SATO HT200e Operator's Manual page 42

SECTION 2: INSTALLATION AND SETUP
PROCESS ON THE SCREEN FOR TRANSFER OF PRESET DATA
Ｐ Ａ Ｒ Ａ Ｍ Ｅ Ｔ Ｅ Ｒ Ｃ Ｏ Ｐ Ｙ
1
Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｃ Ａ Ｒ Ｄ
[ ]
←
Ｄ Ａ Ｔ Ａ Ｓ Ｔ Ｏ Ｒ Ｅ ／ Ｒ Ｃ Ａ Ｌ Ｌ
2
Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
[ ]
←
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｓ Ｔ Ｒ ／ Ｒ Ｃ Ａ Ｌ Ｌ
3
Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｄ Ａ Ｔ Ａ Ｓ Ｅ Ｎ Ｄ ／ Ｒ Ｅ Ｃ
4
Ｈ Ｔ → Ｈ Ｏ Ｓ Ｔ
Ｈ Ｔ → Ｈ Ｏ Ｓ Ｔ Ｓ Ｅ Ｎ Ｄ Ｏ Ｋ ？
Or:
Ｈ Ｏ Ｓ Ｔ → Ｈ Ｔ Ｒ Ｅ Ｃ
Ｓ Ｅ Ｎ Ｄ Ｉ Ｎ Ｇ
Ｉ Ｔ Ｅ Ｍ
Or:
Ｒ Ｅ Ｃ Ｅ Ｉ Ｖ Ｉ Ｎ Ｇ
Ｉ Ｔ Ｅ Ｍ
Preset data that are transferred from a host computer will be registered in a printer. The data registered in the
printer can be transferred to the host.
Note: When preset data is transferred, on-line cable must be connected to the host before turning the power
"ON".
Page 2-24
6 + Power "ON"
Ｈ Ｏ Ｓ Ｔ → Ｈ Ｔ
Ｙ ／ Ｎ
Ｙ ／ Ｎ
:
０ ０ ０ １
:
０ ０ ０ １
Press [ENTR], so that it goes to the screen for the
selection of copying print parameter.
Press [
→
[ ]
→
Press [ENTR], so that it goes to the screen for the
selection of transferring print parameter.
Press [ ], so that it returns to the process No. 1.
←
Press [ ], so that it goes to the process No. 3.
→
[ ]
→
Press [ENTR], so that it goes to the screen for the
selection of the direction to transfer preset data.
Press [
←
For direction, select [
[ENTR] to go to the screen for the confirmation of
the receiving-and-sending.
Press [ENTR]:
"Y" is to start sending and receiving.
"N" is to return to the process No. 3.
Ｏ Ｋ ？
When sending one item is complete, the
number of items will be added.
After sending, it returns to the process No. 3.
When receiving one item is complete, the number
of items will be added.
After receiving, it returns to the process No. 3.
] , so that it goes to the process No. 2.
], so that it returns to the process No. 2.
]and [ ], and press
← →
SATO HT200e