Dodge Sprinter 2006 Manual page 715

VA
Do n ot blen d ot h er specific fu el a ddit ives wit h die-
sel fu el. Th ey on ly r esu lt in u n n ecessa r y cost , a n d
m a y be h a r m fu l t o t h e en gin e oper a t ion .
POWER STEERING FLUID
No flu id ser vice r equ ir ed. F illed wit h P ower St eer-
in g F lu id a ppr oved t o MB 236.3, su ch a s Mobil
ATF -D (E xxon Mobil Cor por a t ion ) or equ iva len t .
OPERA TION - AUTOMA TIC TRANSMISSION
FLUID
Th e a u t om a t ic t r a n sm ission flu id is select ed ba sed
u pon sever a l qu a lit ies. Th e flu id m u st pr ovide a h igh
level of pr ot ect ion for t h e in t er n a l com pon en t s by
pr ovidin g a lu br ica t in g film bet ween a dja cen t m et a l
com pon en t s. Th e flu id m u st a lso be t h er m a lly st a ble
so t h a t it ca n m a in t a in a con sist en t viscosit y t h r ou gh
a la r ge t em per a t u r e r a n ge. If t h e viscosit y st a ys con -
st a n t t h r ou gh t h e t em per a t u r e r a n ge of oper a t ion ,
t r a n sm ission oper a t ion a n d sh ift feel will r em a in con -
sist en t . Tr a n sm ission flu id m u st a lso be a good con -
du ct or of h ea t . Th e flu id m u st a bsor b h ea t fr om t h e
in t er n a l t r a n sm ission com pon en t s a n d t r a n sfer t h a t
h ea t t o t h e t r a n sm ission ca se.
FLU I D CAPACI T I ES
SPECIFICA TIONS - FLUID CAPACITIES
DESCRIPTION
ENGINE COOLANT
10 Liters
ENGINE OIL
9.0L without Filter Re-
placement
AUTOMATIC TRANSMISSION
Service Fill - NAG1
O-haul Fill - NAG1
Dry fill capacity Depending on type and size of inter-
nal cooler, length and inside diameter of cooler lines,
or use of an auxiliary cooler, these figures may vary.
(Refer to appropriate 21 - TRANSMISSION/AUTO-
MATIC/FLUID - STANDARD PROCEDURE).
REAR AXLE ±.03L (1 oz.)
8 1/2
FUEL TANK
Primary
Reserve
*Nominal refill capacities are shown. A variation may
be observed from vehicle to vehicle due to manufac-
turing tolerance and refill procedure
SPECIFICATION
10.5 Quarts
9.5 Quarts with Filter
Replacement
5.0 L (10.6 pts.)
7.7 L (16.3 pts.)
1.8 L (4.0 pts.)
100 L (26.4 gal.)*
10.5 L (2.8 gal.)*
LUBRICA TION & MAINTENANCE 0 - 5
DESCRIPTION
POWER STEERING SYSTEM
Power steering fluid capacities are dependent on
engine/chassis options as well as steering gear/cool-
er options. Depending on type and size of internal
cooler, length and inside diameter of cooler lines, or
use of an auxiliary cooler, these capacities may vary.
Refer to 19, Steering for proper fill and bleed proce-
FLU I D FI LL / CH ECK LOCA-
T I ON S
INSPECTION - FLUID FILL / CHECK LOCA-
TIONS
Th e flu id fill/ch eck loca t ion s a n d lu br ica t ion poin t s
a r e loca t ed in ea ch a pplica ble gr ou p.
H OI ST I N G
STANDARD PROCEDURE - HOISTING
Refer t o t h e Own er 's Ma n u a l for em er gen cy veh icle
lift in g pr ocedu r es.
WARNING: THE HOISTING AND JACK LIFTING
POINTS PROVIDED ARE FOR A COMPLETE VEHI-
CLE. WHEN A CHASSIS OR DRIVETRAIN COMPO-
NENT IS REMOVED FROM A VEHICLE, THE
CENTER OF GRAVITY IS ALTERED MAKING SOME
HOISTING CONDITIONS UNSTABLE. PROPERLY
SUPPORT OR SECURE VEHICLE TO HOISTING
DEVICE WHEN THESE CONDITIONS EXIST.
FLOOR JACK
Wh en pr oper ly posit ion ed, a floor ja ck ca n be u sed
t o lift a veh icle. Su ppor t t h e veh icle in t h e r a ised
posit ion wit h ja ck st a n ds a t t h e fr on t a n d r ea r en ds
of t h e fr a m e r a ils.
CAUTION: Do not lift vehicle with a floor jack posi-
tioned under:
• An axle tube.
• A body side sill.
• A steering linkage component.
• A drive shaft.
• The engine or transmission oil pan.
• The fuel tank.
• A front suspension arm.
SPECIFICATION
dures.