SATO HT200e Operator's Manual page 98

SECTION 5 PRESET, TABLE DATA
：
DELETION OF PRESET DATA
Ｆ Ｏ Ｒ Ｍ Ａ Ｔ Ｎ ｏ
1 ［ ・ ・ ］
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
2 Ｐ Ｒ Ｉ Ｎ Ｔ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
3 Ｐ Ｒ Ｉ Ｎ Ｔ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
4 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
5 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｎ Ｏ ． Ｉ Ｎ Ｐ Ｕ Ｔ ＊
6 ・ ・ ・ ・
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｄ Ｅ Ｌ Ｅ Ｔ Ｅ Ｏ Ｋ
7 ・ ・ － ・ ・ ・ ・
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｄ Ｅ Ｌ Ｅ Ｔ Ｅ Ｄ
8
Note: Where asterisk mark or "*" can be seen in the upper right on the screen, entry by scanner can be made
possible.
Page 5-6
Ｈ Ｔ ２ ０ ０ ｅ
[RCL]
Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
[ ]
→
Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
[ ]
→
Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
[ ]
→
[ENTR]
＜ Ｄ Ｅ Ｌ Ｅ Ｔ Ｅ ＞
[ENTR]
Ｙ ／ Ｎ
[ENTR]
Press [RCL], so that it goes from the modes of
the print to the preset.
The screen for the selection of preset printing will
be displayed: Press [
→
screen for the process No. 3.
The screen for the selection of preset storing will
be displayed: Press [ ], so that it goes to the
→
screen for the process No. 4.
The screen for the selection of preset modification
will be displayed: Press [
screen for the process No. 5.
The screen for the selection of preset deletion will
be displayed: Press [ENTR], so that it goes to the
entry of preset number.
The preset No. that is required to delete can be
entered: Press [ENTR], so that it appears the con-
firmation for deletion.
Use [ ] and [ ] to respond to the confirmation.
← →
Press [ENTR], so that it deletes the preset data
specified.
When specified preset is deleted, it will display a
message for the end of deletion and returns to the
process No. 6.
], so that it goes to the
] , so that it goes to the
→
SATO HT200e