Diagnosis And Testing - Instrument Cluster; Standard Procedure Cluster Programming - Dodge Sprinter 2006 Manual

VA
GROUNDS
Th e E MIC r eceives a n d su pplies a gr ou n d pa t h t o
sever a l swit ch es a n d sen sor s t h r ou gh t h e followin g
h a r d wir ed cir cu it s:
• Am bie n t
Te m p e ra tu re
(Op tio n a l)
• F u e l Le v e l S e n s o r Re tu rn
• Gro u n d
Refer t o t h e a ppr opr ia t e wir in g in for m a t ion for
a ddit ion a l det a ils.
COMMUNICA TION
Th e E MIC h a s pr ovision s for t h e followin g com m u -
n ica t ion cir cu it s:
• CAN D a ta B u s - Hig h
• CAN D a ta B u s - Lo w
• D ia g n o s tic S e ria l Co m m u n ic a tio n In te rfa c e
(S CI) D a ta B u s Lin e
Refer t o t h e a ppr opr ia t e wir in g in for m a t ion for
a ddit ion a l det a ils.
DIAGNOSIS AND TESTING - INSTRUMENT
CLUSTER
Th e h a r d wir ed in pu t s t o a n d ou t pu t s fr om t h e
in st r u m en t clu st er m a y be dia gn osed a n d t est ed
u sin g con ven t ion a l dia gn ost ic t ools a n d pr ocedu r es.
Refer t o t h e a ppr opr ia t e wir in g in for m a t ion . Th e wir-
in g in for m a t ion in clu des wir in g dia gr a m s, pr oper
wir e a n d con n ect or r epa ir pr ocedu r es, det a ils of wir e
h a r n ess r ou t in g a n d r et en t ion , con n ect or pin -ou t
in for m a t ion a n d loca t ion views for t h e va r iou s wir e
h a r n ess con n ect or s, splices a n d gr ou n ds.
If t h e in st r u m en t clu st er is com plet ely in oper a t ive,
be cer t a in t o ch eck t h e fu sed B(+) cir cu it fu ses a n d
wir in g for t h e in st r u m en t clu st er. If t h e clu st er gen -
er a l illu m in a t ion is in oper a t ive, be cer t a in t o ch eck
t h e in st r u m en t ligh t in g fu se a n d t h e in pu t cir cu it t o
t h e in st r u m en t clu st er fr om t h e ext er ior ligh t in g cir-
cu it r y of t h e m u lt i-fu n ct ion swit ch on t h e st eer in g
colu m n .
Con ven t ion a l dia gn ost ic m et h ods m a y n ot pr ove
con clu sive in t h e dia gn osis of t h e in st r u m en t clu st er.
In or der t o obt a in con clu sive t est in g of t h e in st r u -
m en t clu st er, t h e Con t r oller Ar ea Net wor k (CAN)
da t a bu s n et wor k a n d a ll of t h e elect r on ic m odu les
t h a t pr ovide in pu t s t o or r eceive ou t pu t s fr om t h e
in st r u m en t clu st er m u st a lso be ch ecked. Th e m ost
r elia ble, efficien t , a n d a ccu r a t e m ea n s t o dia gn ose
t h e in st r u m en t clu st er, t h e CAN da t a bu s n et wor k,
a n d t h e elect r on ic m odu les t h a t pr ovide in pu t s t o or
r eceive ou t pu t s fr om t h e in st r u m en t clu st er r equ ir es
t h e u se of a dia gn ost ic sca n t ool a n d t h e a ppr opr ia t e
dia gn ost ic in for m a t ion . Th e dia gn ost ic sca n t ool ca n
pr ovide con fir m a t ion t h a t t h e CAN da t a bu s n et wor k
is fu n ct ion a l, t h a t a ll of t h e m odu les a r e sen din g a n d
r eceivin g t h e pr oper elect r on ic m essa ges over t h e
CAN da t a bu s, a n d t h a t t h e in st r u m en t clu st er is
S e n s o r Re tu rn
INSTRUMENT CLUSTER 8J - 7
r eceivin g t h e pr oper h a r d wir ed in pu t s a n d r espon d-
in g wit h t h e pr oper h a r d wir ed ou t pu t s n eeded t o
per for m it s m a n y fu n ct ion s.
WARNING: To avoid personal injury or death, on
vehicles equipped with airbags, disable the supple-
mental restraint system before attempting any
steering wheel, steering column, airbag, seat belt
tensioner, or instrument panel component diagno-
sis or service. Disconnect and isolate the battery
negative (ground) cable, then wait two minutes for
the system capacitor to discharge before perform-
ing further diagnosis or service. This is the only
sure way to disable the supplemental restraint sys-
tem. Failure to take the proper precautions could
result in accidental airbag deployment.
STAN DARD PROCEDU RE
CLUSTER PROGRAMMING
NOTE: After replacing the Instrument Cluster (IC)
according to the service procedures, determine the
optional equipment on the vehicle by accessing the
sales code information using the Vehicle Identifica-
tion Number (VIN) on DealerCONNECT.
(1) Usin g t h e DRBIII , select MIS CELLAN EOU S
F U N CTION S in t h e In st r u m en t Clu st er (IC) sect ion .
(2) Select MOD U LE
MEN T.
(3) F ollowin g t h e pr om pt s on t h e DRBIII , en t er
t h e cor r ect pa r a m et er s t h a t a r e a pplica ble t o t h e
veh icle. Use t h e sa les code in for m a t ion a n d visu a l
in spect ion t o obt a in t h e cor r ect pa r a m et er s.
CAUTION: Do not lock down the instrument cluster
until the following steps are followed or the instru-
ment cluster may be irreversibly damaged.
(4) Aft er en t er in g t h e pr oper pa r a m et er s in t o t h e
IC, t u r n t h e ign it ion swit ch t o t h e OF F posit ion for
30 secon ds, t h en t u r n t h e ign it ion swit ch ON.
(5) Test dr ive t h e veh icle for a t lea st 10 m in u t es
befor e pr oceedin g.
(6) Ch eck ALL m odu les for a n y pa r a m et er iza t ion
DTCs. If a n y pa r a m et er iza t ion DTCs a r e pr esen t , on e
or m or e pa r a m et er s en t er ed in t o t h e IC a r e in cor r ect .
Ver ify a ll pa r a m et er s en t er ed u sin g t h e sa les code
in for m a t ion a n d visu a l in spect ion of t h e veh icle.
(7) If t h e pa r a m et er s en t er ed a r e ver ified a s cor-
r ect a n d pa r a m et er iza t ion DTCs a r e st ill pr esen t ,
r efer t o t h e a ppr opr ia t e dia gn ost ic in for m a t ion .
(8) If n o pa r a m et er iza t ion DTCs a r e pr esen t , lock
down t h e IC.
S ERVICE REP LACE-