GE Interlogix Concord Security System Installation Instructions Manual page 33

Dealer Code (0002)
The 4-digit dealer code is used to prevent unauthorized per-
sons from changing the programmed central station phone
numbers. When this feature is enabled, central station phone
numbers cannot be changed (unless you enter the program
mode by using the dealer code). All other system settings are
still accessible by entering the program mode with the installer
code.
Note
The Dealer Code cannot be deleted by clearing panel memory.
Access Code Lock (0003)
This setting determines whether or not the panel will include Access
Codes when sending user information to the automation module. When
this option is on, it means the Access Codes are not sent.
Note
The Dealer Code cannot be deleted by clearing panel memory.
SIA False Alarm Reduction (0004)
Controls the following settings that are required by the SIA False Alarm Reduction Stan-
dard:
• Arming level changes made from wireless touchpads and keychain touchpads are
sounded (beeps) on exterior siren output (on) OR are not sounded on exterior siren out-
put (off).
Note
The siren output must be configured for "Exterior Siren" (016xx) and on the two onboard outputs
and SnapCard outputs only, for the arming level beeps to be annunciated.
• The Arming Always Silent feature is disabled for users if this setting is on OR can be
controlled by users if the setting is off. Silent Arming on Demand is not affected.
Account Number (partition 1: 0010, partition 2: 0020)
The account number is used as panel (or customer) identification for the cen-
tral monitoring station. The panel sends the account number every time it
reports to the central station. Account numbers must be 1 to 10 characters
long.
Alpha characters A–F can be assigned to the account number by pressing
and holding buttons 1–6 respectively, until the character appears.
Quick Arm (partition 1: 0011, partition 2: 0021)
Quick Arm allows system arming without using an access code. When
Quick Arm is on, the system arming level can be increased from Level 1-
OFF to LEVEL 2-STAY, from Level 1-OFF to LEVEL 3-AWAY, or from
Level 2-STAY to LEVEL 3-AWAY, without entering an access code.
A valid access code is still required to decrease the arming level or disarm
the system.
Concord
The following sections describe the security settings that appear under
Security-Global (Default = none)
¾
To program a Dealer Code:
1. With the display showing
desired 4-digit code. The display flashes the entered
code.
2. Press # and the display shows the new code.
¾
To delete a Dealer Code:
1. With the display showing
code), press D. The display shows
¾
To turn Access Code Lock off or on:
1. With the display showing
, press 1 (off) or 2 (on). The display
ON/OFF
flashes the entered setting.
2. Press # and the display shows the new setting.
Security-Partition 1-2 (Default = 00000)
¾
To program an Account Number:
1. With the display showing
BER nnnnn
desired account number. The display
flashes the entered number.
2. Press # and the display shows the new
number.
Security-Partition 1-2 (Default = off)
¾
To turn Quick Arm off or on:
1. With the display showing
(current setting), press 1 (off) or 2 (on).
ON
The display flashes the entered setting.
2. Press # and the display shows the new set-
ting.
, enter the
DEALER CODE ****
(current
DEALER CODE nnnn
DEALER CODE ****
Security-Global (Default = on)
ACCESS CODE LOCK
Security-Global (Default = on)
¾
To turn SIA False Alarm
Reduction off or on:
1. With the display showing
(current setting),
FALSE ALARM
press 1 (off) or 2 (on). The
display flashes the entered set-
ting.
2. Press ƒ and the display shows
the new setting.
and
PARTITION 1 2
ACCOUNT NUM-
(current number), enter the
QUICK ARM OFF/
.
SIA
.
28