Installation; Headlamp Leveling Switch Removal - Dodge Sprinter 2006 Manual

VA
Fig. 28 Headlamp Leveling Motor Remove/Install
1 - PUSHROD
2 - MOTOR
3 - MOUNT
4 - BRACKET
5 - REFLECTOR
(5) St a bilize t h e fr on t la m p u n it r eflect or wit h on e
h a n d, t h en u se t h e ot h er h a n d t o pu ll t h e h ea dla m p
levelin g m ot or a wa y fr om t h e r eflect or u n t il t h e ba ll
on t h e en d of t h e m ot or pu sh r od u n sn a ps fr om t h e
br a cket on t h e r eflect or.
(6) Rem ove t h e h ea dla m p levelin g m ot or fr om t h e
m ou n t on t h e fr on t la m p u n it h ou sin g.
INSTALLA TION
(1) P osit ion t h e h ea dla m p levelin g m ot or t o t h e
m ou n t on t h e fr on t la m p u n it h ou sin g (F ig. 28).
(2) Sn a p t h e ba ll on t h e en d of t h e h ea dla m p lev-
elin g m ot or in t o t h e br a cket on t h e fr on t la m p u n it
r eflect or.
(3) P u sh t h e h ea dla m p levelin g m ot or in t o t h e
m ou n t in t egr a l t o t h e fr on t la m p u n it h ou sin g u n t il it
is fu lly sea t ed, t h en r ot a t e t h e m ot or clockwise a bou t
30 degr ees t o lock it in t o pla ce (F ig. 27).
(4) Recon n ect t h e fr on t la m p u n it wir e h a r n ess
con n ect or t o t h e con n ect or r ecept a cle for t h e h ea d-
la m p levelin g m ot or.
(5) P osit ion t h e fr on t la m p u n it r ea r cover on t o t h e
la m p h ou sin g a n d en ga ge t h e r et a in er s over ea ch
side of t h e cover t o secu r e it (F ig. 26).
(6) Recon n ect t h e ba t t er y n ega t ive ca ble.
H EADLAM P LEV ELI N G
SWI T CH
REMOVAL
WARNING: To avoid personal injury or death, on
vehicles equipped with airbags, disable the supple-
mental restraint system before attempting any
steering wheel, steering column, airbag, seat belt
LAMPS/LIGHTING - EXTERIOR 8L - 17
tensioner, or instrument panel component diagno-
sis or service. Disconnect and isolate the battery
negative (ground) cable, then wait two minutes for
the system capacitor to discharge before perform-
ing further diagnosis or service. This is the only
sure way to disable the supplemental restraint sys-
tem. Failure to take the proper precautions could
result in accidental airbag deployment.
(1) Discon n ect a n d isola t e t h e ba t t er y n ega t ive
ca ble.
(2) Rem ove t h e clu st er bezel fr om t h e in st r u m en t
pa n el (F ig. 29). (Refer t o 23 - BODY/INSTRUME NT
PANE L/CLUSTE R BE ZE L - RE MOVAL).
Fig. 29 Headlamp Leveling Switch
1 - HEADLAMP LEVELING SWITCH
2 - SCREW (2)
3 - CLUSTER BEZEL
4 - TO REAR WINDOW DEFOGGER SWITCH (OPTIONAL)
5 - TO HEADLAMP LEVELING SWITCH
6 - TO FOG LAMP SWITCH (OPTIONAL)
(3) F r om t h e ba ck of t h e clu st er bezel, squ eeze t h e
t wo la t ch es on t h e h ea dla m p levelin g swit ch body
a n d pu sh t h e swit ch ou t t h r ou gh t h e fa ce of t h e bezel
(F ig. 30).