Leica TPS1200 Series Reference Manual page 198

GeoCOM Reference Manual
GRC_EDM_SLDR_UNSUPPORTED
GRC_EDM_UNKNOW_ERR
GRC_EDM_DISTRANGE_ERR
GRC_EDM_SIGNTONOISE_ERR
GRC_EDM_NOISEHIGH_ERR
GRC_EDM_PWD_NOTSET
GRC_EDM_ACTION_NO_MORE_VALID
GRC_EDM_MULTRG_ERR
GRC_EDM_MISSING_EE_CONSTS
GRC_EDM_NOPRECISE
GRC_EDM_MEAS_DIST_NOT_ALLOWED
TMC
RetCodeName
GRC_TMC_NO_FULL_CORRECTION
GRC_TMC_ACCURACY_GUARANTEE
GRC_TMC_ANGLE_OK
GRC_TMC_ANGLE_NOT_FULL_CORR
GRC_TMC_ANGLE_NO_ACC_GUARANTY
GRC_TMC_ANGLE_ERROR
GRC_TMC_DIST_PPM
GRC_TMC_DIST_ERROR
GRC_TMC_BUSY
GRC_TMC_SIGNAL_ERROR
MOT
RetCodeName
GRC_MOT_UNREADY
GRC_MOT_BUSY
GRC_MOT_NOT_OCONST
GRC_MOT_NOT_CONFIG
GRC_MOT_NOT_POSIT
GRC_MOT_NOT_SERVICE
GRC_MOT_NOT_BUSY
GRC_MOT_NOT_LOCK
GRC_MOT_NOT_SPIRAL
GRC_MOT_V_ENCODER
GRC_MOT_HZ_ENCODER
GRC_MOT_HZ_V_ENCODER
BMM
RetCodeName
GRC_BMM_XFER_PENDING
GRC_BMM_NO_XFER_OPEN
GRC_BMM_UNKNOWN_CHARSET
GRC_BMM_NOT_INSTALLED
GRC_BMM_ALREADY_EXIST
GRC_BMM_CANT_DELETE
Leica TPS1200 – Version 1.50
804 0x324
808 0x328
818 0x332
819 0x333
820 0x334
821 0x335
822 0x336
823 0x337
824 0x338
825 0x339
826 0x33A
1280 0x500
Value HexVal
1283 0x503
1284 0x504
1285 0x505
1288 0x508
1289 0x509
1290 0x50A
1291 0x50B
1292 0x50C
1293 0x50D
1294 0x50E
1792 0x700
Value HexVal
1792 0x700
1793 0x701
1794 0x702
1795 0x703
1796 0x704
1797 0x705
1798 0x706
1799 0x707
1800 0x708
1801 0x709
1802 0x70A
1803 0x70B
2304 0x900
Value HexVal
2305 0x901
2306 0x902
2307 0x903
2308 0x904
2309 0x905
2310 0x906
Return-Code names and return-code values
Current (loaded) firmware doesn't support
upload.
Undocumented error from the EDM sensor,
should not occur.
Out of distance range (dist too small or large)
Signal to noise ratio too small
Noise to high
Password is not set
Elapsed time between prepare und start fast
measurement for ATR to long
Possibly more than one target (also a sensor
error)
eeprom consts are missing
No precise measurement possible
Measured distance is to big (not allowed)
Description
Warning: measurement without full correction
Info: accuracy can not be guarantee
Warning: only angle measurement valid
Warning: only angle measurement valid but
without full correction
Info: only angle measurement valid but
accuracy can not be guarantee
Error: no angle measurement
Error: wrong setting of PPM or MM on EDM
Error: distance measurement not done (no aim,
etc.)
Error: system is busy (no measurement done)
Error: no signal on EDM (only in signal mode)
Description
motorization is not ready
motorization is handling another task
motorization is not in velocity mode
motorization is in the wrong mode or busy
motorization is not in posit mode
motorization is not in service mode
motorization is handling no task
motorization is not in tracking mode
motorization is not in spiral mode
vertical encoder/motor error
horizontal encoder/motor error
horizontal and vertical encoder/motor error
Description
Loading process already opened
Transfer not opened
Unknown character set
Display module not present
Character set already exists
Character set cannot be deleted
198