Adding Custom Words - ADEMCO Vista-20 Installation Instructions Manual

4.
5.
6.
For selectionof the next word (e.g.,DOOR), repeat step 3, as follows.
Press key [3] until the fist letter of the next word appears (e.g., "D").
Then press [6] to display the first available word beginning with that
letter (e.g. DAUGHTERS). Press [3] repeatedly until the desired word
(e.g., DOOR) appears.To acceptthe word, press [6], which togglesback to
the alphabet list.
When all desired words have been entered, press [8] to store the
descriptionin memory.
Enter *NN, where NN is the next zone that You want to review or for
which you want to program a descriptor.To m~di@ the descriptor,enter
*NN again. To exit this mode, press"*oO".
Adding Cuetom Words (will not be annundated by 4285 Voice Module)
You can add up to five installer-defied words can be added to the built-in vo-
cabulary. Each of the five "words" can actually consist of a "word string" of
one or more words, but no more than ten characters can be used for each
word or word string.
[s]
[11
[6]
[4
[n
[8]
Adv=ces through the
alphabet in ascending
order.
Moves through the
alphabetin descending
order.
Selectsdesired letter;
movescursoronespace
toright.
Movescursoronespace
to left.
Inserts a spaceat the
cursorlocation, e rasing
any character located
there.
Savesthe newwordin
thesystem's memory.
1.
2.
3.
4.
5.
6.
Perform steps 1,
2, and 3
of
Programming the Descriptors
on a
previous page.
Select CUSTOM WORD mode (enter "1") when the prompt CUSTOM
WORD ? is displayed.
Enter the number ([1]–[5]) of the custom word or word string to be
created (for example, if you are creating the first custom word or word-
string, enter [1], for the
second,
enter [2], etc.).A cursor will now appear
at the beginning of the secondline.
One
of two methods of entering the custom word's characters can
now be used (refer to the CHARACTER LIST of letters, numbers, and
symbols on a followingpage):
Method 1:
Press the [#]
key, followed by the two-digit entry for the W letter you
would like to display (e.g., [6][5] for "A"),
or...
Method 2:
Use the
[3]
key to advance through the list of symbols, numbers, and
letters. Use the [1] key to move back through the list.
When you have reached the desired character, press [6] to selectit. The
cursor will then move to the right, in position for the next character.
Repeat steps 3 end 4 to create the desired word(s). Note that the [4] key
can be used to move the cursor to the left, if necessary,and that key [71
can be used to enter a blank (or erase an existing character).Remember,
no word or word-shing can exceed10 characters.
Press the [81key to savethe customword(s) and return to the "CUSTOM
WORD
?-displiy.
Repeat steps 2-5 for other custom words to be entered. To change a
customword, just overwrite it. If no more are to be entered now, press [0]
to return to the Descriptor entry. The custom word(s) will be
automatically added to the built-in vocabulary.
When zone descriptors are being entered as described in step 6 of
Programming the Descriptors, the custom word numbers are 250 to 254
for words 1 to 5 respectively.
When being entered as described in step 3 in Alternate Method For
Programmhg Zone Descriptors, eachword will be found at the end of the
group of words that begin with the sameletter as it does.
-70-