YOKOGAWA WT200 User Manual page 149

13.1 Commands
RO/RO? Sets the recall function ON/OFF or
inquires about the current setting.
Syntax RO m<terminator>
"m" indicates recall ON or OFF.
m= 0: recall OFF
1: recall ON
Query RO?<terminator>
Example RO1
Description Parameter error 12 will occur if "m" is set to an
illegal value.
RR/RR? Sets the recall interval or queries the
current setting.
Syntax RR m1,m2,m3<terminator>
"m1" indicates the hour
0 ≤ m1 ≤ 99
"m2" indicates the minutes
0 ≤ m2 ≤ 59
"m3" indicates the seconds
0 ≤ m3 ≤ 59
Query RR?<terminator>
Example RR0,0,0
Description • Parameter error 12 will occur if an illegal value
is set.
• When the recall interval is set to 0 hrs, 0 min, 0
sec, the interval will be 250 msec during normal
measurement and 1s during harmonic analysis.
• While recalling or storing is in progress,
execution error 19 will occur.
RT/RT? Sets the rated integration time when
integrated values are to be output as an
analog signal or queries the current setting.
Syntax RT m1,m2,m3<terminator>
"m1" indicates hour, and must be set
within the following range.
0 ≤ m1 ≤ 10000
"m2" indicates minute, and must be set
within the following range.
0 ≤ m2 ≤ 59
"m3" indicates second, and must be set
within the following range.
0 ≤ m3 ≤ 59
Query RT?<terminator>
Example RT1,0,0
Description • Parameter error 12 will occur if an illegal value
is set.
• The maximum selectable time is 10000 (hours).
RV/RV? Sets voltage range or queries the
current setting.
Syntax RV m<terminator>
"m" indicates voltage range.
m= 3: 15V range
4: 30 V range
5: 60 V range
7: 150 V range
8: 300 V range
9: 600 V range
13-10
Query RV?<terminator>
Example RV9
Description • Parameter error 12 will occur if an illegal value
is set.
• Changing of the voltage range is not allowed
while integration is in progress; execution
error 13 will occur.
• While recalling or storing is in progress,
execution error 19 will occur.
SA/SA? Sets the external sensor scaling
constant or queries the current setting.
Syntax When CM0 is set:
SA n<terminator>
When CM1 is set:
SA m,n<terminator>
"m" indicates element.
m= 1: Element 1
"n" indicates external sensor scaling
constant.
0.001 ≤ n ≤ 9999.
Query When CM0 is set:
SA?<terminator>
When CM1 is set:
SAm?<terminator>
Example When CM0 is set:
SA50.00
When CM1 is set:
SA1,50.00
Description • Parameter error 12 will occur if "m" is set to an
illegal value.
• While recalling or storing is in progress,
execution error 19 will occur.
SC/SC? Determines whether or not to use the
scaling function or queries the current
setting.
Syntax SC m<terminator>
"m" indicates whether scaling is ON or
OFF.
m= 0: OFF
1: ON
Query SC?<terminator>
Example SC1
Description • Parameter error 12 will occur if "m" is set to an
illegal value.
• While recalling or storing is in progress,
execution error 19 will occur.
SL Recalls setting parameters from a
selected file.
Syntax SL m<terminator>
"m" indicates file no., and must be set
within the following range.
1 ≤ m ≤ 4
Description • Parameter error 12 will occur if "m" is set to an
illegal value.
• It is not possible to recall communications-
related information (communication mode,
address etc.) using this command.
• While recalling or storing is in progress,
execution error 19 will occur.
IM 253421-01E