Piper PA-24 Comanche Service Manual page 96

PIPER COMANCHE SERVICE MANUAL
TABLE III-I. INSPECTION REPORT (cont.)
•
1D22
REVISED. II/J/82
Inspection Time (hrs.)
Nature of Inspection
SO
100 500 1000
B.
ENGINE GROUP (eent.)
28. Inspect intake seals for leaks and clamps for tightness
. . . II . . . . . . . . . . .
ill."" ........
0 0 0
i
29. Inspectcondition of flexible fuel lines (See
~ote
17) ....................
0 0 0
30. Replace flexible fuel lines (Sec '\:ote 17)
. . . . . III . . . . III . . . . . . . . . . . . . . . . . . . . . . . .
0
31. Inspect fuel system for leaks ..............................•.......... 0 0
0
32. Inspect and lubricate fuel selector valve (PA-24-180 and
250 per latest Piper Service Bulletin No. 354)
(See Note 13 &
J
5)...............................•.................
0 0 0
I
33. Clean screens in electric fuel pump(s) (Plunger type pump) .............. 0 0 0 0
34. Check fuel pumps for operation (Engine driven and electric) .......•...•.
0 0 0
35. Overhaul or replace fuel pumps (Engine driven and electric)
(See Note 6)...•...........•.........•..................•.••...•..• 0
I
0 0
36. Inspect vacuum pumps and lines ..................................... 0
i
0 0
37. Overhaul or replace vacuum pumps (See Note 6) ......•••.....•.•..••.•
I
i
0
38. Inspect throttle, carburetor heat or alternate air, mixture
I
I
and propeller governor controls for travel and operating
condition ................................•......•.................
I
0 0 0
39. Inspect exhaust stacks, connections and gaskets (Refer to PA-24
•
Service Manual, Section Ill) (Replace gaskets as required) ..............
0
I
0 0
40. Inspect muffler. heat exchanger and baffles (Refer to PA-24
Service Manual, Section Ill)
.. III . . . . . . . . III . . . . . III . . . . . . . " . . . . . . II . . . . . . . . " " . . . . . . . . . . . . . . . . . . . . . . . . . .
0 0
0
41. Inspect bressher tube for obstructions and security ..................... 0 0
0
42. Inspect crankcase for cracks, leaks and security of seam bolts 0 0 0
43. Inspect engine mounts for cracks and loose mounting ..................•
0 0 0
44. Inspect rubber engine mount bushings for deterioration
I
(Replace every 500 hours) .........•................................. 0
0 0
45. Inspect all engine baffles for cracks ................................... 0
0 0
46. Inspect firewall for cracks ........................•...•..•••..••....•.
0 0 0
47. Inspect condition of firewall seals ....................................
1
0
0 0
i
48. Inspect condition and tension of generator or alternator drive
I
belt ......
I . . . . . . . . " . . . . . . . . . . . . . . . . " oil It . . . . III 110 . . . . . . . . . . . . . . . . . III . . . " . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0 0
0
49. Inspect condition of generator or alternator and starter .................
0
0 0
SO. Lubricate all controls per lubrication chart in Service Manual ........... 0
0 0
5 l. Overhaul or replace propeller governor (Refer to latest revision
Hartzell Service Letter No. 61) ......................................
0
52. Complete overhaul of engine or replace with factory rebuilt
(See Note 6)...............................................•.......
0
53. Reinstall engine cowl ..............................•................
0 0
0
INSPECTI