Table of Contents
Advertisement
8.1 TransForm A not booting
When T
F
A is not booting properly it is important to state at which point of the boot process a fault oc-
RANS
ORM
curs. The display while booting is as follows, so you can see where the process is stopped.
On the first display (board 1/port 0, see section
tor:
M3 PCI 128b
DDCinfo: Native DFC resolution is 1024x768@68Hz
ARGUS AGX-3000
VGA BIOS-3000-04
PCX-3000[0] -> MIPS RAM Base: $F000000 -> Number of VGAs: 0
PCX-3000[1] -> MIPS RAM Base: $E600000 -> Number of VGAs: 6 (PGA inside)
Total amount of VGAs: 6
Scan system for AGX-3000
Dev BP Bus Slot
=== == === ====
0
1
3
0
init...
1
1
3
1
init...
2
1
8
0
init...
3
1
8
1
init...
4
1
11
0
init...
5
1
11
1
init...
The ordinary self test report of a PC is displayed.
The other displays show their respective bus and slot no., e. g.:
M3 PCI 128b
ARGUS AGX-3000
VGA BIOS-3000-04
Dev:
1,
BP:
1,
DDCinfo: Native DFP resolution is 1024x768@68Hz
fault
boot process is aborted while
Dev BP Bus Slot
=== == === ====
0
1
3
0
init...
/$0000B401/$48640000
1
1
3
1
init...
/$0000B401/$48644000
etc. is displayed.
boot process is aborted
CMOS checksum error
appears on the display
boot process is aborted,
This PC has no hard disk or hard disk is
unreadable. SYSTEM HALTED
appears on the display
boot process is aborted,
Unable to read system configuration Press
<F1> to resume or <F2> for setup.
appears on the display
Barco – TransForm A - X Terminal – DOC-3265-2 – user's manual – Revision 09 – September-2006
06.08.02
COPYRIGHT © 2002 BARCO Control Rooms
BAs: $1C000008/$0000B401/$48640000
BAs: $20000008/$0000B401/$48644000
BAs: $2C000008/$0000B401/$48720000
BAs: $30000008/$0000B401/$48724000
BAs: $38000008/$0000B401/$48C40000
BAs: $3C000008/$0000B401/$48C44000
06.08.02
COPYRIGHT © 2002 BARCO Control Rooms
PCI Bus: 3, Slot: 1
BAs: $20000008/$0000B401/$48644000
BAs: $1C000008
done
PGA
BAs: $20000008
done
3.2.5 Graphic
cards), respectively on the central unit's VGA moni-
done
done
done
done
done
done
cause/steps
There is probably a problem with the graphic cards. Ask
an authorized person to make sure that all graphic
cards are inserted correctly.
If the fault remains, contact Barco, please.
The battery is empty. Ask an authorized person to re-
place it by a fresh one.
Check the removable frame of the hard disk drive, if it
is inserted properly and locked. If the error message
remains after restarting T
please.
In some Processor configurations with the P
the BIOS has problems to allocate system
AGS-3390
resources during BIOS initialization. Usually this does
not impair normal system operation. Press <F1> or
disable the option "Halt on all errors" in the BIOS setup.
8. Troubleshooting
PGA
F
A, contact Barco,
RANS
ORM
ROCESSOR
______________________________________________________
Table 8-1
8-2
Advertisement
Table of Contents
