HP HSR6800 Configuration Manual page 326

------------------------------------------------------------------
A '*' before an LSP means the LSP is not established
A '*' before a Label means the USCB or DSCB is stale
3. Configure VPN instances on the spoke-PEs and the hub-PE to allow CEs to access the PEs:
# Configure Spoke-PE 1.
[Spoke-PE1] ip vpn-instance vpn1
[Spoke-PE1-vpn-instance-vpn1] route-distinguisher 100:1
[Spoke-PE1-vpn-instance-vpn1] vpn-target 111:1 import-extcommunity
[Spoke-PE1-vpn-instance-vpn1] vpn-target 222:2 export-extcommunity
[Spoke-PE1-vpn-instance-vpn1] quit
[Spoke-PE1] interface gigabitethernet 2/1/1
[Spoke-PE1-GigabitEthernet2/1/1] ip binding vpn-instance vpn1
[Spoke-PE1-GigabitEthernet2/1/1] ip address 10.1.1.2 24
[Spoke-PE1-GigabitEthernet2/1/1] quit
# Configure Spoke-PE 2.
[Spoke-PE2] ip vpn-instance vpn1
[Spoke-PE2-vpn-instance-vpn1] route-distinguisher 100:2
[Spoke-PE2-vpn-instance-vpn1] vpn-target 111:1 import-extcommunity
[Spoke-PE2-vpn-instance-vpn1] vpn-target 222:2 export-extcommunity
[Spoke-PE2-vpn-instance-vpn1] quit
[Spoke-PE2] interface gigabitethernet 2/1/1
[Spoke-PE2-GigabitEthernet2/1/1] ip binding vpn-instance vpn1
[Spoke-PE2-GigabitEthernet2/1/1] ip address 10.2.1.2 24
[Spoke-PE2-GigabitEthernet2/1/1] quit
# Configure the Hub-PE.
[Hub-PE] ip vpn-instance vpn1-in
[Hub-PE-vpn-instance-vpn1-in] route-distinguisher 100:3
[Hub-PE-vpn-instance-vpn1-in] vpn-target 222:2 import-extcommunity
[Hub-PE-vpn-instance-vpn1-in] quit
[Hub-PE] ip vpn-instance vpn1-out
[Hub-PE-vpn-instance-vpn1-out] route-distinguisher 100:4
[Hub-PE-vpn-instance-vpn1-out] vpn-target 111:1 export-extcommunity
[Hub-PE-vpn-instance-vpn1-out] quit
[Hub-PE] interface gigabitethernet 2/1/1
[Hub-PE-GigabitEthernet2/1/1] ip binding vpn-instance vpn1-in
[Hub-PE-GigabitEthernet2/1/1] ip address 10.3.1.2 24
[Hub-PE-GigabitEthernet2/1/1] quit
[Hub-PE] interface gigabitethernet 2/1/2
[Hub-PE-GigabitEthernet2/1/2] ip binding vpn-instance vpn1-out
[Hub-PE-GigabitEthernet2/1/2] ip address 10.4.1.2 24
[Hub-PE-GigabitEthernet2/1/2] quit
# Configure IP addresses for the CEs according to
After the configurations, execute the display ip vpn-instance command on the PEs to view the
VPN instance configurations. Use the ping command to test connectivity between the PEs and
their attached CEs. The PEs can ping their attached CEs.
Take Spoke-PE 1 as an example:
[Spoke-PE1] display ip vpn-instance
Total VPN-Instances configured : 1
Figure 89. (Details not shown.)
318