Mitsubishi Electric MELSEC iQ-R Series User Manual page 195

Address: CH Setting details
Decimal
Standard
(hexadeci
control
mal)
60(3CH) CH1 Loop
disconnection
detection dead
band
61(3DH) CH1 Unused channel setting
62(3EH) CH1 Memory's PID constants read command
63(3FH) CH1 Automatic backup setting after auto tuning of PID constants
64(40H) CH2 Input range
65(41H) CH2 Stop mode setting
66(42H) CH2 Set value (SV) setting
67(43H) CH2 Proportional
band (P) setting
68(44H) CH2 Integral time (I) setting
69(45H) CH2 Derivative time (D) setting
70(46H) CH2 Alert set value 1
71(47H) CH2 Alert set value 2
72(48H) CH2 Alert set value 3
73(49H) CH2 Alert set value 4
74(4AH) CH2 Upper limit
output limiter
75(4BH) CH2 Lower limit
output limiter
76(4CH) CH2 Output variation amount limiter
77(4DH) CH2 Sensor correction value setting
78(4EH) CH2 Adjustment sensitivity (dead band)
setting
79(4FH) CH2 Control output
cycle setting
80(50H) CH2 Primary delay digital filter setting
81(51H) CH2 Control response parameter
82(52H) CH2 AUTO/MAN mode shift
83(53H) CH2 MAN output setting
84(54H) CH2 Setting variation rate limiter/setting
variation rate limiter (temperature
*10
rise)
85(55H) CH2 AT bias
Heating- Mix control
cooling
control
System area
Stop mode
*3
setting
Set value (SV)
*3
setting
Heating Heating
proportional proportional
band (Ph) setting band (Ph)
*3
setting
Integral time (I)
*3
setting
Derivative time
*3
(D) setting
Alert set value
*3
1
Alert set value
*3
2
Alert set value
*3
3
Alert set value
*3
4
Heating upper Heating upper
limit output limit output
*3
limiter limiter
System area
Output variation
*3
amount limiter
Adjustment
sensitivity (dead
*3
band) setting
Heating control Heating control
output cycle output cycle
*3
setting setting
Control
response
*3
parameter
AUTO/MAN
*3
mode shift
MAN output
*3
setting
Setting variation
rate limiter/
setting variation
rate limiter
(temperature
*3*10
rise)
*3
AT bias
Default Data
value type
Position-
proportional
control
0 Setting
0 Setting
0 Setting
0 Setting
2(TCTRT) Setting
7(TCRT)
Stop mode 1 Setting
setting
Set value (SV) 0 Setting
setting
Proportional 30 Setting
band (P) setting
Integral time (I) 240 Setting
setting
Derivative time 60 Setting
(D) setting
Alert set value 1 0 Setting
Alert set value 2 0 Setting
Alert set value 3 0 Setting
Alert set value 4 0 Setting
System area 1000 Setting
0 Setting
System area 0 Setting
0 Setting
Adjustment 5 Setting
sensitivity (dead
band) setting
*15
System area 30 Setting
*16
300
0 Setting
Control 0 Setting
response
parameter
System area 0 Setting
System area 0 Setting
Setting variation 0 Setting
rate limiter/
setting variation
rate limiter
(temperature
*10
rise)
AT bias 0 Setting
Appendix 3 Buffer Memory Areas
(1) (2) (3) (4) (5)
    
    
    
    
    
    
    
    
    
    
    
    
    
A
    
    
    
    
    
    
    
    
    
    
    
    
    
APPX
193