Installation; Rear Seat Belt & Retractor Removal - Dodge Sprinter 2006 Manual

8O - 28 RESTRAINTS
Fig. 30 Passenger Airbag Bracket Remove/Install
1 - BRACKET
2 - STRUCTURAL SUPPORT
3 - SCREW (4)
(3) Rem ove t h e pa ssen ger a ir ba g br a cket fr om t h e
in st r u m en t pa n el st r u ct u r a l su ppor t .
INSTALLA TION
WARNING: To avoid personal injury or death, on
vehicles equipped with airbags, disable the supple-
mental restraint system before attempting any
steering wheel, steering column, airbag, seat belt
tensioner, impact sensor, or instrument panel com-
ponent diagnosis or service. Disconnect and isolate
the battery negative (ground) cable, then wait two
minutes for the system capacitor to discharge
before performing further diagnosis or service. This
is the only sure way to disable the supplemental
restraint system. Failure to take the proper precau-
tions could result in accidental airbag deployment.
(1) P osit ion t h e pa ssen ger a ir ba g br a cket on t o t h e
in st r u m en t pa n el st r u ct u r a l su ppor t (F ig. 30).
(2) In st a ll a n d t igh t en t h e fou r scr ews t h a t secu r e
t h e pa ssen ger a ir ba g br a cket t o t h e in st r u m en t pa n el
st r u ct u r a l su ppor t . Tigh t en t h e scr ews t o 10 N·m (89
in . lbs.).
(3) Rein st a ll t h e pa ssen ger a ir ba g in t o t h e in st r u -
m en t pa n el. (Refer
STRAINTS/PASSE NGE R

INSTALLATION).

REAR SEAT BELT & RET RAC-
T OR
REMOVAL
WARNING: To avoid personal injury or death, during
and following any seat belt service, carefully
inspect all seat belts, buckles, mounting hardware,
t o 8 - E LE CTRICAL/RE -
AIRBAG
retractors, and anchors for proper installation, oper-
ation, or damage. Replace any belt that is cut,
frayed, or torn. Straighten any belt that is twisted.
Tighten any loose fasteners. Replace any belt that
has a damaged or inoperative buckle or retractor.
Replace any belt that has a bent or damaged latch
plate or anchor plate. Never attempt to repair a seat
belt component. Always replace damaged or faulty
seat belt components with the correct, new and
unused replacement
DaimlerChrysler Mopar Parts Catalog.
(1) Rem ove t h e r ea r ben ch sea t con t a in in g t h e r ea r
sea t belt a n d r et r a ct or u n it t o be ser viced fr om t h e
veh icle.
(2) Lift t h e sea t belt webbin g t o a ccess a n d r em ove
t h e pla st ic pu sh pin fa st en er t h a t secu r es t h e r ea r
sea t belt t u r n in g loop t r im cover t o t h e t u r n in g loop
br a cket a t t h e t op of t h e sea t ba ck (F ig. 31).
Fig. 31 Turning Loop Trim Cover
1 - TRIM COVER
2 - SEAT BELT
3 - RETAINER
4 - REAR SEAT BACK
(3) Rem ove t h e t u r n in g loop t r im cover fr om t h e
t u r n in g loop br a cket .
(4) Rem ove t h e pu sh n u t a t t h e ba ck of t h e t u r n -
in g loop br a cket t h a t secu r es t h e pin on wh ich t h e
t wo t u r n in g loops pivot (F ig. 32).
-
parts listed in
VA
the