Mitsubishi Electric FR-A700 Technical Manual page 133

[Pr.] Name
300 BCD input bias 0 to 400Hz
301 BCD input gain 0 to 400Hz, 9999
302 BIN input bias 0 to 400Hz
303 BIN input gain 0 to 400Hz, 9999
Digital input and analog input compensation
304 0 to 4, 10 to 14, 9999
enable/disable selection
305 Read timing operation selection 0, 1, 10
1 to 3, 5 to 14, 17, 18, 21, 24,
306 Analog output signal selection
32 to 34, 50, 52, 53
307 Setting for zero analog output 0 to 100%
308 Setting for maximum analog output 0 to 100%
Analog output signal voltage/current
309 0, 1, 10, 11
switchover
1 to 3, 5 to 14, 17, 18, 21, 24,
310 Analog meter voltage output selection
32 to 34, 50, 52, 53
Setting for zero analog meter voltage
311 0 to 100%
output
Setting for maximum analog meter voltage
312 0 to 100%
output
313 DO0 output selection
0 to 8, 10 to 20, 25 to 28, 30
314 DO1 output selection
to 36, 39, 41 to 47, 64, 70, 84
315 DO2 output selection
to 99, 100 to 108, 110 to 116,
316 DO3 output selection
120, 125 to 128, 130 to 136,
317 DO4 output selection
139, 141 to 147, 164, 170,
318 DO5 output selection
184 to 199, 9999
319 DO6 output selection
320 RA1 output selection 0 to 8, 10 to 20, 25 to 28, 30
321 RA2 output selection to 36, 39, 41 to 47, 64, 70, 84
322 RA3 output selection to 91, 94 to 99, 9999
323 AM0 0V adjustment 900 to 1100%
324 AM1 0mA adjustment 900 to 1100%
— 329 Digital input unit selection 0, 1, 2, 3
331 RS-485 communication station number 0 to 31 (0 to 247)
332 RS-485 communication speed 3, 6, 12, 24, 48, 96, 192, 384
333 RS-485 communication stop bit length 0, 1, 10, 11
RS-485 communication parity check
334 0, 1, 2
selection
335 RS-485 communication retry count 0 to 10, 9999
336 RS-485 communication check time interval 0 to 999.8s, 9999
337 RS-485 communication waiting time setting 0 to 150ms, 9999
338 Communication operation command source 0, 1
339 Communication speed command source 0, 1, 2
340 Communication startup mode selection 0, 1, 2, 10, 12
341 RS-485 communication CR/LF selection 0, 1, 2
342 Communication EEPROM write selection 0, 1
343 Communication error count —
345 DeviceNet address 0 to 4095
346 DeviceNet baud rate 0 to 4095
349 Communication reset selection 0, 1
PARAMETER
Minimum Setting Refer to
Setting Range Initial Value
Increments
0.01Hz 0Hz
0.01Hz 60Hz
0.01Hz 0Hz
0.01Hz 60Hz
1 9999 229, 301
1 0 229, 301
1 2
0.1% 0%
0.1% 100%
1 0
1 2
0.1% 0%
0.1% 100%
1 9999
1 9999
1 9999
1 9999
1 9999
1 9999
1 9999
1 0
1 1
1 2
1 1000%
1 1000%
1 1
1 0 441, 459
1 96 441, 459
1 1
1 2 441, 459
1 1
0.1s 0s
1 9999
1 0
1 0
1 0
1 1
1 0
1 0
1 63
1 132
1 0
132
[Pr.] Option
Page
229 300
229 301
229 302
229 303
304
305
345 306
357 307
357 308
357 309
345 310
357 311
357 312
61 313
61 314
61 315
61 316
61 317
61 318
61 319
61 320
61 321
61 322
357 323
357 324
229 329
331
332
441 333
334
441 335
441 336
441 337
436 338
436 339
434 340
441 341
443 342
459 343
— 345
— 346
— 349
Instruction Code Control Mode-based Correspondence Table
Advanced
Vector control
magnetic
flux
vector
control
00 80 3 ×
01 81 3 ×
×
02 82 3
×
03 83 3
×
04 84 3
05 85 3 ×
06 86 3
07 87 3
08 88 3
09 89 3
0A 8A 3
0B 8B 3
0C 8C 3
0D 8D 3
0E 8E 3
0F 8F 3
10 90 3
11 91 3
12 92 3
13 93 3
14 94 3
15 95 3
16 96 3
17 97 3
18 98 3
×
1D 9D 3
1F 9F 3
20 A0 3
21 A1 3
22 A2 3
23 A3 3
24 A4 3
25 A5 3
26 A6 3
27 A7 3
28 A8 3
29 A9 3
2A AA 3
2B AB 3
2D AD 3
2E AE 3
31 B1 3
132
PARAMETER
Real sensorless
vector control
Speed Torque
control control
2
×
×
×
*8 *8
*8 *8
*8 *8
*8 *8
*8 *8
*8 *8
*8 *8
*8 *8
*8 *8
*8 *8
*8 *8
× × ×
*8 *8
*8 *8
*8 *8