Advertisement
&RPSDWLEOH ' 6RXUFHV
*ODVVHV 6SHHG
9HUW 5DWH
FORVHG —V
+]
FORVHG —V
+]
FORVHG —V
+]
FORVHG —V
+]
FORVHG LQ —V
+]
' 7URXEOHVKRRWLQJ
NOTES: 1) Increasing the Dark Interval decreases the peak brightness of the image.
Use only if necessary—you may prefer some color artifacts rather than reduced
brightness, or vice versa. 2) Higher input frame rates limit the range of Dark Interval
adjustment. 3) You may have to adjust Gamma (if available—it is set to "Default" if
the Adjust Primary Colors function is also in use) to account for the longer dark
interval. 4) Faster glasses enable use of a briefer dark interval.
93RVLWLRQ DQG 6\QFKURQL]DWLRQ
By default, the projector begins display on its first (top) line of pixels. However, it is
important to remember that a V-Position adjustment (accessed in the Size and
Position menu) determines the first active line in the source, moving your display
accordingly. Such an adjustment, therefore, increases or decreases the delay in your
display signal, in turn changing the required synchronization in your 3D application.
N
,) 9326,7,21 ,6 +,*+
N
,) 9326,7,21 ,6 /2:
Note that H-Position and Blanking controls do not affect timing parameters.
The following sources are optimized for active 3D images using the projector and
active glasses. Clamp Tip is "off". The first signal in the table is 1024 x 1024 and all
others are 1280 x 1024.
7DEOH &RPSDWLEOH ' 6RXUFHV
+RUL]RQWDO 7LPLQJ 3DUDPHWHUV 3L[HOV
3L[HO 5DWH
)URQW 3RUFK
(
0+]
0+]
0+]
0+]
0+]
(
1024 x 1024. All others shown are 1280 x 1024.
Refer to the following guide when 3D images displayed by your projector do not
appear as you expect:
)/,&.(5,1* ,0$*(
,0$*( ,6 &2035(66(' +25,=217$//<
already maximized, the pixel clock rate of the source is too high for the projector.
&$1·7 6(/(&7 ´0,1,080 '(/$<µ
have an appropriate signal connected. Check your source—make sure it meets the
criteria listed earlier in 3D Source Requirements and Conditions.
' &52667$/. *+267,1*
signals can reach glasses. 2) If using a Pi Cell polarizer and passive glasses, make sure
you are using a screen that maintains polarity. 3) Are depleted batteries slowing down the
active glasses? 4) Fix timing parameters in your source. 5) Adjust Dark Interval setting.
12 ,0$*( -803< ,0$*( 25 12,6( $7 ,0$*( 723
timings for blanking and pulsed width are too slow for use with the projector.
:,7+287 */$66(6 , 6(( 21/< $ 6,1*/( ,0$*(
sure "Minimum Delay" processing mode is selected in the Advanced Image Settings
menu.
¨ ¨
More delay, so display starts later in the signal
¨ ¨
Less delay, so display starts earlier in the signal
6\QF :LGWK
%DFN 3RUFK
: Make sure your source signal is 96 Hz or higher.
: If this option is disabled (gray), you likely do not
: 1) Make sure the IR emitter is not blocked and that its
9HUWLFDO 7LPLQJ 3DUDPHWHUV /LQHV
)URQW 3RUFK
6\QF :LGWK
: Increase pixel tracking to 1424 or higher. If
: Your video card's minimum
: You are not in 3D mode. Make
0LUDJH
23(5$7,21
%DFN 3RUFK
8VHU·V 0DQXDO
Advertisement
