Current Probes And Sensors - AEMC PowerPad III 8336 User Manual

9.2.7 CURRENT PROBES AND SENSORS

When installing probes, face the arrow on the probe in the direction of the load. Note that only AmpFlex
watertight; all other probes and sensors are non-watertight.
Nominal Range
Measurement Range
Probe Output Signal
Maximum Clamping Ø
Safety
NOTE: Currents <0.5A will be displayed as zero. Neutral current measures down to 0A.
Nominal Range
Measurement Range
Probe Output Signal
Maximum Clamping Ø
Safety
NOTE: Currents <0.5A will be displayed as zero. Neutral current measures down to 0A.
Nominal Range
Measurement Range
Probe Output Signal
Maximum Clamping Ø
Safety
NOTE: Currents <1A
AC/DC
Nominal Range
Measurement Range
Probe Output Signal
Maximum Clamping Ø
Safety
The 5A range of the MN193 is designed to work with secondary current transformers.
Best accuracy is available when entering the transformer ratio (e.g. 1000/5A). When used to measure 5A direct, the
resolution will be limited to 0.1A max.
NOTE: Currents < (Primary x 5) ÷ (Secondary x 1000) or <250mA on the 5A range and <0.2A on the 100A range will be
displayed as zero with this probe. Power calculations will also be zeroed when the current is zeroed.
Nominal Range
Measurement Range
Probe Output Signal*
Sensor
Safety
*Output is proportional to the amplitude and frequency of the measured current.
NOTE: Currents <10A will be displayed as zero. Neutral current measures down to 0A (if 6500A or 10kA is selected)
Currents <100mA will be displayed as zero. Neutral current measures down to 0A (if 100A is selected)
128
1000A for f ≤1kHz
AC
1A to 1200A max (I >1000A not continuously)
AC
1mV /A
AC AC
2" (52mm)
EN 61010-2-032, Pollution Degree 2, 600V CAT IV, 1000V CAT III
for f ≤1kHz
200A
AC
2A to 240A max (I >200A not permanent)
AC
5mV /A
AC AC
0.8" (20mm)
EN 61010-2-032, Pollution Degree 2, 300V CAT IV, 600V CAT III
1000A , 1400A max
AC DC
10A to 1000A , 10A to 1300A
AC
1mV/A
One 1.6" (42mm) or two 0.98" (25.4mm) or
two bus bars 1.96 x 0.19" (50 x 5mm)
EN 61010-2-032, Pollution Degree 2, 300V CAT IV, 600V CAT III
will be displayed as zero. Neutral current measures down to 0A.
5A and 100A
AC
5A: 0.005A to 6A max (1A to 1200A with ratio 1000/5 selected)
AC
100A: 0.1A to 120A max
AC
5A: 200mV/A ; 100A: 10mV/A
AC
0.8" (20mm)
EN 61010-2-032, Pollution Degree 2, 300V CAT IV, 600V CAT III
3000A
AC
100mA to 10kA
140mV /3000A at 60Hz (117.3mV
AC AC
Length = 24" (610mm); Ø = 7.64" (190mm)
Length = 36" (910mm); Ø = 11.46" (290mm)
EN 61010-2-032, Pollution Degree 2, 600V CAT IV, 1000V CAT III
Model SR193
Model MN93
Model MR193
PEAK AC+DC
Model MN193
AC
AmpFlex Sensors
®
/3000A at 50Hz)
AC AC
sensors are
®
Power Quality Analyzer PowerPad III Model 8336
®