HP HSR6800 Configuration Manual page 241

[ASBR1] mpls lsr-id 2.2.2.2
[ASBR1] mpls
[ASBR1–mpls] quit
[ASBR1] mpls ldp
[ASBR1–mpls-ldp] quit
# Create remote LDP peers.
[ASBR1] mpls ldp remote-peer 1
[ASBR1-mpls-ldp-remote-1] remote-ip 3.3.3.3
[ASBR1-mpls-ldp-remote-1] quit
[ASBR1] mpls ldp remote-peer 2
[ASBR1-mpls-ldp-remote-2] remote-ip 1.1.1.1
[ASBR1-mpls-ldp-remote-2] quit
# Configure OSPF.
[ASBR1] ospf
[ASBR1-ospf-1] area 0
[ASBR1-ospf-1-area-0.0.0.0] network 2.2.2.2 0.0.0.0
[ASBR1-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255
[ASBR1-ospf-1-area-0.0.0.0] quit
[ASBR1-ospf-1] quit
# Configure basic MPLS for GigabitEthernet 2/1/1, the interface connected to PE 1.
[ASBR1] interface gigabitethernet 2/1/1
[ASBR1-GigabitEthernet2/1/1] ip address 10.1.1.2 24
[ASBR1-GigabitEthernet2/1/1] mpls
[ASBR1-GigabitEthernet2/1/1] mpls ldp
[ASBR1-GigabitEthernet2/1/1] quit
# Configure basic MPLS for GigabitEthernet 2/1/2, the interface connected to ASBR 2.
[ASBR1] interface gigabitethernet 2/1/2
[ASBR1-GigabitEthernet2/1/2] ip address 11.1.1.2 24
[ASBR1-GigabitEthernet2/1/2] mpls
[ASBR1-GigabitEthernet2/1/2] quit
# Enable L2VPN and MPLS L2VPN.
[ASBR1] l2vpn
[ASBR1-l2vpn] mpls l2vpn
[ASBR1-l2vpn] quit
# Configure a P2P-capable VPLS instance aaa that uses LDP signaling.
[ASBR1] vsi aaa static p2p
[ASBR1-vsi-aaa] pwsignal ldp
[ASBR1-vsi-aaa-ldp] vsi-id 500
[ASBR1-vsi-aaa-ldp] peer 1.1.1.1 upe
[ASBR1-vsi-aaa-ldp-1.1.1.1] quit
[ASBR1-vsi-aaa-ldp] peer 3.3.3.3
[ASBR1-vsi-aaa-ldp-3.3.3.3] quit
[ASBR1-vsi-aaa-ldp] quit
[ASBR1-vsi-aaa] quit
# Configure BGP to advertise labeled unicast routes.
[ASBR1] bgp 100
[ASBR1-bgp] import-route direct
[ASBR1-bgp] peer 11.1.1.3 as-number 200
233