SATO HT200e Operator's Manual page 48

SECTION 2: INSTALLATION AND SETUP
PROCESS ON THE SCREEN FOR SERVICE MAINTENANCE MODE
9 + Power "ON"
Ｔ Ｅ Ｓ Ｔ Ｐ Ｒ Ｉ Ｎ Ｔ
1
[ ]
←
Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ Ｃ Ｈ Ｅ Ｃ Ｋ
2
[ ]
←
Ｒ Ａ Ｍ Ｂ Ａ Ｃ Ｋ Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
3
[ ]
←
Ｃ Ａ Ｒ Ｄ Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
4
[ ]
←
Ｒ Ｏ Ｍ Ｖ ｅ ｒ ．
5
Press [ENTR], so that it can go to each screen for processing.
For Service Maintenance Mode, [PGUP] is invalid, whereas [FMT] is valid.
PROCESS ON THE SCREEN FOR TEST PRINT
Ｔ Ｅ Ｓ Ｔ Ｐ Ｒ Ｉ Ｎ Ｔ
1
Ｌ Ａ Ｂ Ｅ Ｌ Ｔ Ｙ Ｐ Ｅ
Ｎ Ｏ Ｒ Ｍ Ａ Ｌ
Ｌ Ａ Ｂ Ｅ Ｌ Ｓ Ｉ Ｚ Ｅ
Ｐ ［ １ ０ ３ ］
Ｔ Ｅ Ｓ Ｔ Ｐ Ｒ Ｉ Ｎ Ｔ Ｉ Ｎ Ｇ
Page 2-30
１ Ｗ ０ ０ ０ ０
9 + Power "ON"
[ENTR]
Ｏ Ｐ Ｔ Ｉ Ｏ Ｎ
[ENTR]
Ｗ ［ ４ ８
[ENTR]
Press [ENTR], so that it starts test print.
Press [ ], so that it goes to the process No. 2.
→
[ ]
→
Press [ENTR], so that it displays voltage in battery.
Press [ ], so that it returns to the process No. 1.
←
Press [ ], so that it goes to the process No. 3.
→
[ ]
→
Press [ENTR], so that battery level (or remaining
fuel) can be indicated for RAM's back-up.
Press [ ], so that it returns to the process No. 2.
←
Press [ ], so that it goes to the process No. 4.
→
[ ]
→
Press [ENTR], so that battery level (or remaining
fuel) can be indicated for card's back-up.
Press [ ], so that it returns to the process No. 3.
←
Press [ ], so that it goes to the process No. 5.
→
[ ]
→
A ROM version can be displayed:
Note that [ENTR] is not available.
Press [ ], so that it returns to the process No. 4.
←
Press [ENTR], so that it goes to the screen for the
selection of the label type in the test print.
Select label type with [
[ENTR],so that it goes to the screen for label size.
Label size can be entered with numeric keypad:
Press [ENTR], so that it starts printing.
］ ｍ ｍ
Test print will be terminated when printing one sheet
of paper is complete: Press [S/S], so that test print
can be executed as is ordered.
Ensure that whether label has been properly set prior
to test print.
] and [ ] and press
← →
SATO HT200e