Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
For complete Mirage SST product documentation and technical support, go to www.christiedigital.com. Third-party products This projector is certified to work only with certain specified third-party components. Use only Christie approved third-party components with the projector. Using non-approved components with the projector can lead to potential safety hazards and void the projector warranty.
Possible hazardous optical radiation emitted from this product. (Risk group 3) • Only Christie qualified technicians who are knowledgeable about the hazards associated with laser use, high-voltage, and high temperatures generated by the product are authorized to assemble, install, and service the Christie Laser Projection System.
Certain US states have additional laser regulatory requirements. Contact lasercompliance@christiedigital.com for additional regulatory requirements. Product documentation For installation, setup, and user information, see the product documentation available on the Christie website. Read all instructions before using or servicing this product. 1. Access the documentation from the Christie website: •...
Contact your dealer Record the information about your projector and keep this information with your records to assist with the servicing of your projector. If you encounter a problem with your Christie projector, contact your dealer. Purchase record...
Adjusting the image Adjust the projector image. Christie recommends warming the lens before completing these procedures as focus may change as the lens warms. Selecting screen image orientation Specify the orientation to use for the image. The projector supports front projection, rear projection, front projection inverted, or rear projection inverted.
• Show All Warnings—Shows all lens warnings. • Hide Zoom Motor Warnings—Hides zoom motor warnings. Christie recommends selecting this option when using a fixed lens as all zoom operations are disabled. • Hide Detection Warnings—Hides lens detection warnings. Christie recommends selecting this option when using a third-party lens.
Signal color correction Adjust the video signal color as required. For best results, Christie recommends setting all color and gamma settings to Auto Detect. Adjusting the color space Determine how the color components are decoded for accurate color in the display.
1. Create an edge blend file using the or application. To connect Mirage SST with or , use port 3003. Christie Twist Premium, Twist Pro, and offer advanced warping options. Refer to the Christie website (www.christiedigital.com) for product information and documentation.
1. Create a warp file using the or application. To connect Mirage SST with or , use port 3003. Christie Twist Premium, Twist Pro, and offer advanced warping options. Refer to the Christie website (www.christiedigital.com) for product information and documentation.
Mirage Pro license Additional components • Christie Twist 2.5 Video sources Three video sources and Christie Link are supported for Christie high frame rate. • All sources must be frame synchronous. • 1920 x 1080 (FHD) image formats are supported.
Issuing the (OTR <0 | 1>) serial command for the Griffyn Series and Mirage SST also toggles between the 4K and 2K resolutions. Selecting the high frame rate EDID Configure the projector and/or Christie Link for the 3D source. 1. From the projector: a) Select MENU > Configuration > Input Settings > EDID Timing.
1. Ensure the projector is running in representative ambient light. 2. Setup a spectroradiometer, such as the CR-250, on a tripod. If not using the CR-250 or better, Christie recommends placing the meter perpendicular to the screen to achieve accurate measurements.
Not all options listed in the table are available on all products. Available options depend on the projector model and the cards installed on the projector. The QSFP+ options require the Enable Christie Link option to be set.
Setting up Christie View Christie View allows up to four different video sources to be displayed on one screen at the same time. The system displays up to four inputs from a single projector simultaneously, which enables multiple viewers to observe up to four different experiences.
1. Set up the projector and connect to AC power. Do not turn on the projector. 2. Plug the content source outputs into the projector. 3. Connect the female DB9 end of the Christie View cable into the male GPIO connector on the projector. Mirage SST User Guide 020-102993-06 Rev.
If using the XPAND Vision glasses for the first time, they must be paired with the RF emitter(s). If the glasses have already been paired, skip to step 7. 1. Connect the first RF emitter to the mini-DIN3 connector on the Christie View cable labeled A. Ensure only one emitter is connected to the Christie View cable.
To turn off the XPAND Vision glasses, press the button on the inside of the frame. A red light flashes once, slowly. Connection diagrams The following diagrams illustrate some of the connection possibilities for Christie View. Frame-locked content sources are required. Four-port, 4-Viewer 2D (1080p 60 Hz connection) Mirage SST User Guide 020-102993-06 Rev.
Solution: 1. Make sure the projector is in Christie View mode. 2. Make sure the Christie View cable is seated correctly on the projector and the RF emitter(s) are seated correctly for each mini-DIN3 connector on the cable. Image tear appearing on the screen The screen shows a different frame of video than what is shown on the bottom portion of the screen.
Page 60
Solution: 1. Make sure the projector is in Christie View mode. 2. Make sure the Christie View cable is seated correctly on the projector and the RF emitter(s) are seated correctly for each Mini-DIN3 connector on the cable. 3. The glasses may need to be paired again with an RF emitter.
Configuration menu, or you can send the (SST+CONF?1) serial API command. Christie Technical Support will send a zipped license file to you. If you sent more than one serial number, you will receive multiple license files as the .key file is based on the serial number of the projector.
2. Scroll to the status category you want to view and select it. Running the Mirage SST interrogator The interrogator captures diagnostic information Christie personnel uses to help diagnose and correct any issues. 1. If saving the interrogator file to a USB flash drive on the projector, insert a USB flash drive in the USB port on Mirage SST.