Installation; High Beam Headlamp Bulb Removal - Dodge Sprinter 2006 Manual

8L - 18 LAMPS/LIGHTING - EXTERIOR
Fig. 30 Headlamp Leveling Switch Remove/Install
1 - SWITCH
2 - LATCH (2)
3 - CLUSTER BEZEL
(4) Rem ove t h e h ea dla m p levelin g swit ch fr om t h e
fa ce of t h e clu st er bezel.
INSTALLA TION
WARNING: To avoid personal injury or death, on
vehicles equipped with airbags, disable the supple-
mental restraint system before attempting any
steering wheel, steering column, airbag, seat belt
tensioner, or instrument panel component diagno-
sis or service. Disconnect and isolate the battery
negative (ground) cable, then wait two minutes for
the system capacitor to discharge before perform-
ing further diagnosis or service. This is the only
sure way to disable the supplemental restraint sys-
tem. Failure to take the proper precautions could
result in accidental airbag deployment.
(1) P osit ion t h e h ea dla m p levelin g swit ch t o t h e
pr oper m ou n t in g h ole on t h e fa ce of t h e clu st er bezel
(F ig. 29).
(2) Usin g h a n d pr essu r e, pu sh t h e h ea dla m p level-
in g swit ch fir m ly a n d even ly in t o t h e swit ch m ou n t -
in g h ole of t h e clu st er bezel u n t il bot h of t h e la t ch es
on t h e swit ch body a r e fu lly en ga ged.
(3) Rein st a ll t h e clu st er bezel on t o t h e in st r u m en t
pa n el. (Refer t o 23 - BODY/INSTRUME NT PANE L/
CLUSTE R BE ZE L - INSTALLATION).
(4) Recon n ect t h e ba t t er y n ega t ive ca ble.
H I GH BEAM H EADLAM P BU LB
REMOVAL
(1) Discon n ect a n d isola t e t h e ba t t er y n ega t ive
ca ble.
(2) Disen ga ge a n d swin g t h e r et a in er s t h a t secu r e
t h e fr on t la m p u n it r ea r cover t o ea ch side of t h e
la m p h ou sin g a n d r em ove t h e cover (F ig. 31).
Fig. 31 Front Lamp Unit Bulbs Remove/Install
1 - COVER RETAINER (2)
2 - BULB RETAINER (3)
3 - FOG LAMP BULB (OPTIONAL)
4 - COVER
5 - LOW BEAM BULB
6 - POSITION BULB
7 - HIGH BEAM BULB
8 - TURN/PARK/SIDE MARKER BULB
9 - FRONT LAMP UNIT
(3) Discon n ect t h e fr on t la m p u n it wir e h a r n ess
con n ect or fr om t h e h igh bea m h ea dla m p bu lb ba se
(F ig. 32).
Fig. 32 High Beam Headlamp Bulb Remove/Install
1 - LAMP HOUSING
2 - BULB RETAINER
3 - CONNECTOR
4 - BULB BASE
(4) Disen ga ge t h e h igh
r et a in er by pu sh in g it sligh t ly t owa r d t h e fr on t la m p
u n it h ou sin g a n d ou t wa r d fr om t h e bu lb ba se, t h en
pivot t h e r et a in er off of t h e bu lb ba se.
(5) Rem ove t h e h igh bea m h ea dla m p bu lb fr om t h e
in t egr a l bu lb h older on t h e fr on t la m p u n it r eflect or.
VA
bea m h ea dla m p bu lb