Index - YASKAWA A1000 HHP Programming Manual

Numerics
2-Wire Initialization .........................................................11
3-Wire Initialization .........................................................11
3-Wire Sequence.............................................................11
3-Wire Sequence Wiring Diagram ........................................96
5th Most Recent Fault..................................................... 302
A
A/D Conversion Error..................................................... 185
A1-02 (Motor 1 Control Mode) Dependent Parameters .............. 307
A1-04 ........................................................................ 227
A1-04, A1-05: Password and Password Setting .........................11
A1-05 ........................................................................ 227
Abnormal Diode Module Fan ...................................... 187, 205
Abnormal Panel Fan................................................. 187, 205
Accel/Decel Time.......................................................... 177
Accel/Decel Time Setting Units ...........................................48
Accel/Decel Time Switching Frequency .................................47
Acceleration Error ......................................................... 219
Acceleration Time ...........................................................46
Access Level Selection......................................................10
Action Selection below Minimum Output Frequency ..................22
Adjusted Slip Calculation Error ......................................... 217
Adjusting the ASR Parameters.............................................53
AEr........................................................................... 203
AFR Gain ................................................................... 176
AFR Time Constant 1 ..................................................... 176
AFR Time Constant 2 ..................................................... 177
AI-A3 Settings ...............................................................86
Alarm Register 007FH Contents......................................... 343
Alarms and Errors ......................................................... 179
Ambient Temperature Setting...................................... 155, 288
Analog Filter Time Constant ............................................. 177
Analog Frequency Reference Fluctuation Limit.........................67
Analog Frequency Reference Sample/Hold............................ 101
Analog Input Card Settings.................................................86
Analog Input Filter Time Constant ...................................... 117
Analog Input Option Card Bias ............................................87
Analog Input Option Card Gain ...........................................87
Analog Input Option Card Operation Selection .........................86
Analog Input Terminal Enable Selection ............................... 118
Analog Monitor Card Settings .............................................88
AO-A3 Settings ..............................................................88
ASR............................................................................53
ASR Gain Switching Frequency...........................................55
ASR Integral Limit ..........................................................56
ASR Integral Time...........................................................54
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual
ASR Limit ....................................................................56
ASR Primary Delay Time Constant .......................................56
ASR Proportional Gain .....................................................54
Automatic Reduction for Stall Prevention during Run ............... 144
Automatic Reduction Selection for Stall Prevention during Run ... 285
Automatic Speed Regulator ................................................53
Auto Restart Fault Output Operation Selection........................ 147
Auto Restart Operation Selection........................................ 286
Auto-Tuning Codes........................................................ 217
Auto-Tuning Errors........................................................ 182
Auto-Tuning Fault Detection............................................. 217
Auto-Tuning Fault Solutions ............................................. 217
Auto-Tuning Mode Selection ...................................... 168, 296
B
b1-01......................................................................... 227
b1-02......................................................................... 227
b6-01 through b6-04....................................................... 177
Baseblock ................................................................... 203
Base Frequency ..............................................................76
Base Voltage .................................................................76
bb............................................................................. 203
Bi-Directional Speed Search Selection ...................................32
boL..................................................................... 184, 203
Braking Resistor Fault .................................................... 198
Braking Resistor Overheat................................................ 198
Braking Transistor Overload Fault ................................ 184, 203
Broadcast Messages ....................................................... 340
bUS .................................................................... 184, 203
bUS Error Auto Reset .......................................................91
bUS Error Detection Time..................................................91
C
C2-01 through C2-04...................................................... 177
C3-01 .................................................................. 176, 177
C3-02 ........................................................................ 177
C4-01 ........................................................................ 176
C4-02 .................................................................. 176, 177
C4-06 ........................................................................ 177
CALL........................................................................ 204
Cannot Change Parameter Settings...................................... 226
Cannot Reset ............................................................... 204
CANopen Communication Speed .........................................92
CANopen Node ID Selection ..............................................92
CANopen Parameters .......................................................92
Capacitor Maintenance.................................................... 302
Capacitor Maintenance Setting .................................... 165, 293
Capacitor Maintenance Time............................................. 207

Index

347