Lam Ps / Li Gh T I N G - Ex T Eri Or; Front Lamp Unit Removal; Installation - Dodge Sprinter 2006 Manual

VA
Fig. 17 Fog Lamp Switch Remove/Install
1 - FOG LAMP SWITCH
2 - LATCH (2)
3 - CLUSTER BEZEL
(4) Rem ove t h e fog la m p swit ch fr om t h e fa ce of
t h e clu st er bezel.
INSTALLA TION
WARNING: To avoid personal injury or death, on
vehicles equipped with airbags, disable the supple-
mental restraint system before attempting any
steering wheel, steering column, airbag, seat belt
tensioner, or instrument panel component diagno-
sis or service. Disconnect and isolate the battery
negative (ground) cable, then wait two minutes for
the system capacitor to discharge before perform-
ing further diagnosis or service. This is the only
sure way to disable the supplemental restraint sys-
tem. Failure to take the proper precautions could
result in accidental airbag deployment.
(1) P osit ion t h e fog la m p swit ch t o t h e pr oper
m ou n t in g h ole on t h e fa ce of t h e clu st er bezel (F ig.
16).
(2) Usin g h a n d pr essu r e, pu sh t h e fog la m p swit ch
fir m ly a n d even ly in t o t h e swit ch m ou n t in g h ole of
t h e clu st er bezel u n t il bot h of t h e la t ch es on t h e
swit ch body a r e fu lly en ga ged.
(3) Rein st a ll t h e clu st er bezel on t o t h e in st r u m en t
pa n el. (Refer t o 23 - BODY/INSTRUME NT PANE L/
CLUSTE R BE ZE L - INSTALLATION).
(4) Recon n ect t h e ba t t er y n ega t ive ca ble.
FRON T LAM P U N I T
REMOVAL
(1) Discon n ect a n d isola t e t h e ba t t er y n ega t ive
ca ble.
(2) Rem ove t h e fr on t gr ille fr om t h e veh icle. (Refer
t o 23 - BODY/E XTE RIOR/GRILLE - RE MOVAL).
LAMPS/LIGHTING - EXTERIOR 8L - 13
(3) Rem ove t h e t wo scr ews t h a t secu r e t h e cover a t
t h e in boa r d side of t h e fr on t la m p u n it (F ig. 18).
Fig. 18 Front Lamp Unit Remove/Install
1 - SCREW (2)
2 - COVER
3 - SCREW (4)
4 - LAMP UNIT
5 - WIRE HARNESS CONNECTOR
(4) Rem ove t h e cover fr om t h e fr on t la m p u n it .
(5) F r om t h e en gin e com pa r t m en t , discon n ect t h e
veh icle wir e h a r n ess con n ect or fr om t h e con n ect or
r ecept a cle for t h e fr on t la m p u n it .
(6) Rem ove t h e fou r scr ews t h a t secu r e t h e fr on t
la m p u n it t o t h e fr on t of t h e veh icle.
(7) Rem ove t h e fr on t la m p u n it fr om t h e fr on t of
t h e veh icle.
INSTALLA TION
(1) P osit ion t h e fr on t la m p u n it t o t h e fr on t of t h e
veh icle (F ig. 18).
(2) In st a ll a n d t igh t en t h e fou r scr ews t h a t secu r e
t h e fr on t la m p u n it t o t h e fr on t of t h e veh icle.
(3) F r om t h e en gin e com pa r t m en t , r econ n ect t h e
veh icle wir e h a r n ess con n ect or t o t h e con n ect or
r ecept a cle for t h e fr on t la m p u n it .
(4) P osit ion t h e cover t o t h e fr on t la m p u n it .
(5) In st a ll a n d t igh t en t h e t wo scr ews t h a t secu r e
t h e cover a t t h e in boa r d side of t h e fr on t la m p u n it .
(6) Rein st a ll t h e fr on t gr ille on t o t h e veh icle.
(Refer t o 23 - BODY/E XTE RIOR/GRILLE - INSTAL-
LATION).
(7) Recon n ect t h e ba t t er y n ega t ive ca ble.
(8) Ch eck a n d a dju st t h e fr on t la m p a lign m en t a s
r equ ir ed. (Refer t o 8 - E LE CTRICAL/LAMP S/LIGH T-
ING - E XTE RIOR/F RONT LAMP UNIT - ADJ UST-
ME NTS).