Aileron Control Cables Installation - Piper PA-24 Comanche Service Manual

•
•
•
PtPER COMANCHE SERVICE MANUAL
by removinj( cotter pin. nut. wuber and ,clevis bolt or by
disulemblin,
the turnbuckle.
4.
Remove the cotter pin cable
pard
from the cable pulley by racbitlJ tbroulh the access hole
in each wing at sation 115.50.
S.
Remove the cotter pin cable
pards
from the left and riJbt puOeys of the bal&ncc cable at
fusclace sution 13$.0.
6. If
an
AutoPilot roU
servo
is
a.a:adlal to the bl1ancc cable.
remove
the slot bead
screws
from
the bridle cable clamps at the
center
of the fue• .
Remove
the safety slcna iIlboard of each clamp.
1. Draw the cable throUJh the
fuselap
ad each
wiDJ.
Usc caution _heD
drawiaJ
the end of the
cable through the rub block at
wiftJ
sation 78.0.
5·10.
IosaI1a1:iOft
Of
ADINIl CODenl
Cabla.
(Refer
to Fipre
'·2.)
&.
Installation of the aileron balance cable may be accomp1isbecl by the foUowillJ procedure:
1. Draw the baJance cable (4) into each
wiDe
from the center of the f\ISc1qc.
2. With the cable positioned on both the left and rilht puOeys ill the fusclace at station 135.0.
insull the cotter pin able
JUUds.
3.
Amch the ends of the cable to the forwud end of the beUc:rank in each
willi
by assemblinr
nunbuc:kJes and/or sccurinJ with clms bolt. waber, nut and cotter pin. Do
not
set
cable tension at this
time.
NOTE
Do not
tiJhten
aambuckle fork ends
Oft
bellcruak so a,ht that tbe end
cannot rotate.
4.
By rftChinl throUJh the access opcnin, in each
willi
at nation 115.5. position the able
uound the upper puOey of the cluster and if the primary control cable i. iastaUed. insall the cotter pill
cable guard.
5. If an autopilot roD
1CtY0
is
part of the airplane's equipment. attach the bridle cable to the
balance cable with the usc of the iDRallation inm\IetiODl pen in ElectrOnics Section.
b. Installation of the left andlor ",ht primary contrOl cables (3 and 6) thu lad from the fuselage
into the
winp
may be accomplished by the foUowiDJ procedure:
1. Dnw the cable throup the wint intO the
twc...
2. Install the cable puUey in the fuse• • forward of the rear spar suppon bulkhead at sution
135.0. For the left pulley, position the cable and' puDer and secure with bolt, wubcr and GUt. For the riPt
pulley. position the cable and puUey in the bracket
and
_CUR
puUey with bolt. wubcr and nut. and then
attach the bracket assembly to the bortom skin of the
fUsdatc
and spar suppan bulkhead
usinJ
screws.
Ascertain
that corter pin cable
pards
1ft
installed.
3. If the right cable (6)
was
removed. position the cable
and instaU
the pulley
in
the bncket
located on the butt aft end of the wiftl by
usi.nI
bolt, wabet and nut.
4-.
Tbroqh the access hole
in
the
wiDe
at
station 115.5, position the cable on the lower pulley of
the cluster and install the corter pin cable pard.
,. Attach the cable to the aft end of the cable bcUcrank by asscmblinl turnbuckle and/or
securing with clevis bolt. wuhcr. nut ad cotter pin.
NOTE
Do not tilhten turnbuckle fork end. on the bcllcrank so titht that the
end cannot rotate.
SURFACE CONTROLS
ISSUeD:
8118n2
IGI