Leica TPS1200 Series Reference Manual page 197

GeoCOM Reference Manual
GRC_ATA_HZ_STRANGE_L
GRC_ATA_V_STRANGE_L
GRC_ATA_SLDR_TRANSFER_PENDING
GRC_ATA_SLDR_TRANSFER_ILLEGAL
GRC_ATA_SLDR_DATA_ERROR
GRC_ATA_SLDR_CHK_SUM_ERROR
GRC_ATA_SLDR_ADDRESS_ERROR
GRC_ATA_SLDR_INV_LOADFILE
GRC_ATA_SLDR_UNSUPPORTED
GRC_ATA_PS_NOT_READY
GRC_ATA_ATR_SYSTEM_ERR
EDM
RetCodeName
GRC_EDM_SYSTEM_ERR
GRC_EDM_INVALID_COMMAND
GRC_EDM_BOOM_ERR
GRC_EDM_SIGN_LOW_ERR
GRC_EDM_DIL_ERR
GRC_EDM_SIGN_HIGH_ERR
GRC_EDM_TIMEOUT
GRC_EDM_FLUKT_ERR
GRC_EDM_FMOT_ERR
GRC_EDM_DEV_NOT_INSTALLED
GRC_EDM_NOT_FOUND
GRC_EDM_ERROR_RECEIVED
GRC_EDM_MISSING_SRVPWD
GRC_EDM_INVALID_ANSWER
GRC_EDM_SEND_ERR
GRC_EDM_RECEIVE_ERR
GRC_EDM_INTERNAL_ERR
GRC_EDM_BUSY
GRC_EDM_NO_MEASACTIVITY
GRC_EDM_CHKSUM_ERR
GRC_EDM_INIT_OR_STOP_ERR
GRC_EDM_SRL_NOT_AVAILABLE
GRC_EDM_MEAS_ABORTED
GRC_EDM_SLDR_TRANSFER_PENDING
GRC_EDM_SLDR_TRANSFER_ILLEGAL
GRC_EDM_SLDR_DATA_ERROR
GRC_EDM_SLDR_CHK_SUM_ERROR
GRC_EDM_SLDR_ADDR_ERROR
GRC_EDM_SLDR_INV_LOADFILE
Leica TPS1200 – Version 1.50
529 0x211
530 0x212
531 0x213
532 0x214
533 0x215
534 0x216
535 0x217
536 0x218
537 0x219
538 0x21A
539 0x21B
768 0x300
Value HexVal
769 0x301
770 0x302
771 0x303
772 0x304
773 0x305
774 0x306
775 0x307
776 0x308
777 0x309
778 0x30A
779 0x30B
780 0x30C
781 0x30D
782 0x30E
783 0x30F
784 0x310
785 0x311
786 0x312
787 0x313
788 0x314
789 0x315
790 0x316
791 0x317
798 0x31E
799 0x31F
800 0x320
801 0x321
802 0x322
803 0x323
Return-Code names and return-code values
Strange light in Hz-direction.
Strange light in V-direction.
On multiple ATA_SLDR_OpenTransfer.
No ATA_SLDR_OpenTransfer happened.
Unexpected data format received.
Checksum error in transmitted data.
Address out of valid range.
Firmware file has invalid format.
Current (loaded) firmware doesn't support
upload.
PS-System is not ready.
ATR system error
Description
Fatal EDM sensor error. See for the exact
reason the original EDM sensor error number.
In the most cases a service problem.
Invalid command or unknown command, see
command syntax.
Boomerang error.
Received signal to low, prism to far away, or
natural barrier, bad environment, etc.
obsolete
Received signal to strong, prism to near,
stranger light effect.
Timeout, measuring time exceeded (signal too
weak, beam interrupted,..)
to much turbulences or distractions
filter motor defective
Device like EGL, DL is not installed.
Search result invalid. For the exact explanation,
see in the description of the called function.
Communication ok, but an error reported from
the EDM sensor.
No service password is set.
Communication ok, but an unexpected answer
received.
Data send error, sending buffer is full.
Data receive error, like parity buffer overflow.
Internal EDM subsystem error.
Sensor is working already, abort current
measuring first.
No measurement activity started.
Calculated checksum, resp. received data
wrong (only in binary communication mode
possible).
During start up or shut down phase an error
occured. It is saved in the DEL buffer.
Red laser not available on this sensor HW.
Measurement will be aborted (will be used for
the laser security)
Multiple OpenTransfer calls.
No open transfer happened.
Unexpected data format received.
Checksum error in transmitted data.
Address out of valid range.
Firmware file has invalid format.
197