Warning
Operating Temperature Warning...
Page 337 6 in. (15.2 cm) of clearance around the ventilation openings. Waarschuwing Om te voorkomen dat welke switch van de Juniper Networks router dan ook oververhit raakt, dient u deze niet te bedienen op een plaats waar de maximale aanbevolen omgevingstemperatuur van 40°...
Page 338: Product Disposal Warning
Varning! Förhindra att en Juniper Networks switch överhettas genom att inte använda den i ett område där den maximalt rekommenderade omgivningstemperaturen på 40° C överskrids. Förhindra att luftcirkulationen inskränks genom att se till att det finns fritt utrymme på minst 15,2 cm omkring ventilationsöppningarna.
Page 339: General Electrical Safety Guidelines And Warnings
General Electrical Safety Guidelines and Warnings WARNING: Certain ports on the device are designed for use as intrabuilding (within-the-building) interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed outside plant (OSP) cabling. To comply with NEBS requirements and protect against lightning surges and commercial power disturbances, the intrabuilding ports must not be metallically connected to interfaces that connect to the OSP or its wiring.
Page 340: Action To Take After An Electrical Accident
Operate the device within marked electrical ratings and product usage instructions. To ensure that the device and peripheral equipment function safely and correctly, use the cables and connectors specified for the attached peripheral equipment, and make certain they are in good condition. You can remove and replace many device components without powering off or disconnecting power to the device, as detailed elsewhere in the hardware documentation for this device.
Page 341 Always use an ESD wrist strap when you are handling components that are subject to ESD damage, and make sure that it is in direct contact with your skin. If a grounding strap is not available, hold the component in its antistatic bag (see Figure 174 on page 344) in one hand and touch the exposed, bare metal of the device with the other hand immediately before...
Page 342: Ac Power Electrical Safety Guidelines
AC Power Electrical Safety Guidelines CAUTION: For devices with AC power supplies, an external surge protective device (SPD) must be used at the AC power source. The following electrical safety guidelines apply to AC-powered devices: Note the following warnings printed on the device: “CAUTION: THIS UNIT HAS MORE THAN ONE POWER SUPPLY CORD.
Page 343: Ac Power Disconnection Warning
(CA). Varning! Innan du arbetar med ett chassi eller nära strömförsörjningsenheter skall du för växelströmsenheter dra ur nätsladden. DC Power Electrical Safety Guidelines for MX10008 Router This topic applies to hardware devices in the MX10008 router.
Page 344 To supply sufficient power, terminate the DC input wiring on a facility DC source that is capable of supplying: Minimum of 60 A at –48 VDC for MX10008 routers Incorporate an easily accessible disconnect device into the facility wiring. Be sure to connect the ground wire or conduit to a solid office earth ground.
Page 345: Dc Power Disconnection Warning
DC Power Disconnection Warning...
Page 346 WARNING: Before performing any of the DC power procedures, ensure that power is removed from the DC circuit. To ensure that all power is off, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the device handle of the circuit breaker in the OFF position.
Page 347: Dc Power Grounding Requirements And Warning
corrente contínua e coloque-o na posição OFF (Desligado), segurando nessa posição a manivela do interruptor do disjuntor com fita isoladora. ¡Atención! Antes de proceder con los siguientes pasos, comprobar que la alimentación del circuito de corriente continua (CC) esté cortada (OFF). Para asegurarse de que toda la alimentación esté...
Page 348 WARNING: When you install the device, the ground connection must always be made first and disconnected last. Waarschuwing Bij de installatie van het toestel moet de aardverbinding altijd het eerste worden gemaakt en het laatste worden losgemaakt. Varoitus Laitetta asennettaessa on maahan yhdistäminen aina tehtävä ensiksi ja maadoituksen irti kytkeminen viimeiseksi.
Page 349: Dc Power Wiring Sequence Warning
DC Power Wiring Sequence Warning...
Page 350 WARNING: Wire the DC power supply using the appropriate lugs. When connecting power, the proper wiring sequence is ground to ground, +RTN to +RTN, then –48 V to –48 V. When disconnecting power, the proper wiring sequence is –48 V to –48 V, +RTN to +RTN, then ground to ground.
Page 351 último. Observe que el alambre de tierra se debe conectar siempre primero y desconectar por último. ¡Atención! Wire a fonte de alimentação de DC Usando os talões apropriados na extremidade da fiação. Ao conectar a potência, a seqüência apropriada da fiação é moída para moer, +RTN a +RTN, então –48 V a –48 V.
Page 352: Dc Power Wiring Terminations Warning
DC Power Wiring Terminations Warning...
Page 353 WARNING: When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with upturned lugs. These terminations must be the appropriate size for the wires and must clamp both the insulation and conductor. Waarschuwing Wanneer geslagen bedrading vereist is, dient u bedrading te gebruiken die voorzien is van goedgekeurde aansluitingspunten, zoals het gesloten-lus type of het grijperschop type waarbij de aansluitpunten omhoog wijzen.
Page 354 hacia arriba. Estos terminales deberán ser del tamaño apropiado para los cables que se utilicen, y tendrán que sujetar tanto el aislante como el conductor. Varning! När flertrådiga ledningar krävs måste godkända ledningskontakter användas, t.ex. kabelsko av sluten eller öppen typ med uppåtvänd tapp. Storleken på dessa kontakter måste vara avpassad till ledningarna och måste kunna hålla både isoleringen och ledaren fastklämda.
Page 355: Multiple Power Supplies Disconnection Warning
Multiple Power Supplies Disconnection Warning WARNING: The network device has more than one power supply connection. All connections must be removed completely to remove power from the unit completely. Waarschuwing Deze eenheid heeft meer dan één stroomtoevoerverbinding; alle verbindingen moeten volledig worden verwijderd om de stroom van deze eenheid volledig te verwijderen.
Page 356: Tn Power Warning
TN Power Warning WARNING: The device is designed to work with a TN power system. Waarschuwing Het apparaat is ontworpen om te functioneren met TN energiesystemen. Varoitus Koje on suunniteltu toimimaan TN-sähkövoimajärjestelmien yhteydessä. Attention Ce dispositif a été conçu pour fonctionner avec des systèmes d'alimentation Warnung Das Gerät ist für die Verwendung mit TN-Stromsystemen ausgelegt.
Page 357: Compliance Statements For Emc Requirements For The Router
Safety CAN/CSA-C22.2 No. 60950-1 Information Technology Equipment - Safety EN 60950-1 Information Technology Equipment - Safety IEC 60825-1 IEC 60950-1 Information Technology Equipment - Safety CB Scheme report UL 60950-1 Information Technology Equipment - Safety EN 55022, Class A CISPR 22, Class A Australian Communications and Media Authority (ACMA) AS/NZS CISPR 22: Class A FCC Part 15, Subpart B, for Class A digital devices Industry Canada ICES 003, Class A...
Page 358: Canada
This topic describes the EMC requirements for the router: Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements.
Page 359: Japan
Translation from Hebrew–Warning: This product is Class A. In residential environments, the product may cause radio interference, and in such a situation, the user may be required to take adequate measures. Japan The preceding translates as follows: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Page 360: Compliance Statements For Environmental Requirements
The equipment is suitable for installation in a central office (CO). Compliance Statements for Environmental Requirements IN THIS SECTION MX10008 Compliance Statements for Acoustic Noise | 363 MX10016 Compliance Statements for Acoustic Noise | 363 MX10008 Compliance Statements for Acoustic Noise Maschinenlärminformations-Verordnung - 3.
Page 361 Translation: The emitted sound pressure is below 92 dB(A) per GR63 CORE.

