HP HSR6800 Configuration Manual page 364

CE 1
CE 2
UPE 1
SPE 1
Configuration procedure
1. Configure UPE 1:
# Configure basic MPLS and MPLS LDP to establish LDP LSPs.
<UPE1> system-view
[UPE1] interface loopback 0
[UPE1-LoopBack0] ip address 1.1.1.9 32
[UPE1-LoopBack0] quit
[UPE1] mpls lsr-id 1.1.1.9
[UPE1] mpls
[UPE1-mpls] quit
[UPE1] mpls ldp
[UPE1-mpls-ldp] quit
[UPE1] interface gigabitethernet 2/1/3
[UPE1-GigabitEthernet2/1/3] ip address 172.1.1.1 24
[UPE1-GigabitEthernet2/1/3] mpls
[UPE1-GigabitEthernet2/1/3] mpls ldp
[UPE1-GigabitEthernet2/1/3] quit
# Configure the IGP protocol, OSPF, for example.
[UPE1] ospf
[UPE1-ospf-1] area 0
[UPE1-ospf-1-area-0.0.0.0] network 172.1.1.0 0.0.0.255
[UPE1-ospf-1-area-0.0.0.0] network 1.1.1.9 0.0.0.0
[UPE1-ospf-1-area-0.0.0.0] quit
[UPE1-ospf-1] quit
# Configure VPN instances vpn1 and vpn2, allowing CE 1 and CE 2 to access UPE 1.
[UPE1] ip vpn-instance vpn1
[UPE1-vpn-instance-vpn1] route-distinguisher 100:1
[UPE1-vpn-instance-vpn1] vpn-target 100:1 both
[UPE1-vpn-instance-vpn1] quit
[UPE1] ip vpn-instance vpn2
[UPE1-vpn-instance-vpn2] route-distinguisher 100:2
[UPE1-vpn-instance-vpn2] vpn-target 100:2 both
[UPE1-vpn-instance-vpn2] quit
[UPE1] interface gigabitethernet 2/1/1
[UPE1-GigabitEthernet2/1/1] ip binding vpn-instance vpn1
[UPE1-GigabitEthernet2/1/1] ip address 10.2.1.2 24
[UPE1-GigabitEthernet2/1/1] quit
GE2/1/1 10.2.1.1/24
GE2/1/1 10.4.1.1/24
Loop0 1.1.1.9/32
GE2/1/1 10.2.1.2/24
GE2/1/2 10.4.1.2/24
GE2/1/3 172.1.1.1/24
Loop0 2.2.2.9/32
GE2/1/1 172.1.1.2/24
GE2/1/2 180.1.1.1/24
CE 3 GE2/1/1
CE 4 GE2/1/1
UPE 2 Loop0
GE2/1/1
GE2/1/2
GE2/1/3
SPE 2 Loop0
GE2/1/1
GE2/1/2
356
10.1.1.1/24
10.3.1.1/24
4.4.4.9/32
172.2.1.1/24
10.1.1.2/24
10.3.1.2/24
3.3.3.9/32
180.1.1.2/24
172.2.1.2/24