Entry/Exit Lamp Unit; Removal; Installation; Time Delay Relay - Dodge Sprinter 2006 Manual

VA
Fig. 10 Entry/Exit Lamp Bulb Remove/Install
1 - LAMP HOUSING
2 - BULB HOLDER
3 - CONNECTOR
(4) Rem ove t h e bu lb fr om t h e bu lb h older.
INSTALLA TION
(1) In ser t t h e bu lb in t o t h e en t r y/exit la m p bu lb
h older (F ig. 10).
(2) Gr a sp t h e en t r y/exit la m p h ou sin g fir m ly in
on e h a n d, t h en in ser t t h e bu lb h older in t o t h e h ou s-
in g a n d r ot a t e it clockwise t o lock it in pla ce wit h t h e
ot h er h a n d.
(3) Rein st a ll t h e en t r y/exit la m p u n it in t o it s
m ou n t in g loca t ion . (Refer t o 8 - E LE CTRICAL/
LAMP S/LIGH TING
LAMP UNIT - INSTALLATION).
(4) Recon n ect t h e ba t t er y n ega t ive ca ble.
EN T RY / EX I T LAM P U N I T

REMOVAL

(1) Discon n ect a n d isola t e t h e ba t t er y n ega t ive
ca ble.
(2) In ser t t h e t ip of a sm a ll fla t -bla ded scr ewdr iver
in t o t h e n ot ch on on e edge of t h e en t r y/exit la m p
h ou sin g t o depr ess t h e r et a in er clip a n d pu ll t h a t
edge of t h e la m p a wa y fr om it s m ou n t in g loca t ion
(F ig. 11).
Fig. 11 Entry/Exit Lamp Unit Remove/Install
1 - STEP WELL SCUFF PAD
2 - NOTCH

3 - ENTRY/EXIT LAMP UNIT

(3) P u ll t h e en t r y/exit la m p u n it fr om it s m ou n t in g
loca t ion fa r en ou gh t o a ccess a n d discon n ect t h e veh i-
cle wir e h a r n ess fr om t h e la m p con n ect or r ecept a cle.
- INTE RIOR/E NTRY/E XIT
LAMPS/LIGHTING - INTERIOR 8L - 35
(4) Rem ove t h e en t r y/exit la m p u n it fr om it s
m ou n t in g loca t ion .
INSTALLA TION
(1) P osit ion t h e en t r y/exit la m p u n it t o it s m ou n t -
in g loca t ion .
(2) Recon n ect t h e veh icle wir e h a r n ess con n ect or
t o t h e en t r y/exit la m p con n ect or r ecept a cle (F ig. 11).
(3) P osit ion t h e edge of t h e en t r y/exit la m p h ou s-
in g opposit e fr om t h e r et a in er clip in t o t h e m ou n t in g
h ole.
(4) P u sh fir m ly a n d even ly on t h e n ot ch ed edge of
t h e en t r y/exit la m p h ou sin g u n t il t h e r et a in er clip
la t ch es in t o pla ce.
(5) Recon n ect t h e ba t t er y n ega t ive ca ble.
T I M E DELAY RELAY
REMOVAL
WARNING: To avoid personal injury or death, on
vehicles equipped with airbags, disable the supple-
mental restraint system before attempting any
steering wheel, steering column, airbag, seat belt
tensioner, or instrument panel component diagno-
sis or service. Disconnect and isolate the battery
negative (ground) cable, then wait two minutes for
the system capacitor to discharge before perform-
ing further diagnosis or service. This is the only
sure way to disable the supplemental restraint sys-
tem. Failure to take the proper precautions could
result in accidental airbag deployment.
(1) Discon n ect a n d isola t e t h e ba t t er y n ega t ive
ca ble.
(2) Move t h e dr iver side fr on t sea t t o it s m ost for-
wa r d posit ion for ea siest a ccess t o t h e sea t r iser
cover pa n el.
(3) Rem ove t h e t wo scr ews t h a t secu r e t h e cover
pa n el t o t h e t op of t h e sea t r iser u n der t h e dr iver
side fr on t sea t (F ig. 12).