Juniper MX10008 Hardware Manual

MX10008 System Overview

MX10008 Cooling System

MX10000 Power System

MX10008 Routing and Control Board Components and Descriptions

MX10008 Switch Fabric Board

Line Card (MX10K-LC2101)

2 Site Planning, Preparation, and Specifications

MX10008 Power Planning

MX10008 Transceiver and Cable Specifications

3 Initial Installation and Configuration

MX10008 Installation Overview

Unpacking the MX10008 Router and Components

Installing the Mounting Hardware

Installing the MX10008 into a Rack

Installing the Front Panel on an MX10008

Connecting the MX10000 to Power

Connecting the MX10008 to External Devices

Configuring an MX10008 Router

4 Maintaining Components

Field-Replaceable Units in an MX10008

Removing and Installing Routing and Control Boards

Removing and Installing MX10000 Power System Components

Removing and Installing MX10008 Switch Fabric Boards

Replacing an MPC

Removing and Installing Transceivers and Fiber-Optic Cables

5 Troubleshooting Hardware

Restoring Junos os

Alarm Messages

6 Contacting Customer Support and Returning the Chassis or Components

Contacting Customer Support

Returning the MX10008 Chassis or Components

7 Safety and Compliance Information

General Safety Guidelines and Warnings

Fire Safety Requirements

Installation Instructions Warning

MX10008 Chassis Lifting Guidelines

Restricted Access Warning

Ramp Warning

Rack-Mounting and Cabinet-Mounting Warnings

Grounded Equipment Warning

Radiation from Open Port Apertures Warning

Laser and LED Safety Guidelines and Warnings

Maintenance and Operational Safety Guidelines and Warnings

General Electrical Safety Guidelines and Warnings

Action to Take after an Electrical Accident

Prevention of Electrostatic Discharge Damage

AC Power Electrical Safety Guidelines

DC Power Grounding Requirements and Warning

DC Power Wiring Sequence Warning

DC Power Wiring Terminations Warning

Multiple Power Supplies Disconnection Warning

TN Power Warning

Agency Approvals and Compliance Statements

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Juniper MX10008

Summary of Contents for Juniper MX10008