Table of Contents
Advertisement
Instalbg
5S00 Series Tranmmtt
—
"em
To be sure reception of the transmitter's signal at the proposed mounting
locationis adequate,perform a Go/No Go test.
GdNo
Go
Test
Mode
The Go/No Go testswill veri& adequateRF signal strength fkomthe proposed
transmitter location, and allow you to reorient or relocate transmitters if
necessary,beforemounting the transmitters permanently.
This mode is eimiIar to the transmitter test mode, exceptthat the wireless
receivergain is reduced.This will enableyou to make sure that the RF signal
horn each hansmitter is receivedwith su.fiicientsignal amplitude when the
systemis h the normal operatingmode.
1. With at least one 2-line Alpha keypad (5137AD or 6139) connectedto the
system, power up the system temporarily.
If you had previously
connected the AC hnsformer
to the contiol panel, you need only plug in
the transformer (to 120VAC outlet)to power up the system.
2.
Enter installer code (4112)+ # + 4. For multi-partition systems,make
sure all partitions are disarmedbeforeentering this mode.
3.
Once you have placed transmitters in their desired locations and the
approximate length of wire to be run to sensors is connected to the
transmitter's screwtermbls
(ifused), fault each transmitter.
Do not
conduct this test with your hund wrapped around the transmitter as this
will cause in.u.ccurateresults.
Not@
On button @pe transmitters whose buttons have been set to Arm
Away, Arm Stay, or Disarm, pressinga button wi.Utake the system out of
the Go/No Go Test modeend causethat action-
a. The keypad will beep three times to indicate signal reception and
display the appropriate zone number.
b. If the keypad does not beep, reorient or move the transmitter to
another location. Usuelly a few inches in either direction is all that is
eed.
4.
If each transmitter produces the proper keypad response when it is
faulted, you can then permanently mount each of the transmitters
amording to the instructionsprovided with them.
5.
Exit the Go/No Go test modeby en-
Installer code (4112)+ o~.
6
Unplug the AC transformer.
~
fh@ing DIPswEtches onthe5827T
rammdtter(s)
A 5827
lmmemitter must be set to the selected House ID, using its DIP
switches. If a 5827 is also being used in partition 2, you must set its DIP
switch to an ID that is one number higher than the one in partition 1 (e.g.,if
House ID selectedis 11, setthe 5827 in partition 1 to "11", and the 5827 in
partition 2 to "12".
SWTCH UPFOR W
m
mm
12345
HOUSE ID
SWITCH OOWN FOR VFF
SHOWN SEr
FORHOUSE iO#30
5827 Wireless Keypad DIP S
W
1
(XF [ @F
F cm
2 OFF I GF OFFIOn
3 GF CPFOFFon cm'
4
OFF *F
on
CtF
s
UT m= on
OFFiOfI
w
6
&F
O=Fon
OFF
h
7
&FcPF
on
on&
8
W&
OFFW=
9
OFF
OIOFFOFFCII
10
CPFOIIOFFOFFQI
11
CPFO!OfF
OnOn
12
CfF~On
OFF
OFF
13
CPFO1On
OFF
OfI
14
GFcnon
onOfF
witch Table
,-, .-, ,,.
..."
IQ
I
112131415
17
loll
-FltXFl
O+F
on
18
[on
CFFIOfF
IOn
m
19
on
CFFl
OFPfOn
On
20
Q!
OPF
al
OFF
C#
ul
C+F
m
OFF
On
22
*
OFF
m
on
OFF
a
-
CPF
on
on
on
24
on
al
OFF @F IOF!=
I
2E
Ion ion IOFFIOFFIGI
I
1-1–111
23
on
2s
on on on
OFF on
30
on
al
on
cm w
31
on
t%
Cm on
al
-41-
- Quick Links:
- Security Codes
- Entering Program Mode
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
